Resumen del contenido incluido en la página 1
ELX8-60
Installation Guide
(v 1.0a)
Resumen del contenido incluido en la página 2
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This eq
Resumen del contenido incluido en la página 3
Important Notice 1. Do not place heavy objects on the top of the ELX8-60. 2. ELX8-60 is not weatherproof. In case of outdoor use, equip a weatherproof case to protect ELX8-60 from water, moisture, or temperature (higher or lower than specificat ions). To clean the ELX8 -60, gently wipe the outside with a clean dry cloth. 3. Be sure to use a DC adapter that is provided by Rugged CCTV Connecting ELX8-60 directly to an AC current will cause electric damages to ELX8-60. 4. Be care
Resumen del contenido incluido en la página 4
ELX8 -60 TABLE OF CONTENTS OVERVIEW ..................................................................................................................................................................7 1. What is ELX8-60?.........................................................................................................................................7 2. Supplied Accessories ...................................................................................................................
Resumen del contenido incluido en la página 5
TABLE OF CONTENTS ELX8 -60 8.3. Setting Recording Condition .........................................................................................................24 8.3.1. Configuration Status................................................................................................................25 8.3.2. Channel Status.......................................................................................................................... 25 8.3.3. Recording Speed/Quality..........
Resumen del contenido incluido en la página 6
ELX8 -60 TABLE OF CONTENTS 16.3. Uninstalling DVR Manager ........................................................................................................43 16.4. Configstation..................................................................................................................................43 16.5. Monitor..............................................................................................................................................44 16.6. Playback .......
Resumen del contenido incluido en la página 7
OVERVIEW ELX8 -60 OVERVIEW 1. What is ELX8-60? The ELX8-60 is an 8-analog channels network digital video recorder. Video, Audio, and Text Event-Logs are digitized and stored on two internal hard-drives. Key features q 8 analog video channels q 1 channel audio recording & playback q Max. 60 / 50 ips (NTSC / PAL) recording speed q Realtime (30 / 25 ips for each channel) monitoring q Built-in software multiplexer for all 8 live monitoring channels (1 / 4 / 9 Ch Mode on CCTV Mon
Resumen del contenido incluido en la página 8
ELX8 -60 OVERVIEW 2. Supplied Accessories Unpack and check all the items as below. 1. ELX8-60 (1) 2. DC Power Supply (1) (110V~220V) 3. AC Power Cord (1) 4. CD-ROM (Including DVR Manager) (1) 5. Remote Controller (1) 6. Guide (2) 7. Plug Bracket (1) 8. HDD Fixing Screw (8) 8 2003. 08. 13 (v 1.0) Rugged CCTV
Resumen del contenido incluido en la página 9
OVERVIEW ELX8 -60 3. Description & Function ELX8-60 Front (1) LED (2) IEEE1394 connecter (3) Remote controller receiver (4) USB connecter (5) Function buttons (6) Bracket fixing hole for rack mount Rugged CCTV 2003. 08. 13 (v 1.0) 9
Resumen del contenido incluido en la página 10
ELX8 -60 OVERVIEW ELX8-60 Rear (7) Power switch (8) Ethernet connector (9) BNC connector for Video input (10) Audio input / output connector (11) RS232 connecter (9Pin D-Sub) (12) Terminal block for RS232 & 422/485 (13) Terminal block for Sensor input (14) Terminal block for Relay output (15) Video output for MONITOR or VCR (16) Video input type/impedance select & remote controller switch (17) IEEE1394 connecter (18) USB connecter (19) Power connector (DC12V) (20) GND 1
Resumen del contenido incluido en la página 11
