Resumen del contenido incluido en la página 1
Installation and Wire
English connection manual
VRX935VD
Installation and Wire connection manual
Contents
1. BEFORE STARTING ............................................................... 65
2. PACKAGE CONTENTS ........................................................... 65
3. GENERAL CAUTIONS ............................................................ 66
4. CAUTIONS ON INSTALLATION .............................................. 66
5. INSTALLING THE MAIN UNIT .................................
Resumen del contenido incluido en la página 2
Installation and Wire English connection manual 3. GENERAL CAUTIONS 1. Do not open the case. There are no user ser- 2. Use a soft, dry cloth to clean the case. Never viceable parts inside. If you drop anything use a rough cloth, thinner, benzine, or alco- into the unit during installation, consult your hol, etc. For tough dirt, apply a little cold or dealer or an authorized CLARION service warm water to a soft cloth and wipe off the centre. dirt gently. 4. CAUTIONS ON INSTALLATION 1. Prepare a
Resumen del contenido incluido en la página 3
Installation and Wire English connection manual 5. INSTALLING THE MAIN UNIT Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. Notes: 3. Insert the main unit into the universal mount- 1) Some car models require special mounting kits ing bracket until it locks. for proper installation. Consult your Clarion
Resumen del contenido incluido en la página 4
Installation and Wire English connection manual Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the rection of arrow to remove it. Repeat the dashboard. same for the other side to remove the springs from the both sides. (Figure 7) If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and 2. Secure the mounting brackets to the chassis screws marked (∗). (Figure 8) as shown in Figure 8. Hol
Resumen del contenido incluido en la página 5
Installation and Wire English connection manual 6. REMOVING THE MAIN UNIT 1. When the rear of the main unit has been se- pull the main unit out by the hook plate. (In- cured with the method shown in Figure 6 un- sert both the right and left edges of the hook fasten the special screw. plate.) (Figure 9) 2. Remove the outer escutcheon. Note: Keep the hook plate. You cannot remove the 3. Insert the hook plate between the spring and main unit without disengaging the hook plate. the universal mounti
Resumen del contenido incluido en la página 6
Installation and Wire English connection manual 8. WIRE CONNECTION Securely connect to the metal part of the car with a Black screw, etc. Choke coil Main power supply cord Yellow Fuse Power supply lead Main unit Connection cord (provided with this unit) CeNET cable (Sold separately) Power supply lead VIDEO output (RCA) ∗5 VISUAL 1 audio input terminal L+R (RCA) VISUAL 1 video input (RCA)/ DVD changer input (RCA) & TV TUNER input (RCA) Reset switch Top view of the tuner amp unit 5.1ch surrou
Resumen del contenido incluido en la página 7
Installation and Wire English connection manual Purple/Black 2 Purple 1 Green/Black 8 Blue/White 0 Green 7 Brawn *∗1 Glay 3 Grass-green ) No. Description Glay/Black B 1 REAR RIGHT 4 2 REAR RIGHTv B Orange/White 3 FRONT RIGHT ! 4 FRONT RIGHTv B 5 FRONT LEFT White/Black 6 FRONT LEFTv 6 B 7 REAR LEFT Red 8 REAR LEFTv @ 9 +12 V MAIN POWER White 0 Amplifier turn-on lead 5 ! ILLUMINATION @ +12 V ACCESSORY Yellow 9 # GROUND $ CCD camera ( % VISUAL 2 terminal Black ¥ Radio antenna jack (∗2) # & CeNET te
Resumen del contenido incluido en la página 8
Installation and Wire English connection manual Connecting the Accessories • Connection to the external amplifier The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For detailed information, refer to the instruction manual of the 5.1ch Surround Decoder. • Connection to the CCD camera for vehicle The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed information, refer to the instruction sheet or manual for the CCD
Resumen del contenido incluido en la página 9
Installation and Wire English connection manual CeNET RCA Cable (Visual) 9. SAMPLE SYSTEMS Sample System 1 MAIN UNIT VRX935VD RCA Cable (Visual) VISUAL 2 IN Tuner IN TTX7501z TUNER AMP (CeNET TV TUNER) UNIT VTR CeNET CCA-389 VISUAL 1 IN RCA Cable (Visual) Rear view monitor DSH920S (SIRIUS TUNER) CeNET VCZ625 (DVD CHANGER) CeNET Mode* Front Speaker Rear Speaker *Switch the MODE switch to the CeNET mode. CCA-519-500 DCZ625 (CD CHANGER) VRX935VD 73
Resumen del contenido incluido en la página 10
Optical Digital Cable CeNET (included (sold separately, the DVH920) DCA-005/008) CeNET (included the VCZ625) RCA Cable (Visual) (included the VCZ625) RCA Cable (Visual) RCA Cable (sold separately) RCA Cable (included the SRK601) Installation and Wire English connection manual Sample System 2 MAIN UNIT VRX935VD (Gray) Optical Digital Cable (included the DVH920) RCA Cable (Visual) VISUAL 2 IN Tuner IN TTX7501z (CeNET TV TUNER) TUNER AMP VTR UNIT CeNET CCA-389 VISUAL 1 IN (LINE IN)D N(LINE OUT)
Resumen del contenido incluido en la página 11
Installation and Wire English connection manual Optical Digital Cable (sold separately, DCA-005/008) CeNET (included the DVH920) CeNET (included the VCZ625) RCA Cable (Visual) RCA Cable (Visual) (included the VCZ625) RCA Cable (sold separately) RCA Cable (included the SRK601) Sample System 3 MAIN UNIT VRX935VD (Gray) Optical Digital Cable (included the DVH920) RCA Cable (Visual) VISUAL 2 IN Tuner IN TTX7501z TUNER AMP (CeNET TV TUNER) UNIT VTR CeNET CCA-389 VISUAL 1 IN RCA Cable (LINE IN)D N(
Resumen del contenido incluido en la página 12
76 VRX935VD
