Resumen del contenido incluido en la página 1
3-855-576-15(1)
DVD Recorder
Instructions For Use
DVO-1000MD
© 2005 Sony Corporation
Resumen del contenido incluido en la página 2
3. The leakage current could increase when connected Owner's Record to other equipment. The model and serial numbers are located at the rear. 4. This equipment generates, uses, and can radiate radio Record these numbers in the space provided below. frequency energy. If it is not installed and used in Refer to these numbers whenever you call upon your accordance with the instruction manual, it may cause Sony dealer regarding this product. interference to other equipment. If this unit causes
Resumen del contenido incluido en la página 3
You are cautioned that any changes or modifications not Caution expressly approved in this manual could void your Use of controls or adjustments or performance of authority to operate this equipment. procedures other than those specified herein may result in hazardous radiation exposure. All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. If you have any questions about this
Resumen del contenido incluido en la página 4
Repeat) ............................................................36 Repeat Playback of a Chapter ...........................38 Table of Contents Repeat Playback of a Title ................................38 Playing From the TITLE LIST Display ............39 Precautions ............................................................. 5 Verifying Information on a Disc .........................40 Copyrights .............................................................. 6 Viewing Frozen Pictures ...
Resumen del contenido incluido en la página 5
On the panel display: HUMID! Precautions When the disc is being loaded in the unit If you give a violent shock to the unit or move it with a On safety disc loaded because the unit is recording or playing Should any liquid or solid object fall into the cabinet, back, the disc may be damaged. Be sure to remove a disc unplug the unit and have it checked by qualified before moving the unit. personnel before operating it further. Unplug the unit from the wall outlet if it is not to be On c
Resumen del contenido incluido en la página 6
Copyrights Materials played or recorded on this unit may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. You cannot use those materials without permission from the owners except for playing those materials for personal use. This unit incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Mac
Resumen del contenido incluido en la página 7
Overview Title list Overview You can display the list of titles recorded on the disc, and using this list, you can search for the desired title from which you can start playback on the list. Variety of input/output interfaces Features Digital interfaces The DVO-1000MD is a DVD Recorder designed for use 1) This unit is equipped with an i.LINK connector so that with video equipment such as external equipment. The DV format digital video and audio signals can be input. DVO-1000MD compresses
Resumen del contenido incluido en la página 8
Overview Location and Function of Parts Front Panel 1 1 (Power) switch and standby indicator 2 Disc tray 3 OPEN/CLOSE button 7 Disc control section 8 Menu/disc control section 6 Front panel display 5 REMOTE 2 connector 4 REMOTE 1 connector 1 1 (power) switch and standby indicator 4 REMOTE 1 connector (stereo mini jack) Press to power on the unit when the MAIN POWER Connect a SVRM-100A remote control unit (not switch (see page 11) on the rear panel is turned on. supplied) to this connector for r
Resumen del contenido incluido en la página 9
Overview 6 Front panel display F TITLE indicator Indicates the number of the title which is being recorded or played back. A Disc indicator G CHAP (chapter) indicator B Recording mode indicator Indicates the number of the chapter which is being C INPUT signal indicator recorded or played back. D Dolby indicator H Time indicator E REPEAT indicator In normal operation, the elapsed time is displayed. F TITLE indicator While recording, the elapsed time or the remaining G CHAP indicator time of t
Resumen del contenido incluido en la página 10
Overview UP: Used to go back to the previous page during Press this button to display the menu on the monitor title operation in the TITLE LIST display. screen and the front panel display. Press it again to exit the menu display. C BPLAY button When you press this button, it lights and playback B LIST button begins. Press this button to display the TITLE LIST menu. D >NEXT/DOWN button C SET button NEXT: Used to jump to a chapter. Press this button to save new settings, such as When pressed o
Resumen del contenido incluido en la página 11
Overview Rear Panel 2 S-VIDEO IN connectors 3 VIDEO IN connectors 4 VIDEO OUT connector 1 MAIN POWER switch 5 S-VIDEO OUT connector 6 MONITOR AUDIO connector qd -AC IN connector 7 AUDIO OUT L/R connectors 8 AUDIO IN L/R connectors 9 REMOTE IN RS-232C connector 0 DV IN (i.LINK) connector qa USB connector qs Equipotential ground terminal connector 1 MAIN POWER switch ). Thus the same signals which are input to the Switch to the = side to turn the power on. Switch to left connector are output fro
