Resumen del contenido incluido en la página 5
23 7/8” (60.6 cm) 24” (61 cm)** 33 7/8” (86 cm) min. with wheels removed 6 3/4” 10 1/2” (17.2 cm) (26.7 cm) 1 3/4” Clear 6 1/4” (4.4 cm) Area (15.9 cm) 2 1/2” (6.4 cm) Product and Cabinet Opening Dimensions *Insulation may be compressed (not used on all models) Check that all surfaces have no protrusions that would prohibit dishwasher installation. NOTE: Shaded areas of cabinet walls show where utility connections may be installed. *Measured from the lowest point on the underside of countert
Resumen del contenido incluido en la página 6
Drain Requirements Electrical Requirements • A new drain hose is supplied with your dishwasher. Be sure that the electrical connection and wire size are If drain hose is not long enough, use a new drain hose adequate and in conformance with the National Electrical with a maximum length of 12’ (3.7 m) (Part Number Code, ANSI/NFPA 70 - latest edition and all local codes and 3385556) that meets all current AHAM/IAPMO test ordinances. standards, is resistant to heat and detergent, and fits the A cop
Resumen del contenido incluido en la página 7
6“ (15.2 cm) INSTALLATION INSTRUCTIONS Prepare Cabinet Opening—Existing Utilities WARNING Check water and electrical 1 placement Water line Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. Cable Disconnect power 1 If the water line and the cable extend to the locations Disconnect electrical power at the fuse box or circuit shown, proceed to the “Install Drain Hose” s
Resumen del contenido incluido en la página 8
6” (15.2 cm) Power Supply Cord–Prepare hole Direct Wire–Route cable 2 3 Metal Wood cabinet cabinet Route cable from power supply through cabinet hole (cable Wood cabinet: Sand the hole until smooth. must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit Metal cabinet: Cover hole with grommet included with cable from moving when dishwasher is moved into power supply cord kit. cabinet opening. Option B, Direct Wire: Prepare and Route W
Resumen del contenido incluido en la página 9
Route water supply line Route drain hose 3 2 Drain hose Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape drain hose to the floor in area shown. This will Slowly route water supply line through hole in cabinet. prohibit it from moving when dishwasher is moved into (If using copper tubing, it will bend and kink easily, so be cabinet opening. gentle.) It should be far enough into the cabinet opening to connect it to the dish
Resumen del contenido incluido en la página 10
Option B, No waste disposer – no air gap Option D, No waste disposer – with air gap No waste disposer – no air gap No waste disposer – with air gap Large silver Screw-type Air gap Air gap drain hose clamp clamp Screw-type clamps S Screw-type clamps crew-type clamps Large silver drain Large silver drain hose clamp hose clamp W W Waste tee a aste tee ste tee (provided) Drain hose W Waste tee aste tee Rubber hose connector Drain trap Drain trap Drain hose Drain trap Drain t
Resumen del contenido incluido en la página 11
® Apply T eflon tape Prepare Dishwasher 3 or pipe joint compound Coarse threads Coarse threads WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. ® Apply Teflon tape or pipe joint compound to 90˚ elbow fitting (not provided). Wrap tape around coarse threads two to four times to prohibit leaks. WARNING Excessive Weight Hazard Connect 90° elbow fitting to 4 Use two or more people to move and ins
Resumen del contenido incluido en la página 12
WARNING 6 Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Install a UL Listed/CSA Certified strain relief. Make sure Failure to follow these instructions can result in screwheads are facing to the left when tightening conduit death, fire, or electrical shock. nut. Strain relief is provided with the power supply cord kit. What type of electrical Power Supply Cord— connection will you use? 2 Conne
Resumen del contenido incluido en la página 13
Determine Cabinet Opening Wiring configuration Power supply wire: Terminal box wire: Measure cabinet opening 1 white white black black ground wire ground connector If needed, see website for animated representation of this step. Visit www.jenn-air.com under FAQ tab. Power Cord - Secure cord 4 on strain relief Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and
Resumen del contenido incluido en la página 14
2” (5 cm) IMPORTANT: Do not scratch the front panel during this procedure. Built-up Floors—Add 3 shims as needed Remove the door handle and hardware bag containing the setscrews and Allen wrench from the cardboard box. Setscrews are already installed in the handle. Place handle on mounting studs with the setscrews facing down. Push the door handle tightly against the door. Insert the short end of the Allen wrench into the setscrews. Tighten the setscrews 1/4 turn past snug. Retain Allen wrench
