Resumen del contenido incluido en la página 1
8588107000
(485793)
Model
LM16
LIVE MIXER
Ownerʼs manual
: The LM16 will be upgraded to a new version for feature en-
hancement or improvement. Check the information about the latest
software version from the Fostex website (http://www.fostexinterna-
tional.com/), Fostex service station or your local Fostex dealer.
You can upgrade the software yourself. See page 36 for details about
how to upgrade the software.
Resumen del contenido incluido en la página 2
Model LM16 CAUTION: CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE RISK OF ELECTRIC SHOCK BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. DO NOT OPEN ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA DO NOT REMOVE COVER (OR BACK). PRISE ET POUSSER JUSQU' AU FOND. NO USER - SERVICEABLE PARTS INSIDE. The lightning flash with arrowhead symbol, within an equilateral REFER SERVICING TO
Resumen del contenido incluido en la página 3
Model LM16 Important Safety Instructions 1) Read these instructions. 11) Only use attachments/accessories specified by the manufacturer. 2) Keep these instructions. 12) Use only with the cart, stand, tripod, 3) Heed all warnings. bracket, or table specified by the manufacturer, or sold with the apparatus. 4) Follow all instructions. When a cart is used, use caution when 5) Do not use this apparatus near water. moving the cart/apparatus combination to avoid injury from tip-over. 6) Clean only wit
Resumen del contenido incluido en la página 4
Model LM16 Table of contents Safety instructions ..........................................................................................................2 Introduction .........................................................................................................7 About power supply ........................................................................................................7 Precautions on installation ......................................................................
Resumen del contenido incluido en la página 5
Model LM16 Connection to external devices ......................................................................16 Connection example (live stage) .............................................................................16 Connection example (home recording) .....................................................................17 Balanced and unbalanced inputs/outputs ................................................................18 Names and functions .......................................
Resumen del contenido incluido en la página 6
Model LM16 Using the internal effects processor ...........................................................................31 Applying the internal effects ........................................................................................31 About the effect types ..................................................................................................32 Monitoring ......................................................................................................................
Resumen del contenido incluido en la página 7
Model LM16 [Introduction/Overview] Introduction Thank you very much for purchasing the Model LM16. The LM16 is a live mixer which consists of the control unit which is equipped with a digital mixer and the main unit which is equipped with the I/O connectors. To ensure the best performance, read this manual thoroughly before using the LM16. Keep this manual handy for future reference. • To prevent damage to the LM16, be sure About power supply to power on the connected devices first, then turn on
Resumen del contenido incluido en la página 8
Model LM16 [Introduction/Overview] Condensation • When temperature and humidity change suddenly (for example, when you move the LM16 from a cold place to a warm place), moisture condensation may occur to the display and panel. In such a case, leave it with the power turned off for some time until the moisture evaporates. Cleaning the exterior • For normal cleaning, use a soft dry cloth. For stubborn dirt, moisten a cloth in diluted detergent, wring it out firmly, and wipe the dirt off. Then poli
Resumen del contenido incluido en la página 9
Model LM16 [Introduction/Overview] Overview The Model LM16 consists of the control unit which is equipped with a digital mixer with intuitive analog like operation and the main unit which is equipped with the I/O connectors. You can install the LM16 flexibly by integrating these units, mounting them on a rack or setting them away from each other (up to 50 meter distance using a CAT-5 cable). The LM16 is an ideal tool for schools, houses of worship, clubs, coffee houses, project stu- dios, mobile
Resumen del contenido incluido en la página 10
Model LM16 [Introduction/Overview] Main features • Digitally controlled trim on each input channel, allowing optimum input level adjustment for each mic/line input. • Fostex originally-developed digital effect unit (reverb/delay) is built in, allowing selection from 12 effect types. • Provides 16 input faders, four group faders and stereo master fader, allowing analog like operation. • 3-band (High/Mid/Low) input equalizer on each input channel. • Insertion point on input channel 1 through 8, al
