Resumen del contenido incluido en la página 1
's I
3/4 Horsepower (continuous duty)
1-1/2 Horsepower (maximum developed)
600 C°FoM°
3450 R.PoM. (no _oad R.PoM.}
Model No.
152.213351
C
CAUTION:
Customer Helpline
FOR YOUR OWN SAFETY; Read
and follow all of the Safety and
1-800-897-7709
Operating Instructions before
PRease have your Model No.
Operating this Dust CoUlector.
and Sedal No. availabUe.
Sears, Roebuck and Co., Hoffman Estates, JL (}0179 U.S.A.
Part No. 0R92122
Revision A
Espa5olpg. 23
Resumen del contenido incluido en la página 2
SECTmON PAGE Warranty ..................................................................................... 2 Product Specifications ......................................................................... 2 Safety mnstructions ............................................................................ 3 Grounding mnstructions ......................................................................... 5 Specific Safety mnstructions for Dust Collectors ............................................
Resumen del contenido incluido en la página 3
9, GENERAL SAFETY iNSTRUCTiONS ALWAYS WEAR EYE PROTECTION, Any power tool can throw debris into the eyes during opera- Operating a Dust Collector can be dangerous if safety tions, which could cause severe and permanent and common sense are ignored, The operator must be eye damage, Everyday eyeglasses are NOT safety familiar with the operation of the tool, Read this manual glasses, ALWAYS wear Safety Goggles (that to understand this Dust Collector, DO NOT operate this comply with ANSi standard Z8
Resumen del contenido incluido en la página 4
21,EACHANDEVERY TmME,CHECK FOR DAM- The smaller the gauge number, the larger diameter of AGED PARTS PRmOR TO USmNGTHE TOOL, the extension cord. if in doubt of the proper size of an extension cord, use a shorter and thicker cord. An Carefully check all guards to see that they operate properly, are not damaged, and perform their undersized cord will cause a drop in line voltage resulting in a loss of power and overheating. USE intended functions, Check for alignment, binding or ONLY A 3-WIRE EXTEN
Resumen del contenido incluido en la página 5
The motor supplied with your Dust Collector is a 120-volt, single-phase motor, it is shipped wired for THINSTOOL MUST BE GROUNDED WHmLE mNUSE 120-volt application, Never connect the green wire to TO PROTECT THE OPERATOR FROM ELECTRmC a live terminal, SHOCK. USE ONLY A 3-WIRE EXTENSION CORD THAT HAS mNTHE EVENT OF A MALFUNCTmON OR BREAK- A 3=PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG. DOWN, grounding provides the path of bast resistance for eUectriccurrent and reduc
Resumen del contenido incluido en la página 6
12, SPECiFiC SAFETY iNSTRUCTiONS USE only as described in this manual, USE acces- sories only recommended by Sears, FOR DUST COLLECTORS 13, DO NOT pull the dust collector by the power cord, The operation of any Dust Colbctor can result in debris NEVER allow the power cord to come in contact being thrown into your eyes, which can result in severe with sharp edges, hot surfaces, oil or grease, eye damage, ALWAYS Wear Safety Goggbs (that com- ply with ANSi standard Z87,1) when operating the Dust 14
Resumen del contenido incluido en la página 7
AVAILABLE ACCESSORIES Sears may recommend other accessories not listed in this manual, Visit your Sears Hardware Department or see the Sears See your nearest Sears Hardware Department or Sears Power and Hand Tool Catalog for the following acces- Power and Hand Tool Catalog for other accessories, series, Do not use any accessory unless you have completely ITEM STOCK NUMBER read the Owner's Manual for that accessory, 21374 30 micron collection bag 4" Diameter x 10' flexible hose 21372 4" Diameter
Resumen del contenido incluido en la página 8
UNPACKING AND CHECKING CONTENTS (Figure3) if any parts are missing, do not attempt to plug in the power cord and turn "ON" the Dust Collector, The Dust This Dust Collector will require a minimal amount of Collector can only be turned "ON" after all the parts assembly, have been obtained and installed correctly, Remove all of the parts from the shipping box and lay them on a clean work surface, Compare the items to figure 3, verify that all items are accounted for before discarding the shipping b
Resumen del contenido incluido en la página 9
Fig. 4 D G E F B A, 4-inch HnHet Port B, 4-inch FHexibHe Hose C, Hntake Port Cap D, Hntake FunneH E, Support Rod R 4-inch Exhaust Port G, CoHHectionBag H, Dust CoHHector H, Base J, Caster
Resumen del contenido incluido en la página 10
Fig. 6 DO NOT assemble the Dust Collector until you are sure the tool iS NOT plugged in, 2, DO NOT assemble the Dust Collector until you are sure the power switch is in the "OFF" position, 2, For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire Owner's Manual, SWIVEL CASTER TO BASE ASSEMBLY 3, Place 3/8=16 flange hex nut (C) onto bolt (D) of swivel caster and tighten, See figure 6, MAKE CERTAIN THE DU