Resumen del contenido incluido en la página 15
Dishwashers with control panel on Attach handle 5 2 top custom panel dimensions 6” (15.2 mm) 3 screws Hex Head per side Screw outer panel Attach outer panel to back of customer-supplied custom panel with the four #10-16 x 3/8" hex head screws supplied Gently set outer panel aside. Lay the customer-supplied in the literature package. Attach the handle. The handle custom panel face down on a covered, non-scratching should be centered on the front of the customer-supplied surface. custom panel in t
Resumen del contenido incluido en la página 16
Option 2, Dishwasher side attachment: Install custom panel 8 Remove brackets from the top 1 Align top edges Drill through these holes tabs Customer-supplied panel To remove the brackets from the top, flatten tab at back 1 3/8” Screw of brackets with pliers, and pull the brackets out of the Install the two #8-18 x 1 3/8" screws from slots. the literature package in the top corners of the inner panel. Tighten the six side screws reinstalled in Step 6. Break end of bracket 2 Choose Attachment Opti
Resumen del contenido incluido en la página 17
Move dishwasher close to Reinstall bracket 4 2 cabinet opening bend Drain tabs hose Direct wire only Water Push bracket into slot on the side of dishwasher, and line bend tab in toward the side of the dishwasher so that it Cable keeps the bracket in place. Repeat this step for the other side of the dishwasher. NOTE: Do not attach the dishwasher. This will be done IMPORTANT: Double-check correct placement of utilities. later. Grasp the sides of the dishwasher at the edges of the door panel. Tilt
Resumen del contenido incluido en la página 18
Closes too quickly — Move dishwasher into 5 7 Decrease spring tension cabinet opening spring Insulation blanket tensioner screw IMPORTANT: If wheels were removed, avoid damage to the floor when moving the dishwasher. Slowly move To adjust the door spring tension, unhook the spring dishwasher completely into cabinet opening. Do not kink from the rear leg of dishwasher. or pinch water line, drain hose, power supply cord or Using a 5/16" nut driver or hex socket, remove the screw direct wire betwe
Resumen del contenido incluido en la página 19
Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. With Connect water supply 2 some installations, it may be easier to adjust the front leg using copper or flexible line using the 3/16” hex head socket or adjustable wrench. Preferred method Optional method Copper tubing only: Put the tubing into the 90° elbow fitting as far as it will go (the copper tubing bends and kinks easily). Slide the nut and ferrule forward and start the nut onto the elbo
Resumen del contenido incluido en la página 20
Connect to Drain Make Direct Wire Electrical Connection Connect drain hose 1 NOTE: If the power supply cord was connected earlier, proceed to “Secure Dishwasher in Cabinet Opening” Green clamp section. Option B, Direct Wire: Black drain hose Drain hose connector Direct Wire-—Route cable Drain hose stop 1 into terminal box Stop Stop Place towel under drain hose to catch any water in drain hose. Place the small green drain hose clamp onto the small end of the drain hose. Push the new drain hose i
Resumen del contenido incluido en la página 1
INSTALLATION INSTRUCTIONS
UNDERCOUNTER DISHWASHER
INSTRUCTIONS D'INSTALLATION
LAVE-VAISSELLE SOUS PLAN DE TRAVAIL
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
W10208727A
Resumen del contenido incluido en la página 2
Table of Contents Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Instructions (cont.) Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Determine Cabinet Opening . . . . . . . . . . . . . . . . . . . . . . . 13 Tools and Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Install the Door Handle (on some models) . . . . . . . . . . . 14 Location Requirements . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
INSTALLATION REQUIREMENTS Other parts you may also need: Tools and Parts Gather the recommended tools and parts before starting Masking or 1 1/2" –2" installation. Read and follow the instructions provided with duct tape (3.81–5.0 cm) any tools listed here. Screw-type clamps (3 max) All Installations Tools needed: NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See Flat-blade “Electrical Requirements” section. It is recommended
Resumen del contenido incluido en la página 4
Location Requirements Grounded electrical supply required. Check location where dishwasher will be installed. The location must provide: Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. • easy access to water, electricity and drain. The location where the dishwasher will be installed must • convenient access for loading and unloading dishes. provide clearance between motor and flooring. Motor Corner locations require a 2”
