Resumen del contenido incluido en la página 1
Owner’s Manual
Synchrony Series
Guide d’utilisation
Manual de Propietario
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Owner’s Manual Congratulations on purchasing your new PSB Synchrony loudspeaker. We hope that you enjoy our product for many years to come. This owner's manual will give you many useful tips about connecting, placing and using your loudspeaker. We recommend you read it thoroughly and it should answer all of your product related questions. If not, feel free to contact us through our website: www.psbspeakers.com Synchrony design background A little technical background might give you an a
Resumen del contenido incluido en la página 4
These two factors causing distortion in bass drivers are practically eliminated by the combination of an aluminum shorting ring within the magnet structure, the aluminum phase plug on the pole piece, and a shorted copper turn on top of the pole piece. The aluminum phase plug smoothes response and also contributes as a heat sink for the voice coil, reducing power compression. Long voice coils for all woofers (in a narrow gap) ensure high and uniform BL vs. excursion, to maintain dynamic l
Resumen del contenido incluido en la página 5
Owner’s Manual Additional features of the Synchrony models: ? 1" Titanium Tweeter/Neodymium Motor/Aluminum Heat Sink. Low mass for required stiffness needed for wide bandwidth response. High efficiency and high power handling. ? Three chamber individually ported cabinet design (tower models) gives greater control over the system tuning, resulting in deeper bass. Doesn't suffer from the standing wave problems found in a typical tower. ? Perforated Hex Acoustically transparent Metal Grill c
Resumen del contenido incluido en la página 6
Adjusting Rubber Levelers and Spikes (Tower Speakers) Attach the supplied spikes or rubber levelers to the bottom of the speaker as shown in the diagram at right. On carpets, position the speakers and adjust spikes to the desired height (higher for thicker carpet) and hand tighten the locknuts against the bottom of the cabinet. Adjusting Rubber Foot (For Center Channel Models) The Synchrony One C and Two C center channel speakers come supplied with a multi-position foot that allows
Resumen del contenido incluido en la página 7
Owner’s Manual Wall Mounting Synchrony S Surrounds Select and install wall-mounting brackets and hardware sufficient to hold the weight of the speakers on the walls safely. 1. Use the “3 finger” style flush mount bracket (provided in Owner's Manual Kit). 2. The speaker should be mounted at a minimum height of five feet measured from the bottom of the speaker to the ground. The speaker can be mounted on the wall beside or behind the listener. Screws with sufficient length and located to so
Resumen del contenido incluido en la página 8
Speaker Placement — Maximizing Your Enjoyment Proper loudspeaker placement is an essential ingredient to getting the best sound from your high performance stereo, multi-channel audio or home theater system. The goal is to reproduce faithfully the audio soundtrack the movie director or music producer created without calling any attention to the speakers themselves. All distances are equal All distances are equal 5.1 surround speaker placement 6.1/7.1 surround speaker placement Fortunately, i
Resumen del contenido incluido en la página 9
Owner’s Manual enclosures are positioned vertically rather than horizontally. If you are placing your monitors horizontally, the speakers will still perform very well, but the seating area where you will enjoy optimum sound will become narrower. We suggest you position the tweeters to the outside away from the center line. You may prefer to tilt the speakers towards ear level. D. If you sit equally distant from both speakers, angling the speakers inward (“toeing them in’) about 5 to 10 de
Resumen del contenido incluido en la página 10
inches from all walls, but the choice is yours to determine by listening. 2. You in Relation to the Speakers Where you sit in relation to your speakers obviously makes a difference too. The proportions of the particular triangle formed by your speakers and you matter. (You may need to send more power to the more distant speaker to compensate if you get much further from one speaker than the other.) The overall distances involved also matter. As you get further from the speakers, more s
Resumen del contenido incluido en la página 11
Owner’s Manual 4. Positioning Surround Speakers We are often asked about what kind of surround speakers are best: dipole, bipole, or monopole (direct-radiator). Placement, room acoustics, and other factors affect the sonic realism of movies and Null Zone Bipole 5.1 System Dipole 5.1 System multi-channel audio at least as much as the radiating characteristics of a speaker. Therefore, we do not make specific recommendations but rather suggest you discuss the best solution for your particular
