Manual de instrucciones de Linear ACCESS AK-21

Resumen del contenido incluido en la página 1

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,AK-21 - LINEAR P/N: 228045 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - FOLDING: ALBUM-FOLD - BINDING: SADDLE-STITCH
AK-21
Digital Keyless
Entry System
Installation and Programming Instructions
(760) 438-7000
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
228045 A IMAGE 1

Resumen del contenido incluido en la página 2

CONTENTS FEATURES COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ✓ FOUR INTERCHANGEABLE KEYPAD BEZELS WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Supplied with Model AK-21 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ✓ KEYPAD PROGRAMMABLE Opening the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Resumen del contenido incluido en la página 3

COMPONENT LOCATIONS MASTER CODE RED/GREEN YELLOW RESET JUMPER POWER/ACCESS "LOCKOUT" (JP2) INDICATOR INDICATOR TERMINAL BEZEL BLOCK #2 (TB2) SOLID STATE WHITE LED DOWN LIGHT TERMINAL BLOCK #1 (TB1) FACEPLATE KEYPAD BEEPER MOUNTING LEVEL PLATE JUMPER (JP1) Figure 1. Component Locations WIRING DIAGRAM TYPICAL DOOR INSTALLATION WIRING AK-21 TERMINALS TERMINAL TERMINAL BLOCK 2 BLOCK 1 12-24 VOLT 1 - AC OR DC SENSE - 8 POWER N.C. DOOR AC OR DC SUPPLY SWITCH 2 - AC OR DC COM - 7 POWER 3 - N.O. REQUEST

Resumen del contenido incluido en la página 4

Install the Electrical Box and Mounting Plate INSTALLATION The keypad is designed to fi t into a standard single-gang electrical Before installing the keypad, the unit must be partially box. Select a location near the controlled door and choose a disassembled to access the mounting plate. The keypad’s bezel convenient height for the keypad. Be sure there is good wiring can be exchanged for a different color when the keypad is apart. accessibility for the unit’s power and the output to the do

Resumen del contenido incluido en la página 5

Keypad Wiring 2 WIRES See Figure 7 for an example of a basic door installation. The DOOR FOR DOOR SENSE keypad is mounted adjacent to the door. An electric door strike SENSE SWITCH is mounted in the door jamb to release the door lock. A magnetic SWITCH switch is mounted on the top of the door jamb for detecting when the door is open. Use the following steps to wire the keypad. Refer to the wiring 2 WIRES diagram shown in Figure 8 to assist in the wiring. AK-21 FOR DOOR ☞ NOTE: Up to 500 feet

Resumen del contenido incluido en la página 6

FACTORY DEFAULTS Adding a New Entry Code MASTER PROGRAMMING CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123456 Press: 01 # Code # Code # Action # ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITS Code = The new entry code: 1-999999, depending on code length REQUEST-TO-EXIT OUTPUT RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAIN RELAY Action = Relay output entry co

Resumen del contenido incluido en la página 7

PROGRAMMING OPTIONS Select Request-to-Exit Output Default: Main Relay There are several AK-21 programming options. For most Sets which output activates when the Request-to-Exit input is grounded. This output may be timed or toggled. installations, the factory set default options are suffi cient. The keypad must be in Programming Mode to make these changes. Press: 1 6 # Output # Select Door Sense or Inhibit Input Default: Door Sense Output = Output to Activate (0-4) The input on Terminal Block

Resumen del contenido incluido en la página 8

AK-21 OPERATION Beep Sounds During Auxiliary Relay Default: No Selects whether or not the keypad beeps during Auxiliary Relay activation. Keypad users request access by entering their code. ❑ Users of the AK-21 have up to 40 seconds to key in their Press: 4 2 # Sound # entry code. Sound = 1 for Yes, = 0 for No ❑ Up to eight seconds are allowed between each keystroke. ❑ All digits of the entry code must be entered. Example: If the code is 0042, the user must enter Beep Sounds During Output #3