Resumen del contenido incluido en la página 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlaingroup.com
GARAGE DOOR OPENER
Models PD210 -1/2 HP
PD212 -1/2 HP
For Residential Use Only
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless the Protector System is connected and properly
aligned.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Introduction Pages 2-7 Adjustment Pages 28-30 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................28 Preparing your garage door ........................................3 Adjust the force .........................................................29 Tools needed...............................................................3 Test the safety reversal system.................................30 ® Plannin
Resumen del contenido incluido en la página 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d
Resumen del contenido incluido en la página 4
— — — — — — — — Planning • Do you have an access door in addition to the Identify the type and height of your garage door. garage door? If not, Model 7702CB Outside Quick Survey your garage area to see if any of the Release is required. See Accessories page. conditions below apply to your installation. Additional • Look at the garage door where it meets the floor. materials may be required. You may find it helpful to Any gap between the floor and the bottom of the refer back to th
Resumen del contenido incluido en la página 5
Slack in Chain Tension is Normal When Garage Door is Closed Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • Generally, a one-piece door does not require CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage reinforcement. If your door is lightweight, refer to door. the information relating to sectional doors in • The gap between the bottom of the garage door and Install
Resumen del contenido incluido en la página 6
Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and the parts illustrated below. Note that accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and packing material until installation and adjustment is complete. Model PD210 (1) Model PD212 (2) ® Motor Unit with a Light Lens SECUR
Resumen del contenido incluido en la página 7
NOTICE Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Hex Bolt Carriage Bolts Washered Bolt Nut 5/16"-18x7/8" (3) 1/4"-20x1/2" (12) 5/16"-18x1/2" (2) 5/16"-18 (5) Master Link (2) (mounted in opener) Trolley Lock Nut Lock Washer Threaded Shaft (1) 1/4"-20x7/16" (12) 5/16" (4) INSTALLATION HARDWARE Lag Screw Hex Bolt 5/16"-9 x1-5/8" (2) Nut 5/16"-18 (4) Lock Washer 5/16" (4) 5/16"-18x7/8" (4) Lag Screw 5/16"-18x1-7/
Resumen del contenido incluido en la página 8
ASSEMBLY STEP 1 Assemble the T-Rail and Attach the Cable Pulley Bracket To avoid installation difficulties, do not run the HARDWARE garage door opener until instructed to do so. SHOWN ACTUAL SIZE 1. Align the four T-rail sections on a flat surface Carriage Bolts exactly as shown. Center sections are Lock Nut 1/4"-20x1/2" 1/4"-20 interchangeable. Front and back sections are also interchangeable for ease of assembly. 2. Insert the carriage bolts so the square bolt necks seat in the square holes i
Resumen del contenido incluido en la página 9
ASSEMBLY STEP 2 Inner Nut Lock Install the Trolley 5/16" Washer 5/16" • Attach the trolley threaded shaft to the trolley with Outer Nut Trolley the lock washer and nuts as shown. 5/16" Threaded Shaft • As a temporary stop, insert a screwdriver into the hole in the front end of the T-rail. Trolley • Slide the trolley assembly along the rail to the screwdriver stop. NOTE: If trolley hits against any nuts on the T-rail, the bolts and nuts were attached from the wrong side and must be repositioned.
Resumen del contenido incluido en la página 10
ASSEMBLY STEP 4 WARNING WARNING Install the Chain/Cable To avoid possible SERIOUS INJURY to fingers from and Attach the Sprocket Cover moving garage door opener: CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating INSTALLING THE CHAIN/CABLE opener. • Securely attach sprocket cover BEFORE operating. 1. Pull the cable loop from Leave Chain the carton and fasten it & Cable Inside Carton to to the trolley with a Prevent Kinking. master link from the hardware bag. (See Figure 1) Ma
Resumen del contenido incluido en la página 11
ASSEMBLY STEP 5 Tighten the Chain and Cable • Spin the inner nut and lock washer down the Lock trolley threaded shaft, away from the trolley. Inner Nut Outer Nut Washer • To tighten the chain, turn outer nut in the direction To Tighten Outer Nut shown. AS YOU TURN THE NUT, KEEP THE CHAIN FROM TWISTING. To Tighten Inner Nut • When the chain is approximately 1/2" (1.3 cm) above the base of the T-rail at its midpoint, re- tighten the inner nut to secure the adjustment. Sprocket noise can result if
Resumen del contenido incluido en la página 12
INSTALLATION STEP 1 Finished Vertical Determine the Header Bracket Ceiling Centerline Location Header Structural 2x4 Wall Supports WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if mounting header Vertical bracket or 2x4 into masonry. Centerline •
Resumen del contenido incluido en la página 13
ONE-PIECE DOOR WITHOUT TRACK Unfinished 1. Close the door and mark the inside vertical Ceiling centerline of your garage door. Extend the line Structural onto the header wall above door, as shown. Supports Header Wall Vertical If headroom clearance is minimal, you can install Centerline the header bracket on the ceiling. See page 14. 2x4 If you need to install the header bracket on a 2x4 2x4 OPTIONAL (on wall or ceiling), use lag screws (not provided) CEILING MOUNT to securely fasten the 2x4 to
Resumen del contenido incluido en la página 14
INSTALLATION STEP 2 Wall Mounting Holes Install the Header Bracket CEILING MOUNT ONLY The nail hole is for You can attach the header bracket either to the wall positioning only. above the garage door, or to the ceiling. Follow the You must use lag screws UP to mount the header bracket. instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Optional Wall Mounting Holes
Resumen del contenido incluido en la página 15
INSTALLATION STEP 3 Attach the T-Rail to the Header Bracket Header Wall • Position the opener on the garage floor below the header bracket. Use packing material as a Header protective base. Bracket NOTE: If the door spring is in the way you’ll need Cable help. Have someone hold the opener securely on Pulley a temporary support to allow the rail to clear the Bracket spring. • Position the rail bracket against the header bracket. • Align the bracket holes and join with a clevis pin as shown. • Ins
Resumen del contenido incluido en la página 16
WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door- Rail to-T-rail distance. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open the door all the way a
Resumen del contenido incluido en la página 17
INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Two representative installations are shown. Yours CAUTION WARNING supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be angled if installing any brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before inst
Resumen del contenido incluido en la página 18
1 LIGHT LIGHT LIGHT WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of the door at a • Be sure power is not connected BEFORE installing door minimum height of 5 feet (1.5 m) where small children control. cannot reach, and away from moving parts of the door • Connect ONLY to 24 VOLT low voltage wires. and door hardware. The installation surface must be To prevent possible
Resumen del contenido incluido en la página 19
NOTICE WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Lights To prevent possible OVERHEATING of the endpanel or light socket: • Press the release tabs on both sides of lens. Gently • DO NOT use short neck or specialty light bulbs. rotate lens back and downward until the lens hinge • DO NOT use halogen bulbs. Use ONLY incandescent. is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in the 100 Watt (Max) socket. The lights will t
Resumen del contenido incluido en la página 20
INST WARN ALLAING TION STEP 9 WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wi
