Resumen del contenido incluido en la página 1
®
GE Monogram
Installation
Instructions
with
Optional Trim Kit
Installation Instructions
Built-In
Dishwashers
Models
ZBD5600
ZBD5700
ZBD5900
Resumen del contenido incluido en la página 2
Before you begin - Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions with your Use and Care Book for future reference. This appliance must be properly grounded. See “Power Supply”, page 8. CAUTION WARNING Cet appareil doit être correctement mis à la terre. CAUTIO
Resumen del contenido incluido en la página 3
Design Information Stainless Steel Interior Dishwashers ZBD5600 WW, ZBD5700 WW Models White Dishwashers Available ZBD5600 BB, ZBD5700 BB Black Dishwashers ZBD5900 SS Stainless Steel Dishwasher These dishwashers are designed for versatility, adaptable to virtually any installation. These models have a full length trimless door without the traditional access panel. The black and white models can be customized with decorative panels of wood or other material. G C A – 34” Min. adjustable B Product t
Resumen del contenido incluido en la página 4
Design Information Stainless Steel Interior Dishwashers • Install in standard 24” deep cabinets: Cabinet Cabinet Standard Depth Resting – The dishwasher door will be flush with the 24" Against Wall installation front face of adjacent cabinetry. • With a 3/4” thick custom door panel in in 24” deep place, the exterior is trimless and fits flush cabinets to adjacent cabinetry. • ZPF25W, white or ZPF25B, black custom Optional panel kit – Provides for the installation of a Trim Kits 1/4” thick custom
Resumen del contenido incluido en la página 5
Installation Information Stainless Steel Interior Dishwashers Remove the hardware accessory bag and Parts other parts from inside or taped to the Supplied outside of the dishwasher. Check contents against drawings to insure that all parts are included. nn 2 toekick slides nn 2 toekick support brackets nn 2 side trim pieces nn 2-piece toekick nn 16 Screws (see illustration) nn 2 leveling legs 2 Leveling Legs nn Junction box Screw B (4) Side Trim Screw A Screw C (2) Countertop Screws (4) Toekick M
Resumen del contenido incluido en la página 6
Installation Preparation Stainless Steel Interior Dishwasher nn 90° elbow (3/8" NPT external thread on one end and opposite Materials You end to fit hot water supply line) Will Need: nn Thread seal tape nn UL listed wire nuts (3) Electrical Cable (not supplied) or Power Cord 90° Elbow For new installations only: nn Air gap for drain hose, if required Screw Type Clamps nn Waste tee for house plumbing, if applicable nn Electrical cable or power cord, if applicable Thread Seal nn Screw type hose cl
Resumen del contenido incluido en la página 7
Installation Preparation Stainless Steel Interior Dishwasher • The rough cabinet opening must be 24” Prepare min. deep, 23-5/8” min. to 24” max. wide. the The opening height should be 34” min. This Wall Area and 35” max. must be Free of Opening Pipes or Wires • The opening should be free of extraneous 34" to 35" 24" pipes and wires. 1-3/4" Underside Min. of Countertop to Floor 6" 23-5/8" Min. 24" Max • Hot water line may enter from either side, Water from the rear, or from the floor within the
Resumen del contenido incluido en la página 8
Installation Preparation Stainless Steel Interior Dishwashers FOR PERSONAL SAFETY: Power WARNING REMOVE HOUSE FUSE OR OPEN Alternate Supply CIRCUIT BREAKER BEFORE BEGINNING Receptacle INSTALLATION. Location DO NOT USE AN EXTENSION CORD OR 18" ADAPTER PLUG WITH THIS APPLIANCE. 1-1/2" Dia. Hole (Max.) FOLLOW NATIONAL ELECTRICAL Receptacle Location CODES OR PREVAILING LOCAL CODES 18" Area AND ORDINANCES. 3" 6" 6" from 2" AVERTISSEMENT Cabinet 2" 24" SÉCURITÉ from Wall IL FAUT ENLEVER LE FUSIBLE DE
Resumen del contenido incluido en la página 9
Installation Preparation Stainless Steel Interior Dishwasher • Follow local codes and ordinances. Method 1 – Air Gap with Waste Tee or Disposer Prepare • Dishwasher drain hose must not exceed 10 Use this method when waste tee or disposer connection is less drain feet in length for proper drainage. than 12” above the floor. – The dishwasher is supplied with a 3/4” plumbing I.D. drain hose, 78” long. Add up to 42” length to the factory supplied hose if necessary. • Dishwasher must be connected to
Resumen del contenido incluido en la página 10
Installation Stainless Steel Interior Dishwasher • If you intend to install custom door panels, Install Custom refer to installation instructions provided in Door Panel this booklet. The panels should be in place before installing the dishwasher. Cut the shipping carton and use it as a pad Step 1 under the dishwasher. This will protect the Remove finished floor in the kitchen. • Lay the dishwasher on its back. wood base • Remove the 4 screws holding the dish- washer to the wood base. Discard scr
Resumen del contenido incluido en la página 11
Installation Stainless Steel Interior Dishwasher • Install the 90° elbow onto the water inlet. Step 3 Use thread sealing tape or pipe thread Install compound. • The 90° elbow should face the left or right Water Inlet side, depending on water line routing. Fittings • Install strain relief onto junction box and Step 4 tighten against incoming wires. Install • Strip 1/2” insulation from end of power cord wires. power cord • Connect incoming wires to dishwasher wires (If used) using wire nuts of app