Resumen del contenido incluido en la página 11
Fig. 8 Fig. 10 C D \ \ C 2, insert a 5/16-18 x 5/8" hex head screw (C) through 2, insert the lower support tube (C) into the lower the exhaust flange, exhaust flange gasket and the support tube holder and tighten support tube clamp, exhaust port flange, See figure 8, See figure 10, 8, Thread 5/16-18 flange hex nut (D) onto the 5/16=18 x 5/8" hex head screw, do not tighten completely, 3, Place support tube clamp over top of lower support See figure 8, tube, 4, Repeat Steps 1,2, and 3 for the rema
Resumen del contenido incluido en la página 12
2. Hnsert two5/16-18 x 5/8"buttonheadcarriage boHts iNTAKE PORT CAP AND through theinsideoftheintakefunneiandintake HOSE ASSEMBLY support brace. 3. Piace a 5/16-18 flange hex nut onto the button MAKE CERTAIN THE DUST COLLECTOR IS head carriage boits and tighten secureiy. DISCONNECTED FROM THE POWER SOURCE. F Fig. 14 A D C E E D 4, Attach the upper support bracket (C) to the hob (D) in the intake support brace with the adjustabie Hock- ing iever (E). Piace a 5/16" Hockwasher (F) onto 1, SHde the
Resumen del contenido incluido en la página 13
Loosely thread end of collection bag strap (A) through clamp (B), Place open end of collection G bag (C) over exhaust port (D) and firmly pull strap to fasten collection bag to exhaust port, See figure 16 and 17, H j ................ jf 4, Place the 4-inch hose clamp (F) on the other end of / / 4-inch flexible hose (G), Slide 4-inch flexible hose / over the intake funnel (H) and tighten 4-inch hose clamp securely, See figure 15, COLLECTION BAG TO D DUST COLLECTOR ASSEMBLY MAKE CERTAIN THE DUST C
Resumen del contenido incluido en la página 14
LOCKING SWITCH JN THE "OFF" POSiTiON FOROPERATOR SAFETY, keepfingersandaliforeign objectsoutoftheintakeports,Therotating faninside When the Dust Collector is not in use, the switch key theMowerhousing isaccessibie through theintake (B) shouid be removed so that it cannot be started, portsandishazardous, Donotwearboseciothing or Grasp the switch key and puli it out of the switch jeweiry,Makecertain thateachintakeportwhichisnot assembiy, With the switch key removed, the switch beingusedorattached
Resumen del contenido incluido en la página 15
HELPFUL HINTS: Belowaresometermsthatwiiihelpyouto understand andsetupyourDustCollector anddesign yourown , Alwaysrunthelargestappropriate diameter hose DustCollection System, asfaraspossible, Running asmaller diameter hose wiiigreatlyreducetheC,F,M, at thetool,yielding DustCollector- A machine usedto collectfinewood marginal dustcollection, dustandchips, Theuseof a lowratedmicronfilterandcollection bagcanincrease theeffectiveness ofyourdust DustCollectionSystem- Adustcollector connected collecto
Resumen del contenido incluido en la página 16
C.F.M. REQUIREMENTS FORTOOLS Machine Minimum C.F._,_.Required Minimum Duct Diameter Band Saw (12 to 16qnch) 350 C,F,M, 4qnch BeWDbc Sander 450 C,F,M, 5qnch DrHUPress 350 - 400 C,RM, 4qnch Drum Sander (12 to 24qnch) 550 - 700 C,RM, 5qnch Fbor Sweep 350 - 400 C,RM, 4 to 5qnch Jointer (up to 8qnch) 350 - 400 C,RM, 4 to 5qnch Jointer (over 8qnch) 450 - 550 C,RM, 5qnch RadiaUArm Saw 450 - 600 C,RM, 5qnch Miter Saw 450 - 600 C,RM, 5qnch Router TaMe 200 C,F,M, 3qnch Scroll Saw 200 C,F,M, 3qnch Spindb S
Resumen del contenido incluido en la página 17
Topurchase anyoftheDustCollection Accessories listedbelow, visityournearest SearsStore, VariousFittings: 21340 3=inch HoseCoupling 21341 4-inchHoseCoupling 21363 3=inch 90=degree Elbow 21364 4-inch90-degree Elbow 21365 3=inch Y=Fitting 21366 4-inchYoFitting 21367 3=inch T=Fitting 21368 4-inchToFitting HOSe: 21370 3-inch x lO-foot Flexible Hose 21371 3-inch x 25-foot Flexible Hose 21372 4-inch x lO-foot Flexible Hose 21373 4-inch x 25-foot Flexible Hose Blast Gates 21359 3-inch Blast Gate - Plast
Resumen del contenido incluido en la página 18
Turnthepowerswitch"OFF" andunplugthepower airmaydamage insulation.Theoperator should always cordfromitspowersourcepriortoanymaintenance, weareyeprotection whenusingcompressed air. Alwaysmakesurethattheintakeportcapscovers the intakeportwhena hoseis notconnected tothedust Donotallowchipsanddusttoaccumulate underdust collector. collector.Keepareacleanandinsafeorder. CAUTION: DONOTUSEFLAMMABLE MATERIALS tocleanDustCollector. TheDustCollector hassealedlubricated bearings in themotorhousing thatdoesn
Resumen del contenido incluido en la página 19
PORTABLE DUSTCOLLECTOR PARTS UST MODELNO.152.213351 Whenservicing, useonlyCRAFTSMAN replacement parts,Useof anyotherpartsmaycreatea NAZARD orcause product damage, Anyattempt to repair or replace electrical partsonthisDustCollector maycreatea NAZARD unlessrepairisdoneby aqualified servicetechnician, Repair serviceisavailable at yournearest SearsServiceCenter, AlwaysorderbyPARTNUMBER, notbykeynumber, Key No, PART No, Description Qty. Key No. PARTNo. Description Qfry. 1 OR90613 1 29 0R90638 GASKET
Resumen del contenido incluido en la página 20
PORTABLE DUSTCOLLECTOR PARTS UST MODELNO,152,213351 55-- 52 20