Resumen del contenido incluido en la página 12
Overview Use this connector to control this unit by connecting it to equipment such as an external equipment which supports the RS-232C interface. 0 DV IN (i.LINK) connector (6-pin) This connector inputs digital video signals conforming to the i.LINK protocol. Also, this connector is used to control this unit by connecting it to equipment such as an external equipment which supports i.LINK. qa USB connector This connector is used to control this unit by connecting it to equipment such as a
Resumen del contenido incluido en la página 13
Overview Connection Connect the AC power cord last. Notes Before making connections, be sure to turn the power of any peripheral equipment off. Connecting External Equipment (1) This section gives a connection example to operate the – LCH: Outputs the audio signal of audio channel 1. unit connected to external equipment using a remote – RCH: Outputs the audio signal of audio channel 2. control unit (not supplied) and/or foot switch (not – MIX: Outputs a mixed audio signal from both supplie
Resumen del contenido incluido en la página 14
Overview Connecting External Equipment (2) This section gives an example to connect external – RCH: Outputs the audio signal of audio channel 2. equipment for controlling the unit from connected – MIX: Outputs a mixed audio signal from both external equipment channel 1 and channel 2. (factory setting) Input signal selection Settings required for using this connection Select the input signal “ANALOG” using the INPUT example SELECT sub menu of SETUP MENU (see page 24). Make the following set
Resumen del contenido incluido en la página 15
Overview 1 Push the 1 (power) switch on the front panel to put the unit in the standby mode. Turning the Power On/ 2 Set the MAIN POWER switch on the rear panel to Off the z (off) side. The standby indicator on the front panel goes off Turning the Power On and the power is turned off. Rear panel 1 AC power cord (to AC outlet) Front panel Standby indicator 2 1 Connect the AC power cord (not supplied) to the wall outlet, and then set the MAIN POWER switch located on the rear panel to the [ (o
Resumen del contenido incluido en la página 16
Overview Select the proper video signal system corresponding to the one used in your area. Setup Preparation Before you start to use the unit after you have made the 10 required connections, it is necessary to perform the 11,12 1 following operations. Selecting either NTSC or PAL video signal system Select the video signal system used in your region. For detailed information, see “Selecting Either NTSC or PAL Video Signal System” (page 16). Setting the date and time You should set the dat
Resumen del contenido incluido en la página 17
Overview The SETUP MENU appears. The following display appears when enhanced menu items have been added under the last item of the basic setup menu. 4 Select “MENU GRADE” from the SETUP MENU display. 7 Select “TV SYSTEM” by pressing the v button. Each time you press the v or V button, the highlighted cursor moves down or up item by item. When the highlighted cursor reaches the last item “KEY INHIBIT,” press the v button again. The next page of the SETUP MENU appears. Press the v button se
Resumen del contenido incluido en la página 18
Overview The message “NOW SAVING....” appears and the The TOP menu appears. unit starts to save the setting. When saving is completed, the message disappears. Then, “TV SYSTEM WAS CHANGED PLEASE POWER OFF.” appears on the monitor display, and “POWER OFF!” appears on the front panel display. Note The TV system is not changed even if you push the SET button. Be sure to turn the power of the unit off and on as described in steps 11 and 12 to change the system. 2 Select “SETUP MENU” by pressin
Resumen del contenido incluido en la página 19
Overview Press the v button several times until “DATE/TIME you press the B button, the rightmost digit of the PRESET” is highlighted. date column is highlighted. Front panel display during menu operation The date column appears when you set the date in the date column on the DATE/TIME PRESET sub menu. And the time column appears when you set the time in the time column. 7 Change the numeric value by pressing the V or v button. Press the V button to increase a value. Press the v button to d
Resumen del contenido incluido en la página 20
Overview The SETUP MENU appears. Selecting the Remote Interface The REMOTE I/F sub menu of the SETUP MENU allows you to select the interface to be used to control the unit remotely. The factory setting is RS-232C. 7 1 4 Select “REMOTE I/F” by pressing the v button. 3,5 2,4,6 1 Press the MENU button. The TOP menu appears. 5 Press the b button. The REMOTE I/F sub menu appears. 2 Select “SETUP MENU” by pressing the V or v button. 6 Select the desired remote interface by pressing the “SETUP MENU
