Resumen del contenido incluido en la página 1
Trail Camera
Instruction Manual
Model #: 119256CW 03-13
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Page Index Introduction 5 Parts & Controls Guide 6-7 Battery and SD Card Installation 8 About the Setup Menu 9 Using the Setup Menu 9 SETUP MENU REFERENCE TABLE 10-11 Camera Operation 12 Mount the Camera 12 Power on the Camera 12 Test the Coverage Area 13 Secure the Camera 13 Viewing the Photos and Videos 14 Glossary 15 Technical Specifications 16 Troubleshooting/FAQ 17-20 3
Resumen del contenido incluido en la página 4
IMPORTANT NOTE Congratulations on your purchase of one of the best trail cameras on the market! Tasco is very proud of these cameras and we are sure you will be pleased with yours as well. We appreciate your business and want to earn your trust. Please refer to the notes below and the instructions in this manual to ensure that you are completely satisfied with this product. If your Tasco Trail Cam does not seem to be functioning properly or if you are having photo/video quality issues, p
Resumen del contenido incluido en la página 5
INTRODUCTION Congratulations on your purchase of a Tasco Digital Trail Camera. This camera is designed to record animal activity in the outdoors with its still image and movie modes and weatherproof, rugged construction. Your trail cam features a compact, portable size and an extra long battery life. Main Features: • 1.3 MP digital sensor • Compact Size (120mm*94mm*46mm) • Long Battery Life (Up to 6 months) • Trigger Time=1.3 seconds or less • Automatic IR Filter • LCD Display • 15 Ni
Resumen del contenido incluido en la página 6
Parts and Controls Guide PIR Motion Sensor Camera Padlock Lens Hole Infrared LED Array Tripod Socket Front of Camera PIR Indicator Light (Setup Sensor Mode Only IR LED Array Detail 6
Resumen del contenido incluido en la página 7
Parts and Controls Guide USB Port LCD Display Power Switch SD Card Slot Battery Compartment Control Panel (Front Unlatched & Opened) Control Panel Detail 7
Resumen del contenido incluido en la página 8
BATTERY and SD CARD INSTALLATION Your Tasco Digital Trail Camera is designed to operate using 4 AA batteries. We recommend using Lithium (for longest life) or Alkaline batteries. NOTE: Always set the power switch to the OFF position when installing or removing batteries. Please make sure the batteries are inserted correctly, as indicated inside the battery compartment. Incorrect voltage or polarity (+/-) will damage the camera. Do not mix old and new batteries. Do not mix battery types-use
Resumen del contenido incluido en la página 9
ABOUT THE SETUP MENU Slide the power switch to the On position. You’ll see “WAIT” on the display, then the setup menu screen. Before you start using the camera, you’ll no doubt want to set the date/time so they are imprinted correctly on your photos, and maybe change the trigger delay time and image resolution to your preferences. This is done by editing the settings of an item listed in the Setup Menu. To enter the Setup Menu at any time, press the SETUP button (to left of the power swit
Resumen del contenido incluido en la página 10
The following table lists all of the menu items, their available settings, and a description of their functions: Menu Item Description/Operation Settings (Bold=default) Date set year, month, Press OK and use the UP/DOWN and day keys (to change the setting), then press OK again to go to the next date parameter and repeat, to set the current year, month, and day. Press OK after setting the day to move on and set the Time (next item) Time set hour and Press OK and use the UP/DOWN minute k
Resumen del contenido incluido en la página 11
Menu Item Description/Operation Settings (Bold=default) Mode 1.3M/3M (with Select “Mode” and press OK. Use Mode set to UP/DOWN to select 1P (single 1P or 3P for photo), 3P (burst of 3 photos), or photos), Movie (video mode). Press OK. 5-60 Sec (in Use UP/DOWN to set LO (1.3 MP) Movie (video) or HI (3 MP) still photo resolution mode (High resolution provides better quality photos, low resolution allows you to store more photos on the SD card), or video length from 5-60 sec. (if video m
Resumen del contenido incluido en la página 12
When you’ve finished using the Setup Menu, and are ready to return the camera to normal operating mode, so it will begin to capture photos or videos for you, simply press the Setup button. After you exit the Setup Menu, the display will go blank and the camera is in “sleep” mode. About 30 seconds later, the camera will begin taking photos or videos when triggered, at intervals determined by the trigger delay time setting. Once your camera has been setup, you are ready to begin using it to
