Manual de instrucciones de Metra Electronics 99-7877S

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS FOR PART 99-7877S
APPLICATIONS
Honda Fit 2009-10
99-7877S
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
“S”= SILVER
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
C
B
D
A
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-1729 Honda Ha

Resumen del contenido incluido en la página 2

99-7877S TABLE OF CONTENTS Dash Disassembly - Honda Fit 2009-10 . ... ... .... ... .... ... .... ... . . . . . . 1 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio/ Stacked ISO Mount Units Provision . . . . . . . . . . . . . 5 *Not

Resumen del contenido incluido en la página 3

99-7877S DASH DISASSEMBLY HONDA FIT 2009-10 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Unclip and remove the lower center panel below radio. (Figure A) 3 Remove (1) 8 MM bolt facing up behind center panel. Note: Slide the recirculation control lever to FRESH for better access to bolt. (Figure A) 4 Open the upper glove box then use a pry tool to unclip and remove the B radio/climate control assembly. (Figure B & C) 5 Remove (2) Phillips screws securi

Resumen del contenido incluido en la página 4

99-7877S KIT PREPARATION KIT PREPARATION 1 Secure the hazard switch into the A radio housing panel using the factory hardware. (Figure A) 2 Secure the air bag light into the radio housing panel using the factory hardware. (Figure A) 3 Secure the a/c vents to the radio housing using the factory hardware. (Figure B) 4 Attach the (7) retaining clips to the radio housing panel in the same location as removed from the factory B radio panel. Continue to kit assembly. 2

Resumen del contenido incluido en la página 5

99-7877S KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Slide the aftermarket head unit into the cage and sec

Resumen del contenido incluido en la página 6

99-7877S KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Slide the head unit into the radio opening until the side clips eng

Resumen del contenido incluido en la página 7

99-7877S KIT ASSEMBLY DOUBLE DIN RADIO PROVISION/ STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing. (Figure A) 3 Snap the Double DIN brackets to the inside edge of the Radio Housing.

Resumen del contenido incluido en la página 8

99-7877S INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 4/22/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7877