Resumen del contenido incluido en la página 1
GENUINE PARTS
iPOD INSTALLATION INSTRUCTIONS
1. DESCRIPTION: iPod
2. PART NUMBERS: iPod Gateway Module Kit (Nissan 2004-05) 999U7-VR000
iPod Gateway Module Kit (Infiniti 2004-05) 999U7-VR001
N-Bus harness for iPod Gateway 999U7-VS000
N-Bus harness for [optional] SAT Radio 999U7-VS001
3. MODEL APPLICATION: ARMADA, TITAN & QX56 (2004~5) w/ SAT Pre-wired N-Bus Harness
4. iPOD GATEWAY MODULE KIT CONTENTS (999U7-VR000/1):
No. Parts Qty Parts View
11 iPod Gateway Module
21 Cable tie (8") 2
36 Cable
Resumen del contenido incluido en la página 2
ARMADA, QX56 & TITAN 5. TOOLS & MATERIALS REQUIRED: 1. Phillips screwdriver (#2) 5. 1/8”, 11/16” drill bits 2. Electrical tape 6. ¼” driver w/ 8mm socket 3. Masking tape 7. Plastic Pry bar 4. Drill 8. PGF Stick PGF Stick 6. INSTALLATION OUTLINE: Vehicle Front iPod Gateway Module Satellite Radio 999U7-VS001 [optional] 999U7-VS000 [optional] SAT Pre-wired N-Bus harness Head Unit iPod (glove box) iPod cable Fig. 1 3.14.06 2/11 284-9798-100-I1
Resumen del contenido incluido en la página 3
ARMADA, QX56 & TITAN 7. VEHICLE PREPARATION: (1) Apply parking brake. (2) Record the customer radio presets. Bank 1234567 A B C (3) Make sure that the shift lever is engaged in the "P" position. (4) If equipped, move the accelerator and brake pedals to the front most position. (5) Turn the ignition switch OFF (6) Open engine hood. (7) Disconnect the battery negative terminal to prevent short circuits during installation. (8) Locate N-BUS harness on the speaker amplifier bracket. Fig. 2 Fig.
Resumen del contenido incluido en la página 4
ARMADA, QX56 & TITAN (9) Remove the following interior parts as shown in Fig. 2 (Refer to vehicle service manual) a) Instrument lower cover LH b) Instrument lower cover RH Glove Box assembly c) alignment pin b) a) clip points clip points alignment pin Instrument lower cover RH Instrument lower cover LH c) Glove Box assembly Fig. 3 3.14.06 4/11 284-9798-100-I1
Resumen del contenido incluido en la página 5
ARMADA, QX56 & 8. CABLE ROUTING (iPOD GATEWAY & [OPTIONAL: SATELLITE RADIO]): TITAN optional cable for SAT radio (1) Connect corresponding connector of the iPod gateway Front of Vehicle harness to the vehicle's prewired N-Bus. From vehicle's N-Bus prewired connector start by routing down to lower center console. Route cable on passenger side of (above) large harness near center console. [Optional: Connect corresponding connector of the Satellite harness to the correct tuner connec
Resumen del contenido incluido en la página 6
ARMADA, QX56 & TITAN Route cable(s) above small mounting Fig. 7 bracket for the glove box. (3) Before routing cable(s) into C-channel, route cable(s) behind and above small mounting bracket for the glove box. Route cable(s) up towards C-channel in the glove box's cavity. [Optional: Route Satellite cable in the same fashion.] Fig. 7 (4) If routing the satellite radio bus cable ensure that they Ensure cables are stacked are stacked vertically directly to the right of the glove verti
Resumen del contenido incluido en la página 7
ARMADA, QX56 & 9. CABLE ROUTING (iPOD CABLE): TITAN (1) Using a 1/8" bit, drill a pilot hole in the upper part of the Fig. 11 glove box 14mm +/-1mm (0.55in) from both front and right walls of the box. Then use an 11/16" drill bit to 14 mm open up the hole. Fig. 11 CAUTION Accurate measuring is important in this step due to possible interference issues with the iPod cable and the opening/closing of the glove box. glove box latch (2) Mark the iPod cable 762mm +/- 25mm (30in +/- 1in)
Resumen del contenido incluido en la página 8
ARMADA, QX56 & 10. iPOD GATEWAY MOUNTING: TITAN Fig. 15 (1) Connect all routed cables to the corresponding terminals of the iPod gateway. Fig. 15 (2) Thread the two (2) large cable ties through the holes in the chassis from left to right (label facing up). Ensure that the cable ties are pulled through with no slack and the head is pulled right up to module. Fig. 16 (3) Attach another two (2) large cable ties, one to each of the threaded cable ties from the previous step. Fig. 16 F
Resumen del contenido incluido en la página 9
ARMADA, QX56 & TITAN (7) Now the tape liner can be removed and the assembly Fig. 19 put into place. Fig 20 (8) Position the assembly just in front of and at equal height as the top of the hole in the metal frame. Apply equal pressure to the module for at least 20 seconds. After attaching to metal frame let the module sit for 5 minutes to ensure good adhesion before applying any shear pressure. Fig. 20 position at equal height and to Fig. 20 the front of these imaginary lines (9) Ti
Resumen del contenido incluido en la página 10
ARMADA, QX56 & TITAN 11. OPERATION CHECK: (1) Connect the battery negative terminal. (2) Turn vehicle ignition switch to the "ACC" position. Reference the vehicle specific Satellite Radio Installation Instructions for further information. If Satellite (3) radio was part of installation turn radio on then select satellite radio mode. Acquiring (Sirius) or Loading (XM) will display for a while. If not, move vehicle to outside and try again. If Satellite radio was part of installation tu
Resumen del contenido incluido en la página 11
NISSAN IPOD INTERFACE DIAGNOSTIC FLOW CHART 1. Verify iPod module is installed by looking in glove box for iPod cable. 2. Confirm the audio system is otherwise OK (AM/FM/CD works normally). Can SAT be selected on the audio system? Push the SAT button if present. If no SAT button, push “Radio”. NO YES “NO SAT” is shown on the audio display. Is an iPod connected? After pushing “Radio,” display says NO AM/FM/AM YES YES Does radio show: Connect iPod “RADIO ID” “NO IPOD”? Check connec
