Resumen del contenido incluido en la página 1
Contents
Introduction........................................................................................................................................... 1
Notational conventions ................................................................................................................. 2
Important notes..................................................................................................................................... 2
Safety notes............................
Resumen del contenido incluido en la página 2
Contents Display modes.....................................................................................................................................31 Main display mode ......................................................................................................................31 PIP mode (Picture in Picture)......................................................................................................32 Technical data...................................................
Resumen del contenido incluido en la página 3
Introduction Your new LCD TV MYRICA V40-1 possesses a whole range of useful features and functions, e.g.: ● TFT monitor (Thin Film Transistor; active matrix) ● analogue tuner for VHF, UHF and cable programmes ● connections for SCART (video and RGB), video and S-Video ● minimal space requirements thanks to slim casing ● optimum ergonomic characteristics (totally distortion-free and colour purity right into the corners) ● high degree of brightness and good contrast ● high resolution fo
Resumen del contenido incluido en la página 4
MYRICA V40-1 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. ! Supplementary information, remarks, and tips follow this symbol. i ► Text which follows this symbol describes activities that must be performed in the order shown. "Quotation marks" indicate names of chapters
Resumen del contenido incluido en la página 5
MYRICA V40-1 ● The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the socket. ● Lay all cables so that nobody can stand on them or trip over them. When attaching the device, observe the relevant notes in the "Preparing for use" chapter. ● If you use a different PC data cable from the one supplied, ensure that it is adequately shielded. CE conformance and optimum picture quality are guaranteed onl
Resumen del contenido incluido en la página 6
MYRICA V40-1 Cleaning ● Remove the power plug before cleaning the device. ● Do not clean any interior parts yourself, leave this job to a service technician. ● Do not use any cleaning agents that contain abrasives or may corrode plastic. ● Ensure that no liquid will run into the system. ● Ensure that the ventilation areas of the device are free. ● The display surface of the device is sensitive to pressure and scratches. Clean it only using a soft, slightly moistened cloth. Wipe the dev
Resumen del contenido incluido en la página 7
MYRICA V40-1 Disposal and recycling This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging. The device may be taken back after use to be recycled, provided that it is returned in a condition that is the result of normal use. Any components not reclaimed will be disposed of in an environmentally acceptable manner. If you have questions on disposal, please contact your point of sal
Resumen del contenido incluido en la página 8
MYRICA V40-1 Preparing remove control Inserting batteries ► Open the back cover of the remote control by sliding it in the direction of the arrow. ► Place the batteries supplied in the battery compartment. Ensure correct polarity. ► Close the battery compartment by sliding the cover back on until you hear and feel it click into place. Remove the batteries when not using the remote control for longer periods. i Handle the remote control with care. Do not drop the remote control
Resumen del contenido incluido en la página 9
MYRICA V40-1 Removing the foot (when using a wall bracket) Before you can use a wall bracket, the foot must first be removed: The wall bracket is not included in the consignment of the TV. i The foot is shown as an example in the following illustrations. The delivered foot may differ from the illustration. ► Carefully lay the TV on a smooth, clean work surface with the front facing downward. Ask someone to help you. Even small knocks can damage the device. ! Make sure that no o
Resumen del contenido incluido en la página 10
MYRICA V40-1 Installing LCD TV Ventilation To ensure sufficient ventilation, the intake and exhaust air openings of the device must never be blocked. ! When installing the TV in niches, maintain the minimum distance for sufficient ventilation of the device: 10 cm from the side and back, 20 cm from the top. 8 - English A26361-K1070-Z120-1-M119, edition 1
Resumen del contenido incluido en la página 11
