Manual de instrucciones de Metra Electronics 99-5816

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS FOR PART 99-5816
APPLICATIONS
FORD Focus
2008-2011
99-5816
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle Radio Housing Clips
D E
B C
A
SIDE VIEW SIDE VIEW

Resumen del contenido incluido en la página 2

99-5816 TABLE OF CONTENTS Dash Disassembly - Ford Focus 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1,2 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .5 - Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . .

Resumen del contenido incluido en la página 3

PASS AIRBAG OFF PASS AIRBAG OFF PASS AIRBAG OFF 95-5816 DASH DISASSEMBLY FORD FOCUS 2008-2011 A 1 Disconnect the negative battery termi- nal to prevent an accidental short cir- cuit. 2 Unclip and remove the trim panel sur- rounding the shifter and including the cup holders. (Figure A) 3 Remove (2) 9/32” screws from the bot- tom edge of the factory radio trim panel. (Figure B) 4 Remove (2) 9/32” screws facing up above the gauge cluster then unclip B and remove the trim panel

Resumen del contenido incluido en la página 4

95-5816 DASH DISASSEMBLY FORD FOCUS 2008-2011 6 Unclip and remove the vent panel at E the top of the factory radio trim panel. (Figure E) 7 Remove (2) 9/32” screws behind the vent panel removed in step 6. (Figure F) 8 Unclip the factory radio trim panel assembly. Unplug and remove the assembly. Note: Some early models had a ground strap attached to the radio chassis and the sub dash with an 8 MM bolt. You will need to unbolt this strap to remove the factory radio trim panel assembly. 9 Re

Resumen del contenido incluido en la página 5

99-5816 KIT ASSEMBLY KIT PREPARATION A 1 Secure the climate control into the radio housing using the factory hard- ware. (Figure A) 2 Secure the accessory socket panel to the radio housing using the factory hardware. (Figure B) 3 Clip the passenger air bag light and the switch panel blank plates in to the radio housing. (Figure C) 4 Attach Top and Middle Radio Housing Clips to the back of the radio housing. (Figure D,E) B NOTE: When the clips are properly attached they should be on a 90 degree a

Resumen del contenido incluido en la página 6

99-5816 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio hous- ing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage and until it snaps into place. 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 4

Resumen del contenido incluido en la página 7

99-5816 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Mount the ISO Brackets to the radio A using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) 4 Snap the Pocket into the radio housing. (Figure C) B Continue to final assembly. C 5

Resumen del contenido incluido en la página 8

99-5816 KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the center bar from A the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) B 4 Snap th

Resumen del contenido incluido en la página 9

99-5816 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Resumen del contenido incluido en la página 10

99-5816 NOTES 8

Resumen del contenido incluido en la página 11

99-5816 NOTES 9

Resumen del contenido incluido en la página 12

99-5816 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 11/18/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-5816