Resumen del contenido incluido en la página 1
©2008 Pella Corporation Part Number: 801V0101
INSTALLATION INSTRUCTION – INSTRUCCIONES DE INSTALACIÓN
FOR CLAD HINGED PATIO DOOR
PUERTA DE BISAGRA PARA PATIO
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
Door Top
Fin
Corner
Corner
Flashing
Tape
Nailing Fin
Top
Flashing
Tape
Corner
Water
Flashing
Resistive
Side
Tape
Barrier
Flashing
Tape
Sheathing
Framing
Optional
Nailing Fin
Side
Flashing
Sill Flashing Tape #1
Tape
Sill Support
Sill Flashing Tape #2
Do
Resumen del contenido incluido en la página 2
Interior Interior Exterior SEALANT SEALANT YOU WILL NEED TO SUPPLY: TOOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • Tape measure • 2" galvanized roofing nails (1/4 lb.) • Level • Closed cell foam backer rod/sealant backer (12 to 30 ft.) ® ™ • Pella SmartFlash foil backed butyl window and door • Square flashing tape or equivalent • Hammer • High quality exterior grade polyurethane or silicone sealant • Stapler (1 tube per window) • Great Stuff ™ Window and Door Insulating F
Resumen del contenido incluido en la página 3
1" 6" Exterior E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown 1E (1E) so it overhangs 1" to the exterior. Note: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening. 1F F. Tab the sill flashing tape and fold. Cut 1" wide tabs at each corner (1/2" from each side of corner) (1F). Fold tape to the exterior and press firmly to adhere it to the water resistiv
Resumen del contenido incluido en la página 4
1 INCHES 2 3 mm 20 30 40 50 60 70 Exterior Interior Exterior Interior E. Plumb and square door. Place shims at each hinge and lock 2E strike location between the door and the sides of the opening. Insert shims in other locations as needed starting up 6" from the bottom of the door to square it in the opening. Make sure that the reveal around the door(s) is equal. On double doors, make sure that panels are even across the bottom. Note: DO NOT over shim. F. Check the interior reveal. Make
Resumen del contenido incluido en la página 5
1" Exterior Exterior Exterior INTEGRATING THE DOOR TO THE 3 WATER RESISTIVE BARRIER Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape. A. Apply side flashing tape. Cut two pieces o
Resumen del contenido incluido en la página 6
Interior 4 INTERIOR SEAL Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation. A. Apply insulating foam sealant. From the interior, insert 4A the nozzle of the applicator approximately 1" deep into the space between the door and the rough opening and apply a 1" deep bea
Resumen del contenido incluido en la página 7
A. Install the hardware. Refer to the instructions included in the hardware box. B. Insert backer rod into the space around the door 3/8" to 1/2". This should provide at least a 3/8" clearance between the backer rod and the exterior face of the door. Note: Backer rod adds shape and depth for the sealant line. 5B C. Apply a bead of high quality exterior grade sealant to the entire perimeter of the door. At each end of the bottom of the door, insert sealant into the spaces between the botto
Resumen del contenido incluido en la página 8
EXTERIOR FINISH The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad® or EnduraClad Plus baked-on factory finish that needs no painting. Clean this surface with mild soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface. Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door materials