Resumen del contenido incluido en la página 12
Installation Stainless Steel Interior Dishwasher • Carefully upright the dishwasher, taking Step 5 care not to bend the leveling legs. Make Level the sure the leveling leg locking nuts are secure. Dishwasher • Check to be sure the dishwasher is level and at the cutout height. • Insert drain hose into the hole previously Step 6 drilled in the cabinet wall. Slide • Slide the dishwasher into the opening a few Dishwasher inches at a time. • As you proceed, pull the drain hose Into Opening through th
Resumen del contenido incluido en la página 13
Installation Stainless Steel Interior Dishwasher • Follow all local codes and ordinances. Method 1 – Air Gap with Waste Tee or Disposer Step 8 Drain Line Preparation Install • The dishwasher is supplied with a 78” long corrugated drain hose. Drain Line • If the location requires a longer drain hose, add up to 42” length to the supplied hose. Use 3/4” inside diameter hose and thin wall copper coupler to join the hose ends. Waste Tee Installation Disposer Installation Note: Total drain hose length
Resumen del contenido incluido en la página 14
Installation Stainless Steel Interior Dishwasher To maintain position and alignment the Step 10 dishwasher must be secured to the countertop Secure or to adjacent cabinetry. If countertop is of stone or other hard Dishwasher material, secure the dishwasher to adjacent to Countertop cabinets. • Check to be sure that dishwasher is adjusted or Cabinetry to correct height and is centered in the cutout. • Open and close dishwasher door to insure proper operation of the door. If there is any binding o
Resumen del contenido incluido en la página 15
Installation Stainless Steel Interior Dishwasher • Install toekick slides to toekick support Front Toekick Panel Step 11 brackets. Use slide stamped “L” on left and Install “R” on right side. • Align front and inner toekicks, matching Toekick screw holes. Assembly • Align toekick to second screw hole in toekick slide as illustrated. • Install color matched screws “E” through the front of the toekick and into the toekick slides. Do not tighten screws. Left Side • Carefully, slide assembly back un
Resumen del contenido incluido en la página 16
ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel Note: It is best that 2 people perform this installation. ZPF25B, Black trim ZPF25W, White trim The ZPF25 trim kit provides support for 1/4” thick custom door panel. Tools and Materials required • Phillips screwdriver Note: Maximum custom panel weight is • Gloves to protect against sharp edges. 10 pounds. To prevent electrical shock, WARNING AVERTISSEMENT disconnect electrical power Pour éviter les supply to dishwasher before électrocution
Resumen del contenido incluido en la página 17
ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Open the door fully. Step 2 Remove Caution: One person should hold the door while the other backs out screws to prevent Existing the metal door from falling. Metal Door • Remove 6 screws on the inside the inner door frame. Retain screws. • Remove the 2 screws with o-rings located in the bottom center of the inner door. Retain screws and o-rings. • Remove the outer door. • Remove the 2 screws holding the center door bracket to metal door.
Resumen del contenido incluido en la página 18
ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Locate the “C” clips in the parts package. Step 5 Place one clip, flat side up, over each of the Install screw holes, 3 on each side of the door. Assembled Note: One person should hold the door while the other installs Door onto screws to prevent the door assembly from falling. Dishwasher • Hold the assembled door to dishwasher inner door and slide up against control panel. Control panel has posts that should engage the 2 holes in the to
Resumen del contenido incluido en la página 19
ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel ZPF75B, Black Note: It is best that 2 people perform this installation. ZPF75W, White The ZPF75 provides for the installation of 1/2” to 3/4” thick custom door panel. Tools and Materials required • Phillips screwdriver Note: Maximum custom panel weight is • Gloves to protect against sharp edges 10 pounds. • Nut driver AVERTISSEMENT To prevent electrical shock, WARNING Pour éviter les disconnect electrical power électrocutions, il faut supply to
Resumen del contenido incluido en la página 20
ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel • Open the door fully. Step 2 Remove Caution: One person should hold the door while the other 2 “O” Rings backs out screws to prevent the metal door from falling. Existing Metal Door • Remove 6 screws on the inside of the frame. Retain screws. • Remove the 2 screws with o-rings located in the bottom center of the door. Retain screws and o-rings. • Remove the door. • Remove insulation and foam inserts, 2 Foam discard metal door. Inserts • Insta
