Resumen del contenido incluido en la página 1
INSTRUCTION MANUAL
One H.P. Single-Stage
Dust Collector
(Model 50-775)
PART NO. 902116 (015)
Copyright © 2001 Delta Machinery
To learn more about DELTA MACHINERY
SPANISH: PAGE 13
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Resumen del contenido incluido en la página 2
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY RULES FOR DUST COLLECTORS 10. DO NOT handle the plug or dust collector with wet WARNING: Basic precautions hands. should always be followed when using your dust collector.To reduce the risk of injury, electrical 11. REPLACE a damaged cord immediately. DO NOT shock or fire, comply with the safety rules listed use a damaged cord or plug. If the dust collector is not below: operating properly, or has been damaged, left outdoors or has been in contact with water, take it to an 1. DO
Resumen del contenido incluido en la página 4
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. 5 6 2 1 10 14 11 13 3 12 7 15 8 4 9 Fig. 2 1. Motor and blower assembly 9. Filter bag hanger 2. Base 10. Hose
Resumen del contenido incluido en la página 5
ASSEMBLY ASSEMBLING WHEEL CASTERS 1. Remove the hex nut and lockwasher from each of the four wheel casters. 2. Place the dust collector on its side. A 2. Insert bolt from wheel caster through the four holes (A) Fig. 3 in the base of the dust collector (three are not shown). Fig. 3 3. Place a lockwasher (A) Fig. 4 onto each bolt. 4. Thread hex nut (B) Fig. 4 onto each of the four bolts and tighten securely. B A ASSEMBLING SIDE SUPPORTS Fig. 4 1. Place the dust collector base (A) Fig. 5, in an up
Resumen del contenido incluido en la página 6
ATTACHING MOTOR AND B BLOWER ASSEMBLY TO A FRAME A 1. Place motor assembly and base assembly on their side. C 2. Align the four holes, two shown at (C), on the top of the side supports (A) Fig. 8, with the four holes in the motor assembly (B). 3. Place a 5/16" lockwasher onto a 5/16-18x3/4" hex Fig. 8 head screw and insert the bolt thru the side support and thread bolt into the tapped hole in the motor assembly. 4. Repeat this process for the three remaining holes. 5. Fig. 9 shows the motor and
Resumen del contenido incluido en la página 7
ASSEMBLING FILTER AND DUST COLLECTION A B BAGS TO DRUM 1. Thread a 5/16" hex nut (A) Fig. 13, onto the end of bag support rod (B). Thread rod into hole (E) and tighten nut (A) against motor assembly to hold support rod (B) upright. Height of support rod can be adjusted after the filter bag is in place. The hook in the support rod (B) E should be positioned over the drum. Fig. 13 B F 2. Hook the loop on the top of filter bag (F) Fig. 14, onto the end of support rod (B). 3. Position open end of f
Resumen del contenido incluido en la página 8
ASSEMBLING DUST INTAKE E C HOSE TO MOTOR AND A BLOWER ASSEMBLY The dust collector is supplied with a 4" flexible dust intake hose. Place the intake cap holder (E) on the dust collector as shown in Fig. 17. NOTE: DO NOT COVER THE INTAKE PORT WITH THE INTAKE CAP WHEN ATTACHING THE HOSE TO THE INTAKE PORT. To assemble the dust collection hose to the motor and Fig. 17 blower assembly, loosely attach hose clamp (A) Fig. 17, around one end of flexible hose (B) and assemble the hose to dust intake port
Resumen del contenido incluido en la página 9
120 VOLT, GROUNDED OUTLET BOX SINGLE PHASE OPERATION This tool must be grounded while in use to protect the CURRENT CARRYING operator from electric shock. The motor recommended PRONGS for use with your dust collector is shipped wired for 120 Volt, Single Phase, and is equipped with an approved 3-conductor cord and 3-prong grounding type plug to fit the proper grounding type receptacle, as shown in Fig. 19. The green conductor in the cord is the grounding wire. Never connect the green wire to a l
Resumen del contenido incluido en la página 10
EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the tool. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. 22 & 23, shows the correct gauge to use depending on the cord length. If in
Resumen del contenido incluido en la página 11
MAINTENANCE NOTE: Before any maintenance or service is performed, be sure the unit is disconnected from the power source to prevent accidental starting. All servicing other than the items recommended in this Instruction Manual should be performed by an authorized service facility. When storing your dust collector, remove power supply cord from the electrical outlet. Coil the cord neatly and place it off the floor on the base of the dust collector to eliminate potential cord damage. MOTOR MAINTEN
Resumen del contenido incluido en la página 12
NOTES 12