Resumen del contenido incluido en la página 11
Model LM16 [Before using the unit] Before using the unit Read this chapter carefully before using the unit. Unpacking the carton Unpack the carton and inspect the contents for damage or shortages. The following contents should be found in the carton. If you find any damage or shortages, contact your Fostex dealer. Main unit (I/O connector section) x 1 Control unit (Mixer section) x 1 Power cord x 1 CAT-5 STP cable (approx. 50 cm) x 1 Operation manual x 1 11
Resumen del contenido incluido en la página 12
Model LM16 [Before using the unit] Usage examples of LM16 The control unit and main unit of the LM16 are separated. You can set these units flexibly. Integrating the main unit and control unit. You can integrate the main unit and con- trol unit. Use the supplied CAT-5 cable (approx. 50 cm length) to connect between the units. See the next page for details about how to integrate the units. Mounting the main unit and control unit on the rack. As shown on the rig
Resumen del contenido incluido en la página 13
Model LM16 [Before using the unit] Integrating the control unit and main unit Follow the procedure below to integrate the control unit and main unit. : Work on a flat and stable surface. It is recommended to put the units on a soft cloth (or blanket) to protect the units. • Phillips-head screwdriver (which matches the fixing screws for rack mounting) • The supplied CAT-5 cable (1) Remove the rack mount adaptors attached to the side panels of each unit. The removed rack mo
Resumen del contenido incluido en la página 14
Model LM16 [Before using the unit] (3) Using the rack mount adaptors removed from the control unit, fix the control unit and main unit. Attach the rack mount adaptors to the both left and right sides in the direction shown below. Use four screws for each side. Rack mount adaptor After attaching the adaptor (4) Put the CAT-5 cable into the space between the rubber feet and mounting bracket (indicated by arrows below). The space between the rubber feet and mounting bracket is narrow, so be careful
Resumen del contenido incluido en la página 15
Model LM16 [Before using the unit] Preparation of power supply Connecting the power cord INPUT Using the supplied power cord, con- nect the [AC IN] connector on the AUX SEND (-2dBu) INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT rear panel of the main unit and the MIDI OUT CONTROLLER AC outlet. PHANTOM POWER : Use only the supplied power cord. AC outlet Turning on the power INPUT Press down the [POWER] switch on the rear panel of the main unit to EFF SEND (-2dBu) AUX SEND (-2dBu)
Resumen del contenido incluido en la página 16
Model LM16 [Connection to external devices] Connection to external devices Connection example (live stage) : Before making connection between the LM16 and external devices, make sure that all devices including the LM16 are turned off, as well as all faders and level controls are down. Synthesizer Drums Guitar Bass Guitar Vocals INPUT GROUP (+4dBu) EFF SEND (-2dBu) AUX SEND (-2dBu) INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT R STEREO OUT (+4dBu) L ST MIX OUT (-10dBV) USB MID
Resumen del contenido incluido en la página 17
Model LM16 [Connection to external devices] Connection example (home recording) : Before making connection between the LM16 and external devices, make sure that all devices including the LM16 are turned off, as well as all faders and level controls are down. Synthesizer Personal computer Microphones Guitar Guitar Bass MTR Drum machine INPUT GROUP (+4dBu) EFF SEND (-2dBu) AUX SEND (-2dBu) INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT R STEREO OUT (+4dBu) L ST MIX OUT (-10dBV)
Resumen del contenido incluido en la página 18
Model LM16 [Connection to external devices] Balanced and unbalanced inputs/outputs For connection between a recording mixer such as the LM16 and external devices (such as a microphone, keyboard, recorder, etc), shielded cables are used. There are two types of cables - balanced and unbalanced. Cold Connector types Hot 2 1 Shield (ground) 3 XLR-3-11 connector (balanced) Outer 1 2 jacket 3 Balanced Unbalanced 1 Ground XLR-3-12 connector 2 Hot (balanced) Balanced 3 Cold The advantage of a balanced
Resumen del contenido incluido en la página 19
Model LM16 [Names and functions] Names and functions INPUT GROUP (+4dBu) EFF SEND (-2dBu) AUX SEND (-2dBu) INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT R STEREO OUT (+4dBu) L ST MIX OUT (-10dBV) USB MIDI OUT CONTROLLER PHANTOM POWER Main unit (Rear panel) Control unit (Rear panel) Control unit (Top panel) 19
Resumen del contenido incluido en la página 20
Model LM16 [Names and functions] Control unit (input channel 1 through 16) (1) [TRIM] control Adjusts the gain of each input signal. Set this control appropriately so that the [PEAK] indicator lights at the maximum input level. By adjusting this control appropriately, the LM16 can accept a signal within -60dBu and -12dBu for mic input, while it can accept a signal within -40dBu and +8dBu for line input (see page 28 for 1 details). 2 : When you set the [SOURCE] switch on each of chan- 3 nel
