Manual de instrucciones de Metra Electronics 99-7402

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS FOR PART 99-7402
APPLICATIONS
Nissan
350Z 2003-2005
99-7402
KIT FEATURES
• DIN Radio Provision with pocket
• ISO Radio Provision with pocket
• Two stacked ISO units provision
• Double DIN radio provision
KIT COMPONENTS
A) Radio Housing with Pocket B) Double DIN Trim-plate C) ISO Spacer Brackets D) ISO Snap-in Brackets E) ISO Trim-plate
A
B C D
E
TOOLS REQUIRED:
Panel Removal Tool or
Phillips Screwdriver
Small Flat Blade Screwdriver
1-800-221-0932 www

Resumen del contenido incluido en la página 2

99-7402 TABLE OF CONTENTS Dash Disassembly Nissan 350Z 2003-2005....................................1, 2 Kit Assembly Din Mount Radio Provision with pocket..........................................................3 ISO Mount Radio Provision with pocket..........................................................4 Double DIN Radio..............................................................................................5 Two Stacked ISO mount units...............................................

Resumen del contenido incluido en la página 3

99-7402 DASH DISASSEMBLY NISSAN 350Z 2003-2005 Disconnect the negative battery 1 A terminal to prevent an accidental short circuit. 2 For vehicles with automatic trans- mission, Unsnap and remove smaller trim-ring from around shifter. (Figure A) For vehicles with manual transmis- B sion, Unscrew and remove shifter knob. (Figure A) 3 Unsnap and remove center console trim panel including climate controls. (Figure B) C 4 For vehicles with navigation, Unsnap and remove navigation switch panel.

Resumen del contenido incluido en la página 4

DASH DISASSEMBLY 99-7402 NISSAN 350Z 2003-2005 6 Remove (2) screws above the radio E and (2) screws below the radio. Also remove (2) screws securing the radio/trim panel assembly. (Figure E) 7 Unplug and remove the radio / trim panel assembly. (Figure F) F 8 Remove (4) screws securing the radio to the trim panel and remove the radio. 9 Remove (8) screws securing the factory brackets to the radio and remove the brackets from the radio. (These brackets are required for stacked ISO and double DI

Resumen del contenido incluido en la página 5

KIT ASSEMBLY 99-7402 DIN MOUNT RADIO PROVISION WITH POCKET A 1 Slide DIN cage (supplied with radio) into the radio housing from the front. (Figure A) 2 Secure DIN cage to radio housing by bending the locking tabs outward. (Figure A) B 3 Slide the radio into the DIN cage until it snaps into place. (Figure B) Attach the radio / housing assembly 4 C to the radio trim panel using the factory screws removed during disassembly. (Figure C) Continue to final assembly. 3

Resumen del contenido incluido en la página 6

KIT ASSEMBLY 99-7402 ISO MOUNT RADIO WITH POCKET A 1 Align the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio bracket assembly into B the radio housing until it snaps into place. (Figure B) 3 Snap the ISO trim-plate onto the front of the assembled radio and housing. (Figure B) C 4 Attach the radio / housing assembly to the radio trim panel using the factory screws removed during disassembl

Resumen del contenido incluido en la página 7

KIT ASSEMBLY 99-7402 DOUBLE DIN RADIO 1 Cut and remove center divider from A double DIN trim-plate. (Figure A) 2 Place the double DIN trim-plate on the front of the radio. (Figure B) 3 Place one of the ISO spacer brackets and the right factory mounting bracket (Removed from radio during disassembly) on the right side of the radio. (The spacer bracket should be between the radio and the factory bracket.) Align the pins on the trim- B plate with the holes on the factory bracket and mount the fact

Resumen del contenido incluido en la página 8

KIT ASSEMBLY 99-7402 TWO STACKED ISO MOUNT UNITS 1 Place the double DIN trim-plate on A the front of the two ISO units. (Figure A) 2 Place one of the ISO spacer brackets and the right factory mounting bracket (Removed from radio during disassembly) on the right side of the ISO units. (The spacer bracket should be between the ISO units and the factory bracket.) Align the pins on the trim-plate with the holes on the factory bracket and mount the factory bracket to the ISO units using screws suppl

Resumen del contenido incluido en la página 9

FINAL ASSEMBLY 99-7402 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring

Resumen del contenido incluido en la página 10

99-7402 NOTES 8

Resumen del contenido incluido en la página 11

99-7402 NOTES 9

Resumen del contenido incluido en la página 12

99-7402 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7402 REV. 05/05/06