Resumen del contenido incluido en la página 1
OWNER'S MANUAL
Water Softeners
With High Performance Valve
MODEL NOS.
IntelliSoft 370 Series 625.383760
IntelliSoft 370 Series 625.393760
Caution:
• Warranty
Read and follow all safety rules and operating
° Installation
instructions before first use of this product.
° Start Up / Setting Timer
Questions ?
° How ItWorks
Visit www.KenmoreWater.com
• Care Of
or call toll free 1-800-426-9345 (M - F,7AM - 8 PM CST)
Repair or Parts ? Call toll free 1-800.469-4663 ° Specifications
See back cover for oth
Resumen del contenido incluido en la página 2
WARRANTY ON WATER SOFTENER ONE YEAR LIMITED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore appliance fails due to a defect in material and workmanship within one year from the date of pur- chase, call 1-800-4-MY-HOME ®to arrange for free repair. THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS When installed, operated and maintained according to all instructions supplied with the product, if any of the fo
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Safety Guides ................................................................................................................................................. 4 Unpack and Check Shipment ........................................................................................................................ 5 Plan Your Installation: Tools Needed, Materials Needed ........................................................................... 6-10 Install Inlet/Outlet Adapters or By
Resumen del contenido incluido en la página 4
Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener. Your Kenmore Water Softener will remove hardness minerals from water. This is measured in grains per gallon (gpg). It will also remove some clear water iron*. This is measured in parts per million
Resumen del contenido incluido en la página 5
INSPECTSHIPMENT Your water softener is shipped complete in one carton. Use care when handling the softener. DO NOT turn upside down. DO NOT drop, or set on sharp objects that could make a hole in the bottom. The water softener is heavy, do not try to lift it or move more than is necessary. Remove all items from your shipping carton. Check all items against the packing list below. Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded view and pa
Resumen del contenido incluido en la página 6
PLAN YOUR INSTALLATION It is recommended to read through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system. TOOLS NEEDED: • Safety glasses • Flathead screw driver • Phillips screw driver • Adjustable slip joint pliers • Tape measure or ruler J Flathead Screwdriver Safety Glasses Phillips Screwdriver Adjustable Slip Joint Pliers Tape Measure or Ruler ADDITIONAL TOOLS NEEDED FOR THE FOLLOWING
Resumen del contenido incluido en la página 7
outside faucet (hard water) - outside faucet (hard water) soft, cold _ _ toR.O, faucet water ._,_ _ _ Hard _,_ ,_ ¢-- _- SOwf_th I Shut-off [_- II toR ...... i . -Valve II R.O. wa!er I _____ tank J I IIII1 house // water /4 gap _ softener / . _ floor mare " • shutof drain valve FIG. 3 Typical Installation WHERE TO INSTALL THE WATER SOFTENER Review the following points before you choose a place to put your softener. 1. Pl
Resumen del contenido incluido en la página 8
Suggested Slab Foundation Installation outside - hard water heater kitchen Plug the softener transformer bathroom into an inside, 120 volt 60Hz electrical outlet. If an outside outside For outside hard outlet is used, be sure it has -soft water, trench under- approved weather protection. ground as needed. outside € " " bypass - hard " valve outside -soft WATER SOFTENER (install in garage, car port, or other sheltered area) water in Run drain tubing to laundry tub or p-trap inside home, if possib
Resumen del contenido incluido en la página 9
PIPE, FITTINGS, OTHER MATERIALS NEEDED You must first decide how to run "in" and "out" pipes to the softener. Look at your house main water pipe at the OUT IN point you will connect the softener. Is the pipe soldered copper, glued plastic, or threaded galvanized or brass? 1" NPT sweat Use teflon tape, What is the pipe size? What kind of pipe and fittings is it adaptor (2)* pipe easiest for you to work with, and what tools do you have? or both. 1" NPT adaptor 2 of each Now look at the common plan
Resumen del contenido incluido en la página 10
BEFORE INSTALLING CHECKS & TESTS If you have a well water system, look at the pressure Your water supply needs to be checked for chemical gauge to find the water pressure. Call your local water analysis, water pressure and water flow rate. To accom- department if you have city water. They will tell you what plish this, complete the following steps: the water pressure is where you live. Check Water's Chemical Analysis: Sears sells a com- NOTE: Add these readings to the Facts and Figure plete line
Resumen del contenido incluido en la página 11
