Manual de instrucciones de Havis-Shields K9/Prisoner Transport Unit KK-K9-C20-K-PT

Resumen del contenido incluido en la página 1

INSTALL INSTRUCTIONS KK-K9-C20-K-PT
K9/PRISONER TRANSPORT UNIT
2007-2008 CHEVROLET/GMC TAHOE/YUKON

TOOLS REQUIRED:
Ratcheting wrench Powered drill
Socket & Metric socket sets Screwdriver set
Drill bit set

HARDWARE:
QTY DESCRIPTION PART #
20 ¼-20 x ½” Stainless Carriage Bolts GSM32022
30 ¼-20 x ¾” Stainless Carriage Bolts GSM32024
50 ¼-20 Hex Flange Serrated Nuts Zinc GSM30023
6 ¼” x 1” Hex Head Lag Bolt GSM33060
22 #12 x ¾” Stainless Sheet Metal Screws GSM34177
2

Resumen del contenido incluido en la página 2

K9 Assembly Upper prisoner filler panel K9 tunnel assembly Rear prisoner filler panel Driver-side floor Passenger-side “B” pillar mounting bracket mounting brackets Two “L” Brackets See photos Lower prisoner filler panel Front prisoner filler panel & Passenger-side floor Front prisoner mounting bracket seal panel Always!
Read all instructions before installing any H

Resumen del contenido incluido en la página 3

Remove “B” Pillar Trim, Seat belt bolt and Grab Handle Reuse OEM Grab handle bolts and attach “L” brackets to grab handle mount holes Remove passenger door panels, door handles and speakers Note: Reconnect window switches and wire tie parts so they do NOT interfere with window operation. Remove dual passenger Leave the single Note: Wrap OEM switch seat assembly passenger-side seat with Plastic bag to protect from water installed KK-K9-C20-K-PT_INST_10-07

Resumen del contenido incluido en la página 4

1. Mount 7” bracket at Top and 5” bracket at bottom 2. Seat belt mount bracket lower tab may need to be slightly bent out of the way 3. Reattach seat belt bolt and trim and Cut Plastic Trim at “L” bracket if necessary. 4. Mount Partition to “L” brackets. Passenger-side Driver-side Set height at 7.5” Assemble Mounting feet to floor plates in locations shown above Attach to existing seat Slide in Main K9 Housing and rest on mounting feet. bolt studs with O.E.M seat bolt

Resumen del contenido incluido en la página 5

Line up driver and passenger-side floor mounting brackets and loosely attach to K9 main housing, using ¼” x ¾” stainless carriage bolts and serrated nuts. **Do not tighten hardware until the side tunnel is set in place** Attach upper prisoner Attach driver side tunnel with ½” long and ¾ “ long filler panel using existing carriage bolts. Position K9 unit so tunnel lines up with ¼ x ¾” stainless carriage rocker panel plastic trim. Move driver seat to rear most bolts and serrated n

Resumen del contenido incluido en la página 6

#1 #2 #1 #2 1.Attach rear prisoner filler 1. Attach front prisoner filler panel to K9 main housing panel to K9 main housing using ¼ x ¾” stainless carriage bolts and serrated nuts. using ¼ x ¾” stainless 2. Attach front prisoner partition to previously mounted carriage bolts and serrated “B” pillar mounting brackets using ¼ x ¾” stainless nuts. carriage bolts and serrated nuts. 2.Attach to floor using ¼” x 1” hex head lag bolts. Be Caution…Always Check under vehicle for obs

Resumen del contenido incluido en la página 7

Center door panel on door. With door panel installed, hold up window guard assembly with top Push down and drill mount bracket between rubber and metal frame. Guard hinge will sit on holes with 1/8” bit. Attach with top of door panel. Mark location of top bracket and hinge. #10 x ¾” Sheet metal screws Hold top bracket in its location, mark the four mount holes and Remove top bracket drill with 1/8” drill bit. Carefully hold rubber gasket away from from window guard drill. Drill