Resumen del contenido incluido en la página 1
Owner's Manual
Liquid Propane Gas Grill
Model 141.153373
Natural Gas Grill
Model 141.173373
A WARNING: Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or installa-
Read this Owner's Manual carefully and be sure
tion.
your gas grill is properly assembled, installed and
maintained. Failure to follow these instructions
Note to Consumer: Leave this Owner's
could result in serious bodily injury and/or property
Manual in a convenient place for future reference.
damage
Resumen del contenido incluido en la página 2
/_kWARN ING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions .................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware ..................................................... 6 defects, or other reproductive harm. Parts Diagram and Lists ..................... 10 /_WARNING Assembly Instructions ............................. 13 Failure to comply w
Resumen del contenido incluido en la página 3
Correct LP Gas Tank Use • LP gas tanks must be stored outdoors in a LP gas grill models are designed for use with a well-ventilated area and out of the reach of standard 20 lb. Liquid Propane Gas (LP gas) tank, children. Disconnected LP gas tanks must not not included in grill box. Never connect your gas be stored in a building, garage or any other grill to an LP gas tank that exceeds this capacity. A enclosed area. tank of approximately 12 inches in diameter by 18-1/2 inches high is the maximum
Resumen del contenido incluido en la página 4
Figure 1 (Natural gas model only) IMPORTANT: your Kenmore Natural Gas Grill can- GAS SUPPLY not be converted to use LP Gas. Attempting to do iNSiDE so is extremely hazardous and will also void the grill WALL warranty. OUTSIDE WALL Your natural gas grill is designed to operate on TO GRILL natural gas only, at a pressure of 7" water column SHUTOFF (W.C.) (1/4 psi or 1.75 kpa), regulated at the LOCKING SHUT OFF residential meter. Check with your gas utility \ \ company for local gas pressure and wi
Resumen del contenido incluido en la página 5
CAUTION:Spidersandsmall insectsocca- To reduce the chance of "FLASHBACK" (see sionallyspinwebsor makenestsin the grill CAUTION at right) clean the Burner Tubes and BurnerTubesduringtransitand warehousing. Burners before fully assembling your grill. Re- move the Cotter Pin from the rear underside of Thesewebscan leadto a gasflow obstruc- tionwhichcouldresultin a fire in and each Burner using a pair of long nose pliers. aroundthe BurnerTubes.This typeof fire is Carefully lift each Burner up and aw
Resumen del contenido incluido en la página 6
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components $211G06352 Wheel Bolt 3/8"x3-3/8" 2 Install Wheels To Cart Legs $431M08152 Spring Washer 2 $372G06112 Nut 3/8" 2 $132G04322 Pattern Head Screw 1/4"x2" 8 Attaches Cart Legs To Cart Bottom Shelf S132G04082 Pattern Head Screw 1/4"xl/2" 4 Attaches Tank Pull-out Tray Assembly To Cart Bottom Shelf $132G04082 Pattern Head S
Resumen del contenido incluido en la página 7
LP GAS MODEL ONLY Size and Quantity of each Hardware Piece: Wheel Bolt 3/8"x3-3/8" Spring Washer 3/8" Nut 3/8" Qty. 2 Qty. 2 Qty. 2 Ref. # $431M08152 Ref. # S372G06112 Ref. # $211G06352 Pattern Head Screw 1/4"x3/4" Pattern Heed Screw 1/4"x2" Pattern Heed Screw 1/4"x1/2" Qty. 8 Qty. 12 Qty. 18 Ref. # S132G04122 Ref. # $132G04322 Ref. # $132G04082 Door Stop/Magnet Pattern Head Partly-Threaded Battery/AA Qty. 2 Screw 1/4"x5/8" Qty. 1 Ref, # P05318022B Qty. 4 Ref. # P05301001A Scale 1:2 Ref. # S135G
