Manual de instrucciones de Metra Electronics 99-8218

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS FOR PART 99-8218
APPLICATIONS
TOYOTA
CAMRY / CAMRY HYBRID
2007-2011
99-8218
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Radio Housing • B) Radio Housing Brackets • C) ISO Snap-In Brackets • D) Double DIN Brackets
E) Trim Plate • F) Double DIN Trim Plate • G) Pocket • H) (4) # 8 x 3/8 Phillips Screws • I) (4) #4 x 1/4 Phillips Screws
B
E

Resumen del contenido incluido en la página 2

99-8218 TABLE OF CONTENTS Dash Disassembly - Toyota Camry / Camry Hybrid 2007-2011 . . . . . . . . . . . . 1, 2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 3 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Final Assembly ..................................

Resumen del contenido incluido en la página 3

1 2 4 5 6 3 1 2 6 3 4 5 1 2 3 4 5 6 99-8218 DASH DISASSEMBLY TOYOTA CAMRY/CAMRY HYBRID 2007-2011 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Turn the shift knob counterclockwise to remove. 3 Unclip and remove (1) trim panel from each side of the pocket below the radio/climate control assembly. (2 panels total) (Figure A) B 4 Unclip and remove the shift knob trim panel. (Figure B) 5 Unclip and remove the top of the center console including the cup holde

Resumen del contenido incluido en la página 4

1 2 4 5 6 3 1 2 3 4 5 6 DASH DISASSEMBLY 99-8218 TOYOTA CAMRY / CAMRY HYBRID 2007-2011 A 8 Unclip and remove the A/C vents above the radio. (Take care not to scratch the dash panel. (Figure A) 9 Remove (2) 10mm bolts above the radio (behind the A/C vents) and (2) 10mm bolts below the climate controls (behind pocket) then unplug and remove the radio/climate control assembly. B (Figure B) 10 Remove the (10) Phillips screws securing the brackets to the radio/climate control assembly and separate t

Resumen del contenido incluido en la página 5

99-8218 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET A NOTE: Refer also to the instructions included with the aftermarket radio. Slide the DIN cage into the Radio 1 Housing and secure by bending the metal locking tabs down. (Figure A) B Slide the after-market radio into the 2 cage until it snaps into place. (Figure B) Snap the pocket into the radio 3 housing. (Figure B) Align the small legs on the bottom 4 C of the radio housing with the slots in the top of the climate control. Then slide the cl

Resumen del contenido incluido en la página 6

99-8218 KIT ASSEMBLY ISO RADIO PROVISION WITH POCKET A NOTE: Refer also to the instructions included with the aftermarket radio. Mount the ISO Brackets to the 1 radio with the screws supplied with the radio. (Figure A) Slide the radio into the radio open- 2 B ing until the side clips engage. (Figure B) Snap the Trim plate into the Radio 3 Housing. (Figure B) Snap the pocket into the radio 4 housing. (Figure B) Align the small legs on the bottom 5 C of the radio housing with the slots in the top

Resumen del contenido incluido en la página 7

99-8218 KIT ASSEMBLY DOUBLE DIN A RADIO PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Cut and remove center divider 1 from radio housing. (Figure A) B Snap the Double DIN brackets to the 2 inside edge of the radio housing. (Figure B) Slide the Double DIN radio into the 3 Double DIN bracket/radio housing assembly and secure the radio to the C assembly using the screws supplied with the radio. (Figure C) Snap the Double DIN trim-plate into 4 the housing/radio

Resumen del contenido incluido en la página 8

99-8218 KIT ASSEMBLY STACKED ISO A UNITS PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Cut and remove center divider 1 from radio housing. (Figure A) B Snap the Double DIN brackets to the 2 inside edge of the radio housing. (Figure B) Slide the Stacked ISO units into the 3 Double DIN bracket/radio housing assembly and secure the radio to the C assembly using the screws supplied with the units. (Figure C) Snap the Double DIN trim-plate into 4 the housing/rad

Resumen del contenido incluido en la página 9

99-8218 FINAL ASSEMBLY FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassem

Resumen del contenido incluido en la página 10

99-8218 NOTES 8

Resumen del contenido incluido en la página 11

99-8218 NOTES 9

Resumen del contenido incluido en la página 12

99-8218 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 07-22-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8218