MYRICA V40-1 Connections on LCD TV Observe the safety precautions in the "Important notes" chapter in this operating manual. ! Do not cover the ventilation openings of the monitor. Never open the housing of the power supply unit. There is extreme danger from an electrical shock with the housing open. There are no components requiring cleaning or repairs in the interior. 5 10 12 12 3 4 5 6 78 9 11 13 14 1 = RS-232 port 8 = SCART2 port (Full) 2 = DVI port 9 = S-VIDEO port 3 = AUD
Resumen del contenido incluido en la página 12
MYRICA V40-1 PC IN Connection for analogue VGA input signals (blue) e.g. for a PC with an analogue output (D-SUB) COMPONENT 1 Connections for component video and audio input signals COMPONENT 2 e.g. for HDTV decoder, HDTV video recorder or HDTV player Y - green Pb - blue Pr - red AUDIO white (left) red (right) SPEAKER Connection terminals for external loudspeakers red/right/+ black/right/- black/left/- red/left/+ SCART 1 Connection for AV (CVBS) and audio inp
Resumen del contenido incluido en la página 13
MYRICA V40-1 S-VIDEO IN Connection for S-VIDEO input signals e.g. for DVD player, video recorder or film camera with S- Video connection AV: Connections for video and audio input signals VIDEO e.g. for DVD player, video recorder, film camera with S-Video yellow connection or gaming console AUDIO white (left) red (right) TV-ANT. antenna cable port AC INPUT Connector for the power cable A26361-K1070-Z120-1-M119, edition 1 English - 11
Resumen del contenido incluido en la página 14
MYRICA V40-1 Connecting LCD TV Connecting antenna ► Connect an antenna cable to the antenna connection of the TV and to the TV antenna socket. Connecting the power supply ► Plug the power cable supplied into the power connector of the LCD TV. You will find the power connector on the back of the TV. ► Connect the connector of the power cable supplied into a properly earthed mains outlet and ensure a secure connection. 12 - English A26361-K1070-Z120-1-M119, edition 1
Resumen del contenido incluido en la página 15
MYRICA V40-1 Switching LCD TV on/off ► Press the ON/OFF switch at the left on the back of the TV. Switching LCD TV on/into standby mode ► Press the Standby button at the right on the underside of the TV. From the indicator at the lower right on the front of the LCD TV you can recognise whether the device is in operation, in the standby mode or switched off. Green = The device is switched on. Red = The device is in standby mode. Dark = The device is switched off.
Resumen del contenido incluido en la página 16
MYRICA V40-1 Setting language of the OSD menu After switching on the device, set the language of the OSD (On Screen Display) menu according to your needs. According to the country variant, either German or English is preset as the default setting. If you want to use a different language, change this setting with the OSD menu. ► Switch the LCD TV on with the ON/OFF switch. ► Press the POWER button. ► Press the MENU button to open the OSD menu. ► Choose the Setup menu item using the butt
Resumen del contenido incluido en la página 17
MYRICA V40-1 ► Select the Auto Scan menu item using the button. ► Press the MENU button to activate the menu item. ► Select your country with the button. ► Press the MENU button to start the programme search. Wait until the programme search is completed. Then the device shows the first programme found. The programmes will be entered in the programme list in the order in which they are found. However, you can change the order of the programmes later (see "Arranging i programmes")
Resumen del contenido incluido en la página 18
MYRICA V40-1 Arranging programmes With the OSD menu you can rearrange the order of the programmes according to your personal preferences. Moving programme ► Select the programme you want to move with the buttons / . ► Press the INSERT button (yellow) to mark the programme to be moved. ► Select the position at which you want to insert the programme with the buttons / . ► Press the INSERT button (yellow). The programme will be inserted at the selected position. Swapping position of two
Resumen del contenido incluido en la página 19
MYRICA V40-1 Setting channel of a programme This function is used when a programme is transmitted on a new station frequency. ► Select the programme for which you want to set another channel with the buttons / . ► Mark the property CH with the buttons / . ► Select the desired channel with the / buttons. Selecting TV standard ► Select the programme for which you want to set the TV standard with the buttons / . ► Mark the property Picture with the buttons / . ► Select the desired T
Resumen del contenido incluido en la página 20
MYRICA V40-1 Deleting program ► Select the programme you want to delete with the buttons / . ► Press the ERASE button (red). The selected programme is deleted from the programme list. Selecting signal source Selecting signal source for main display ► Press the SOURCE button in the upper section of the remote control. ► Choose the signal source you require using the button. ► Press the MENU button to activate your selection. Selecting signal source for PIP display ► Press the ON/OFF