Resumen del contenido incluido en la página 8
The followingtable illustrates a breakdown of the hardwarepack.It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components Wheel Bolt 3/8"x3-3/8" 2 S211G06352 Install Wheels To Cart Legs S431MO8152 Spring Washer 2 S372GO6112 Nut 3/8" 2 S132G04322 Pattern Head Screw 1/4"x2" 8 Attaches Cart Legs To Cart Bottom Shelf Pattern Head Screw 1/4"x1/2" 4 Attaches Cart Rear Panel To Cart S132G04082 Pattern Head Screw 1/4"x2" 4 Attaches Door Bracket To
Resumen del contenido incluido en la página 9
NATURAL GAS MODEL ONLY Size and Quantity of each Hardware Piece: Wheel Bolt 3/8"x3-3/8" Spring Washer 3/8" Nut 3/8" Qty. 2 Qty. 2 Qty. 2 Ref. # $431M08152 Ref. # $372G06112 Ref. # $211G06352 Pattern Head Screw 1/4"x3/4" Pattern Heed Screw 1/4"x2" Pattern Heed Screw 1/4"x1/2" Qty. 8 Qty. 12 Qty. 16 Ref. # $132G04122 Ref. # $132G04322 Ref. # $132G04082 Pattern Heed Partly*Threeded Battery/AA Door Stop/Magnet Screw 1/4"x5/8" Qty. 2 Qty. 2 Ref, # P05301001A Ref. # P05318022B Qty. 4 Ref. # $135G04101
Resumen del contenido incluido en la página 10
LPG = Liquid Propane Gas NG = Natural Gas 10_ \ 61 23 6O 41 37 2O 19 17 / 12 11o 30(LPG only) 23_(NG only)_ 31(NG only) 26\ \ 22 32\ 64 62 / (NO (LP6 18 3b lb / (LPC 47 only) 4b \ (LPG only) _Sb(LPG only) "53 b4 69(LPG only) j70(LPG only) 46 \ _480(NG only) _71(NG only) lO
Resumen del contenido incluido en la página 11
REF# DESCRIPTION PART# QTY 1. Lid Plate 1 P00117336A 2. Lid Side Panel, Left P00105227P 1 P00106227P 1 3. Lid Side Panel, Right P00607153A 1 4. Temperature Gauge 5. Lid Handle 1 P00205030B 6. Lid Handle Heat-Insulating Spacer P06801002A 2 7. Name Plate P00410037C 1 P01508026E 1 8. Cooking Rack/Secondary 9. Cooking Grid P01615027E 3 10. Flame TamedSteel P01705016E 3 11. Burner/Main 6 P02001006C 11a. Burner Air ShuttedMain (NG only) P05524060C 6 12. Burner Bracket P02206251B 1 13. Gas Collector Bo
Resumen del contenido incluido en la página 12
REF# DESCRIPTION PART# QTY 1 44, Cart Leg, Left P00901001C 1 45, Cart Leg, Right P00902030C 46, Cart Rear Panel PO7702009B 1 47, Door Bracket PO3301016D 1 48a, Door, Left P04302010A 1 1 48b, Door, Right (LPG only) P04301010A 1 48c, Door, Right (NG only) P04303014A 49, Door Handle PO0215019H 2 50, Door Stop/Magnet PO5318022B 2 1 51, Tank Pull-Out Tray Assembly (LPG only) Y0340020 1 52, Fuel Gauge Display (LPG only) P05310005B 53, Wheel P05102017A 2 2 54, Weel Hub Cap P05111018A 55, Caster, 3 in,,
Resumen del contenido incluido en la página 13
Figure 1 CART LEG CAUTION: Whileitispossible foroneperson to LEFT CART LEG BRACKET_ assemble this grill, obtain assistance from another f person when handling some of the larger, heavier pieces, especially the grill head. 1. During unpacking and assembly always wear work gloves and eye protection. 2. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and RIGHT CARTLEG use as a work surface to protect floor and grill parts / from scratches. 3. Slice all ca
Resumen del contenido incluido en la página 14
7. Install the Door Bracket to the inside of front Figure 4a (LP gas model only) Cart Legs. Align the threaded holes on the Door Bracket with the holes on Cart Legs. Tighten securely using 4 of the 1/4"x2" Pattern Head Screws provided. (See Figure 3 on page 13) Upper door bolt holes (at ends of bracket) must face outward. DOOR _ BRACKET [] Installing The Cabinet Doors DOORSTOP _ Found in For LP Gas grills: Hardware Pack 1. Install the Door Stops to the Cart Bottom Shelf and the Door Bracket. See
