Resumen del contenido incluido en la página 1
7” Under-the-Counter LCD
FCM-0700A
Operating Manual
Resumen del contenido incluido en la página 2
Table of Contents Table of Contents ----------------------------------------------------------- 2 Important Safety Instruction--------------------------------------------- 3 FCC Notice--------------------------------------------------------------------- 5 Characteristic Features --------------------------------------------------- 6 Front Panel -------------------------------------------------------------------- 7 Rear Panel and Display Panel-------------------------------------
Resumen del contenido incluido en la página 3
Important Safety Instruction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a ri
Resumen del contenido incluido en la página 4
Important Safety Instruction Notes: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, he
Resumen del contenido incluido en la página 5
FCC Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran
Resumen del contenido incluido en la página 6
Characteristic Features This product has incorporated LCD TV Functions display, TV receiver and radio function Receive TV signal clearly. in one system. It is designed for Search for TV channels automatically. convenient use in the kitchen; please Memorize the channels automatically. refer to page 21 for the installation instructions. Radio Functions Receive AM/FM signal clearly. Multiple Mode Search for radio stations automatically. TV mode Stor
Resumen del contenido incluido en la página 7
Front Panel Front Panel Drawing 1. POWER button 10. SEEK + button Under radio mode, press once to fine Press to access to or exit the STANDBY tune frequency forward. Press for about mode. 1.5 seconds to search radio stations 2. TV button forward automatically. Press to enter TV mode. Or under TV 11. MUTE button mode, press to display the current Press to turn on or off the speaker channel number o
Resumen del contenido incluido en la página 8
Rear Panel and display panel 16. ► Press to adjust the value downward Press to select items in the setup menu. when setting the time on the display Or press to increase the volume. Or panel. press to increase the value in the picture 19. ◄ setup menu. Press to select items in the setup menu. 17. MENU button Or press to decrease the volume. Or Press to enter the system setup menu. press to decrease the value in the 18. ▼ picture setup menu. Press to select items in the setup me
Resumen del contenido incluido en la página 9
Remote Control Preparation Use Of Remote Control Refer to the drawing, and remove the Please directly point the r/c towards the main unit when operating. The r/c works empty battery receptacle. properly in a distance below 7m and at an angle of up to 60°to the front of the unit. No obstacles may stand in the way between r/c and infrared sensor. Insert the battery into the receptacle, please make sure the polarity match
Resumen del contenido incluido en la página 10
Remote Control Remote Control Drawing 1. POWER button 4. AM button Press to access to or exit from the Press to shift to AM signal input mode. STANDBY mode. 5. AV button 2. TV button Press to shift to external AV input mode. Press to enter TV mode. 6. MENU button 3. FM button Press to enter the system setup menu. Press to shift to FM signal input mode. - 10 -
Resumen del contenido incluido en la página 11
Remote Control 7. OK button 13. 0-9 number buttons Press to confirm selections. Select numbers by pressing these buttons. 8. 14. SEEK +/- button Press to select menu items or settings. Under radio mode, press once to fine Press buttons to adjust volume. Or tune frequency forward or backward. press to adjust value in the picture setup Press for about 1.5 seconds to search menu. radio stations forward or backward Press buttons to select channels or automatically. r
Resumen del contenido incluido en la página 12
System Connections • Do not connect the power cord until all other connections have been made. • Each time you restart the unit, it remembers the last function used. Connecting To External AV Signal Source Connections should be made as follows: Connecting To TV Signal Input Source - 12 -
Resumen del contenido incluido en la página 13
System Connections Connecting To Antenna Connect the supplied AM/FM antennas to listen to the radio. • In order to improve the signal, move AM loop antenna away from system and other equipment. • Extend FM antenna fully. • Keep the FM antenna as horizontal as possible after connection. • When connecting the supplied AM loop antenna, connect two black cords to AM and ground jacks as shown below. • If the FM reception is poor, please
Resumen del contenido incluido en la página 14
System Connections Connecting To the Power Adapter This unit is powered via the switching power adapter (supplied). See the below figure for details: 1. Connect the AC adapter to jack marked with “DC 12V IN” on the rear panel of the unit. 2. Plug the two-prong end of the power cord to the grounded electrical socket. 3. When not using the unit, turn off the power of the unit first, and then unplug the power supply to prevent malfunctions.
Resumen del contenido incluido en la página 15
Radio Function Radio Function Operation Press the AM or FM button on the remote control or front panel to enter AM or FM radio mode. Then press the SEEK+/- button for about 1.5 seconds on the remote control or front panel to start searching forward/backward from the current frequency. Press the SEEK+/- button again to stop searching. Radio frequency will be displayed on the display panel. The frequency range of FM is from 87.5MHz to 107.9MHz, frequency range of AM i
Resumen del contenido incluido en la página 16
TV Function Basic Operation Connect the antenna to the antenna jack on the rear panel. After connecting the antenna, connect the power supply cord. If the player is in standby mode, press the POWER button on the front panel to turn on the power. Press the TV button on the remote control to shift to TV mode. Press the CHANNEL+/- buttons or buttons on the remote control, or use the number buttons directly, to select the desired channel. Some prefe
Resumen del contenido incluido en la página 17
TV Function Use the ▼, ▲ buttons to select the item you want to set. Use the ►, ◄ buttons to enter the item and to select. Press the ► button on the remote control to exit from the setup menu. Press the ◄ button on the remote control to return to the picture setup menu. Signal Use the ► direction button to select CATV TV signal input mode. Use the ◄ direction button to select AIR TV signal input mode. Channel Use the ►, ◄ buttons to change the c
Resumen del contenido incluido en la página 18
TV Function The auto memory will take a few minutes. The unit will search channels from the lowest channel to the highest channel in the standard channel list. When tuning operations are complete the unit will exit and store the channels by sequence in the memory. During tuning, press the ◄ button to exit the auto memory. Use the CHANNEL +/- or ▼, ▲ direction buttons to select the desired channel from those in memory. Timer Setup Press the SET but
Resumen del contenido incluido en la página 19
TV Function Power off To set the playback end time of the signal source use number buttons to input the desired time in sequence of hour, minute. Press the ►, ◄ direction buttons to shift between am and pm. When the playback of the signal source is over, the player will enter standby mode. Signal Use the ►, ◄ direction buttons to select CATV, AIR, FM or AM. Channel Use number buttons to input the desired TV channels. In CATV signal input mode,
Resumen del contenido incluido en la página 20
AV Function AV Function The player has an additional AV input so it can function as a monitor for a DVD player, video cassette player, satellite receiver, video game, etc. When an AV source is connected, press the AV button on the remote control to enter external input AV mode. Picture Parameter Setup Press the MENU button once on remote control to enter PICTURE setup menu, and screen will display as shown: PICTURE Brightness