Resumen del contenido incluido en la página 12
positioning relation to the listener to obtain the level of direct versus diffuse sound that you prefer. Most people find it best to mount dedicated surround speakers like our Synchrony S Surrounds on the side walls slightly behind the prime listening position and two feet above ear height when seated (this typically places the bottom of the speaker about 5 feet (1.5 m) above the floor.) The surround speakers can also be mounted at ceiling level or on floor stands if this is preferred
Resumen del contenido incluido en la página 13
Owner’s Manual Connections Important: Always turn off your electronic equipment before connecting speakers. Selecting Speaker Wire We recommend the 2 following gauge of Under 25 ft (7.5 m): 16-gauge – (1.3 mm ) 2 standard two-conductor 25-50 ft (15 m): 14-gauge – (2.1 mm ) 2 speaker wire for the Over 50 ft (30 m): 12-gauge – (3.3 mm ) wiring distances specified; if you prefer, you can use heavier (lower-gauge) wire. You may wish to audition and compare the performance of some of the spec
Resumen del contenido incluido en la página 14
Bare Wire Connection Banana Plug Connection Spade Plug Connection Loosen 1/2" (13mm) Insert banana plug into Loosen wingnut to expose wingnut. Insert wire the top of the wingnut. the top of the jumper strap. through hole and tighten Ensure the wingnuts are A 1/4"(6mm) or 5/16"(8mm) nut. Takes wire sizes up tightened. spade will fit on the to 8 gauge. narrower section of the post. Tighten the wingnut. marked with ‘+’ plus signs, or one wire under the insulation may be different from th
Resumen del contenido incluido en la página 15
Owner’s Manual Bi-Wire Connections First remove jumper Right Left Amplifier + - Pre-amp Bi-Amp Connections First First remove remove Front jumper jumper Left Amplifier Right Amplifier Right Left Right Left + + - - Pre-amp Speaker Connection Options (For Synchrony S Surrounds) The captioned illustrations below show the following multi-channeled configurations: 1. Bipole or direct radiating surround mode 2. Dipole surround mode 3. 6.1/7.1 system utilizing two (2) Synchrony S surrounds 4. 6.
Resumen del contenido incluido en la página 16
Bipole or direct radiating surround mode Black Red Black Red From amp From amp From amp From amp left SURROUND left SURROUND right SURROUND right SURROUND channel channel channel channel Front Dipole surround mode Black Red From amp From amp Null Zone right SURROUND right SURROUND channel channel Front First First First First remove remove remove remove jumpers jumpers jumpers jumpers Wire Jumpers Black Red From amp From amp left SURROUND left SURROUND channel channel Replace gold-plated jumpers
Resumen del contenido incluido en la página 17
Owner’s Manual 6.1/7.1 System Utilizing Two (2) Synchrony S Surrounds — Surround — Rear Black Red Black Red From amp From amp From amp From amp left REAR left REAR right SURROUND right SURROUND channel channel channel channel Front First First First First remove remove remove remove jumpers jumpers jumpers jumpers Black Red Black Red From amp From amp From amp From amp left SURROUND left SURROUND right REAR right REAR channel channel channel channel 17
Resumen del contenido incluido en la página 18
6.1/7.1 System Utilizing Three (3) Synchrony S Surrounds — Surround — Rear Black Red Black Red From amp From amp From amp From amp left SURROUND left SURROUND right SURROUND right SURROUND channel channel channel channel Front Black Red From amp From amp right SURROUND right SURROUND channel channel First First remove remove jumpers jumpers Black Red From amp From amp right REAR right REAR channel channel 18 Owner’s Manual
Resumen del contenido incluido en la página 19
Owner’s Manual 6.1/7.1 System Utilizing Four (4) Synchrony S Surrounds — Surround — Rear Black Red Black Red From amp From amp From amp From amp left SURROUND left SURROUND right SURROUND right SURROUND channel channel channel channel Front Black Red Black Red From amp From amp From amp From amp left REAR left REAR right REAR right REAR channel channel channel channel 19
Resumen del contenido incluido en la página 20
Synchrony Port Cover A Port Cover accessory is supplied with each tower (Synchrony One and Two) and center channel speaker (Synchrony One C and Two C). The port covers can be used to adjust the bass tuning of the Synchrony models where room problems at low frequencies (in the 100Hz region) occur. It is well known that the room can dominate the performance of the low frequencies below 200Hz and the added flexibility of a port cover can tweak/improve the performance in problem room