Resumen del contenido incluido en la página 15
Figure 5a (NG gas model only) [] Installing The Cabinet Doors For Natural Gas grills: 1. Install the Door Stops to the Cart Bottom Shelf and the Door Bracket. See Figure 5a. 2, Align the holes on the Door Stops with the DOOR _ threaded holes on the top of the Cart Bottom BRACKET Shelf and bottom side of Door Bracket. Tighten securely using 4 of the 1/4"xl/2" Pattern Head Screws provided. See Figure 5a. DOOR STOP J Found in Hardware Pack , Remove the white protective film from the stainless steel
Resumen del contenido incluido en la página 16
Figure 6a (LP gas model only) _llnstalling The Grill Head GRILL HEAD BOWL SIDE PANEL 1. Now that you've assembled the grill cart you can install the pre-assembled Grill Head. See ELECTRIC WIRE FROM GRILL HEAD Figure 6a or 6b. If you haven't already done so, we suggest you open the Grill Lid and remove the packed components. Even with the components removed, this next step requires 2 CARTLEG BRACKET people. BE CAREFUL NOT TO PINCH FINGERS WHEN LOWERING HEAD ONTO CART WiRE FASTENER 2. For LP Gas g
Resumen del contenido incluido en la página 17
Figure 8a [] Installing Side Shelf, Side Burner and Tool Holder Kit SIDE SHELF Remove Side Burner from Side Burner Kit GRILL HEAD before installing. 1. Enlisting the aid of an assistant, attach Side Burner Frame to right side of grill. Attach Side Shelf to S_DE BURNER left side of grill as shown in Figure 8a. Align FRAME the 4 holes on Side Shelf and Side Burner Frame with the threaded holes on left and right Bowl Support Brackets. Tighten securely using 4 of the 1/4"x3/4" Pattern Head Screws pr
Resumen del contenido incluido en la página 18
Figure 8d (Natural Gas model only) 6. For Natural Gas grills: Connect the Electric Wire terminal from Side Burner with the other from Grill Head. See Figure 8d. Bind SIDE BURNER POT SUPPORT the connected Electric Wires, and Connection Tube together using the supplied Fastening Band. \\\\\ 7. The gap between the Side Burner Electrode Tip and _StDB BURNER the Side Burner Port should be approximately 1/8"~3/16". See Figure 8e. If the gap is wider than 3/16", use a pair of long nose pliers and gentl
Resumen del contenido incluido en la página 19
[] Ignitor Battery Installation - See Fig. 9 [] Electrode Check - Requires an Assistant Before placing the cooking components into your 1. Remove the Ignitor Caps on the grill Control grill, ensure that the Spark Electrode Tip is properly Panel. positioned within each Gas Collector Box ( a 3-1/4" wide stainless mechanism found at the front 2. Place the manufacturer supplied AA battery between each set of Burners.) The easiest way to into Ignitor Slot. Be sure to place the positive ensure this is
Resumen del contenido incluido en la página 20
Figure 11 [] Installing Cooking Components Important: Before cooking on your grill the first SECONDARY COOKING RACK time, wash the Cooking Grids and Cooking Rack with warm, soapy water. Rinse and dry thoroughly. Season with cooking oil regularly. After cooking is COOKING GRID completed, tum grill to HIGH setting three to five minutes to burn off excess grease or food residue. STEELFLAME TAMER 1. Place the three Steel Flame Tamers on the lower ledge above Bumers. See Figure 11. 2. Evenly space th