ASSEMBLE INLET OUTLET ADAPTORS, Shutoff Shutoff . Pressure OR SINGLE BYPASS VALVE Valve Valve L/Tank Complete the following steps to assemble the adaptors or bypass valve. 1. Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7. Pump 2. Shut off the gas or electric supply to the water heater. See Fig. 7. 3. Open the highest and lowest water faucets in your Electrical Panel house. This will let water drain from the pipes. C
Resumen del contenido incluido en la página 12
INSTALLING HOLDING CLIPS Black Clip Cross Section of Valve Inlet or Outlet Bypass Valve or Installation Adaptor Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port. Turbine Support Sensor Port O-Ring Clip Snaps into Place Between Larger Diameter Rings FIG. 11 BYPASS VALVE TURNED DOWNWARD Turbine FIG. 10 Turn bypass valve upside down to connect to floor level plumbing. FIG. 12 3 VALVE BYPASS INSTALLING 3 VALVE BYPASS AND
Resumen del contenido incluido en la página 13
POSITION SOFTENER INTO PLACE Complete the following steps to position the softener. MOVE SOFTENER INTO PLACE 1. Grip under the ridge on the salt tank sidewall. 2. Carefully rock back and forth into position. 3. Move the softener into position. 4. Place on a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the Grip under ridge II tank. Then put spacers under the plywood to level the to move softener. softener. See Fig. 14. NOTE: Do not put shims or space
Resumen del contenido incluido en la página 14
CONNECT THE VALVE DRAIN HOSE per tube is also best to use for an overhead drain. Use a copper drain tube if the softener is installed outside, Take a length of 3/8" inside diameter drain tubing and or in the sunlight. Heat from the sun can soften, flatten attach one end to the drain fitting. See Fig. 16. Use a and close up some kinds of tubes. tube clamp to hold it in place. Put the other end of the tubing over a floor drain, into a laundry tub, standpipe, To adapt a copper drain tube to the sof
Resumen del contenido incluido en la página 15
LEAK TEST To check for leaks, complete the following steps: HOUSE MAIN WATER SHUTOFF VALVES CAUTION: To avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be Shu_ sure to do the following steps exactly as instructed. Water ¢--_:h _ Pressure Tank 1. Fully open two cold, soft water faucets near the softener. Meter Shutoff _ Valve / "1"- 2. Look at the pictures in Fig. 18 and 19 to deter- Well Pump mine your kind of bypass va
Resumen del contenido incluido en la página 16
INSTALLGROUNDINGCLAMPBETWEEN COLD WATER PIPE GROUNDING THESOFTENERINAND OUT PIPES The house cold water pipe (iron or copper) is often TO Valve Inlet used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when Ground you touch any electric appliance plugged into the out- let. If you installed the single bypass valve, the cold Clamp (2% water pipe ground is broken. See Fig. 20 and 21. IMPORTANT: Be sure the cold water pipe has direct metal to metal contac
Resumen del contenido incluido en la página 17
INSTALLCOVERS Salt Hole After installing your water softener, replace the covers. Angle Cover Cover the covers so the main cover clips onto the back first, then (Main) bring down in front and clip on the two (2) tabs inside the rim of the salt hole and lower the salt cover closed. See Fig. 23. RESTART THE WATER HEATER Turn on the gas (or electric) supply to the water heater and light the pilot. YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE. FIG. 23 REGENERATION Button Salt Leve
Resumen del contenido incluido en la página 18
SET PRESENT TIME OF DAY U,I-I I-I PM ILl, 70 I'UU If the words PRESENT TIME do not show in the display, PRESENT TIME PRESENT TIME press the SELECT1 button until they do show in the dis- play. Press the UP or DOWN buttons to set the present 11 time. Press UP to move the display ahead; press DOWN to move the time backward. If the present time is between FIG. 26 noon and midnight, be sure PM shows. If the present time is between midnight and noon, be sure AM shows. Each press of the UP or DOWN butt
Resumen del contenido incluido en la página 19
SANITIZE THE WATER SOFTENER Salt Hole Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, or cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. SANITIZE YOUR WATER SOFTENER AS FOLLOWS: 1. Be certain the bypass valve is pulled out to Brinewell Cover "service" position. 2. Liftthe salt hole cover and using a p
Resumen del contenido incluido en la página 20
ADDINGSALTTOTHE STORAGETANK Brine(saltdissolved inwater)isneeded foreachand everyregeneration. Thewaterformaking brineis metered intothesaltstoragetankbythesoftener. You mustkeepsaltinthetank,butbecause thewatersoften- erisveryefficient, itis notnecessary to keepitfull. Especiallyin humidareas,it isbesttofill thestorage tankonequarter to onehalffull,andtoaddsaltmore often.Saltbridging occursmoreoftenwhenconditions arehumid. UseNUGGET orPELLET watersoftener salt.DONOT userocksalts,astheyhavedirta