INSTALLATION AND CONNECTION ELX8 -60 INSTALLATION AND CONNECTION 4. Connecting & Running ELX8-60 4.1. Connecting camera (1) Set video type (NTSC/PAL) by rear panel ’s switch. (2) Connect CCTV camera to ELX8-60 with BNC cable as shown below. The video type for all channels should be either NTSC or PAL. NTSC is the standard used in North America. Rugged CCTV 2003. 08. 13 (v 1.0) 11
Resumen del contenido incluido en la página 12
ELX8 -60 INSTALLATION AND CONNECTION 4.2. Connecting Monitor (1) Connect CCTV monitor to ELX8-60 with BNC cable as shown below. ELX8-60 has two video output ports ; for Monitor and VCR. The output signals from the two ports are same and either port may be used. 4.3. Connecting Audio (1) Connect audio signal to ELX8 -60. 12 2003. 08. 13 (v 1.0) Rugged CCTV
Resumen del contenido incluido en la página 13
INSTALLATION AND CONNECTION ELX8 -60 4.4. Supplying Power (1) Connect power cable to ELX8 -60. (2) Turn on the power switch located on the ELX8-60 rear panel. Use the plug bracket to secure the power cable if needed. To connect EARTH, refer to the following picture. Rugged CCTV 2003. 08. 13 (v 1.0) 13
Resumen del contenido incluido en la página 14
ELX8 -60 INSTALLATION AND CONNECTION 5. Running OSD menu 5.1. Using menu Press the [MENU] button to open the OSD Configuration Menu. (1) Main Menu (2) Sub-menu (3) Setting Page (4) Help message (1) Main Menu Tabs: The select ed tab is shown in blue and the related sub-menus will be shown below the tab. To move to the previous/next Main Menu Tab, use the [ / ] arrow buttons. To move to a sub-menu, press the [ENTER] or [ ] buttons. (2) Sub-menu: The select ed sub -menu
Resumen del contenido incluido en la página 15
INSTALLATION AND CONNECTION ELX8 -60 5.2. Dialogue Box to Edit a Word There are two methods to set word. (1) Using number button “ ” Enter the related numbers in order of horizontal/vertical . (For example, in order to select C , press [3] and [2] buttons.) (2) Using arrow button Select a value using the [ / ] or [ / ] buttons. The intersection of the horizontal and vertical bar is select ed value. Press the [ ] button to confirm the selected value. Rugged CCTV 200
Resumen del contenido incluido en la página 16
ELX8 -60 INSTALLATION AND CONNECTION (3) Function word The following symbols are for executing specific functions: ü 1#2.1 : Enter : Back Space & delete : Space : Move to left : Move to right : Previous Code Page : Next Code Page 16 2003. 08. 13 (v 1.0) Rugged CCTV
Resumen del contenido incluido en la página 17
INSTALLATION AND CONNECTION ELX8 -60 6. Setting remote controller 6.1. Setting remote control DIP switch Set the remote control DIP switch to “ON.” 6.2. Setting ID of ELX8-60 When controlling sever al ELX8-60s with one remote controller, set Remote Control ID as follows. (1) Press the [MENU] button. (2) Select “System” with using [ ] button and press the [ENETR] or [ ] button. (3) Select “Miscellaneous” from the sub-menu list using the [ ] button and press the [ENETR] butto
Resumen del contenido incluido en la página 18
ELX8 -60 INSTALLATION AND CONNECTION (4) Select “Remote Control ID,” and press the [ENETR] button. (5) Select a value using the [ / ] buttons and press the [EXIT] button. (6) Press the [EXIT] button to exit the Settings Page and return to Monitor mode. Remote Control ID Up to 16 ELX8-60s can be controlled with a single remote controller. 6.3. Selecting ELX8-60 If several ELX8-60s are set with unique ID numbers, they can be controlled with one remote controller. To
Resumen del contenido incluido en la página 19
INSTALLATION AND CONNECTION ELX8 -60 6.5. Loading the batteries into remote controller Remote controller requires two AAA-type batteries. 2. Taking care that the poles(+/-) 1. Remove the battery cover. 3. Replace the battery cover. are correctly positioned Batteries are not included as a packing accessory. Rugged CCTV 2003. 08. 13 (v 1.0) 19
Resumen del contenido incluido en la página 20
ELX8 -60 INSTALLATION AND CONNECTION 7. ELX8-60 Configuration 7.1. Basic Configuration 7.2. Advanced Configuration 20 2003. 08. 13 (v 1.0) Rugged CCTV