Resumen del contenido incluido en la página 13
CAMERA OPERATION (continued) 3. Test the Coverage Area One of the Trail Camera’s most useful features is the ability to test the coverage area. • After mounting the camera, open the front housing and slide the Power switch to the “ON” position. Press the SETUP button if necessary to enter the Setup Menu. • The PIR indicator light below the lens will blink when you have entered the coverage area. • Adjust the camera position as needed and repeat the test until the desired coverage area is
Resumen del contenido incluido en la página 14
VIEWING THE PHOTOS and VIDEOS After your camera has been operating for awhile, you will of course want to review the photos and/or videos it has been capturing. This can be done by either of two methods, according to your preference or the availability of accessory equipment: Using an SD Card Reader 1. Push the SD card in slightly to release it then pull it out gently. 2. Put the SD card into any of the widely available SD card readers (either a dedicated SD card reader or “multi-card reader
Resumen del contenido incluido en la página 15
GLOSSARY PIR (Passive Infrared Sensor): Senses motion like a typical security motion detector. Requires infrared energy (heat) in addition to motion to trigger the sensor to help limit detection to live subjects (rather than leaves, etc). Camera Delay: Time elapsed between photos while events are sensed and recorded. You should set this based on wildlife activity in the area. Moon Phase: The trail cams have a feature which imprints a moon phase stamp on each photo for reference. IR Flash: Al
Resumen del contenido incluido en la página 16
Technical Specifications Model Number 119256CW Image Sensor Type 1/4 Inch CMOS Sensor Resolution 1.3 Megapixels Effective Focal Length 7.6 mm Lens Aperture f/2.0 IR Filter Automatic IR Filter Display LCD (menu screen) PIR Sensor Yes Trigger Speed 1.3 seconds or less Number of IR LED 15 LEDs Max Night Vision Lighting Distance 30 feet Storage SD Card, up to 32 GB Capacity PIR Indicator Yes (Setup mode only) Adjustable Delay Time Range 5~ 59 second, 1~ 10mins (default 10S) Selectable Image Resolut
Resumen del contenido incluido en la página 17
Troubleshooting / FAQ Battery life is shorter than expected 1. Battery life will vary with operating temperature and the number of images taken over time. Typically, the trail cam will be able to capture several thousand images before the batteries die. 2. Check to make sure you have used new alkaline or lithium batteries. Tasco recommends using 4 Energizer® Lithium AA batteries in this Trail Cam to obtain maximum battery life. 3. Make sure that the power switch was turned to the “ON” positi
Resumen del contenido incluido en la página 18
Troubleshooting / FAQ Camera won’t power up 1. Make sure that you have installed all 4 batteries in the battery compartment. Tasco recommends using 4 Energizer® Lithium AA batteries in this trail cam . 2. Make sure that the batteries are installed correctly, observing proper polarity. Always place the negative (flat) end of each battery in contact with the spring tab side of its slot inside the camera. Do not mix old and new batteries. Do not mix battery types-use ALL lithium or ALL alkalin
Resumen del contenido incluido en la página 19
Troubleshooting / FAQ 5. Photos with streaked subject a. In some cases with low lighting conditions and fast moving subjects, the 3 MP resolution setting (“HI”) may not perform as well as the 1.3 MP setting (“LO”). b. If you have multiple images where fast moving subjects produce streaks on the photo, try the “LO” resolution setting instead. 6. Red , green or blue color cast a. Under certain lighting conditions, the sensor can become confused resulting in poor color images. b. If t
Resumen del contenido incluido en la página 20
Troubleshooting / FAQ Camera won’t retain settings 1. Make sure that you have been saving the changes to any parameter settings that you made while in Setup mode, by pressing “OK” after changing the setting. If you don’t save your new setting after changing it, the camera will continue to use the original default setting for that parameter. Do not mix old and new batteries. Do not mix battery types-use ALL lithium or ALL alkaline. Rechargeable batteries are not recommended. 20
