Resumen del contenido incluido en la página 1
3-863-129-11 (1)
Camera Control Unit
Operating Instructions
Before operating the unit, please read this manual thoroughly and retain it for future
reference.
CCU-TX50/50P
© 2004 Sony Corporation
Resumen del contenido incluido en la página 2
Compliance with these directives implies conformity to WARNING the following European standards: • EN60950: Product Safety To prevent fire or shock hazard, do not expose EN55103-1: Electromagnetic Interference (Emission) the unit to rain or moisture. EN55103-2: Electromagnetic Susceptibility (Immunity) To avoid electrical shock, do not open the This product is intended for use in the following cabinet. Refer servicing to qualified personnel Electromagnetic Environment (s): only. E1 (re
Resumen del contenido incluido en la página 3
Table of Contents Overview ................................................................. 4 Function and Location of Parts and Controls .... 5 Front panel .......................................................... 5 Rear panel ........................................................... 9 Connecting the CCU-TX50/50P to the Video Camera .................................................................12 Notes on connections ....................................... 12 Self-Diagnostics ..........
Resumen del contenido incluido en la página 4
Overview The CCU-TX50/50P is a camera control unit that connects to DXC-D50 Series Color Video Cameras via the CA-TX50/50P Camera Adaptor. Features of this unit are described below. Full-featured signal transfer functions The CCU-TX50/50P is able to transfer wide band component video signals. The maximum triaxial cable length that can be used to connect this unit to a camera adaptor is max. 750 m (when using a Belden φ8.5 mm cable) or 1125 m (when using a Belden φ13.2 mm cable). Tra
Resumen del contenido incluido en la página 5
Function and Location of Parts and Controls Front panel a Camera number sheet/tally indicator b POWER switch/CAM and MAIN indicators c CABLE ALARM indicators d INCOM input/output/setting section a Camera number sheet/tally indicator Note Lights red when the red tally signal is input (e.g. when the video signal from the video camera connected to the If the fan in the CCU-TX50/50P stops, the MAIN CCU-TX50/50P goes on air). When the CALL button indicator will flash simultaneously to warn you of t
Resumen del contenido incluido en la página 6
OFF: Turns off the headset microphone. PROD: Producer line. PGM: Outputs the program audio. When this position PRIV: Producer line and engineer line are cut off and is selected, the INCOM level control adjusts input communication is possible only between the CCU- level of the program audio. TX50/50P and the camera connected to the rear panel of the CCU-TX50/50P. INCOM selector ENG: Engineer line. Selects the pathway of intercom signals output/input through the INCOM connector. e CALL button f
Resumen del contenido incluido en la página 7
made with the GAIN control section and SHUTTER changes to the next page. When this button is not lit, the setting section are ignored. self-diagnostics screens are not displayed. l CHARACTER button m MASTER GAMMA adjustment knob Press this button (which lights up when pressed) to Use this knob to adjust the gamma curve. display the self-diagnostics screen on the picture monitor. Each time you press this button, the screen n DETAIL adjustment knob Use this knob to adjust the detail level. o SHU
Resumen del contenido incluido en la página 8
q WHITE/BLACK BALANCE setting section r MASTER BLACK adjustment knob Adjusts the master black levels of the R, G, and B signals simultaneously. The click position of the knob A WHITE controls provides a typical setting. B PRESET button s IRIS setting section A EXT indicator B AUTO button C BLACK controls D AUTO WHITE/BLACK switch E ATW button C IRIS control A WHITE (white balance manual adjustment) A EXT (extender) indicator controls Lights when a lens extender is being used on the video Tur
Resumen del contenido incluido en la página 9
Rear panel a CAMERA connector b AUDIO OUTPUT connectors c INPUT connectors d OUTPUT connectors e REMOTE connector i AC IN connector h WF MODE connector g MIC REMOTE connector f INTERCOM/TALLY/PGM connector a CAMERA connector (triaxial connector) connector is terminated automatically with an Connects to the CA-TX50/50P Camera Adaptor impedance of 75 ohms. attached to the DXC-D50 Color Video Camera using a triaxial cable. A REFERENCE INPUT connectors Caution Do NOT use a defective triaxial cable
Resumen del contenido incluido en la página 10
A REFERENCE INPUT connectors (BNC type) B Y/G, R-Y/R, B-Y/B (component video signal / Accept reference signals (black burst signal) for external RGB output) connectors (BNC type) synchronization. Supply the component signals or the R, G, and B signals for the chroma keyer from each connector. B RET-1/RET-2 (return video signal 1/2) Use the switch on the internal board to select the signals connectors (BNC type) to be output. Accept return video signals from two different systems. For details o
Resumen del contenido incluido en la página 11
i AC IN (AC power input) connector Connects to an AC power source using the supplied AC power cord. Secure the power cord to the CCU-TX50/ 50P using the supplied plug holder. 11 Function and Location of Parts and Controls
Resumen del contenido incluido en la página 12
Connecting the CCU-TX50/50P to the Video Camera When connecting a CCU-TX50/50P to a DXC-D50 Color Video Camera, you must first attach the CA- TX50/50P Camera Adaptor to the video camera. CA-TX50 Triaxial cable DXC-D50 CCU-TX50/50P To an AC power source Notes on connections Triaxial cable The triaxial cable should never be connected to or disconnected from the CCU-TX50/50P when the power is turned on. Always turn the unit off first. Video camera Some switches or controls on the video camera ma
Resumen del contenido incluido en la página 13
Settings of the Camera Self-Diagnostics The settings and operations status of the camera are displayed. The unit allows you to display the status of the unit and the results of a self-diagnosis is of the internal boards of the unit on the screen of a picture monitor connected to the unit. You can display the following status items: Settings of the camera Status display of the unit Results of a self-diagnosis of the internal boards Self-diagnostics of the camera system Setting change
Resumen del contenido incluido en la página 14
CCU-TX50: Model name and format of the camera Page 2 control unit connected. Genlock: External reference signal and its status (lock/unlock) Prompter: Transmission direction of the prompter line Return 1 to 3: Return video signal input status Self-diagnostics of the Camera System Press the CHARACTER button when the status display of the unit is displayed. Page 1 of the self-diagnostics display is displayed. The results of a self-diagnosis of the camera system are CAMERA cable: Camera cable
Resumen del contenido incluido en la página 15
Each time you press the CHARACTER button, another AT board page of results is displayed in turn. DM board Reference: Operation mode of the phase adjustment Gen Lock: Locking status BATT Volt: Voltage of the coin battery supplied with CAM Video: Reception status of the video signals the AT board from the camera. CCU Mode: Operation mode of the CCU Skin Gate: Reception status of the Skin gate signal PLD Config.: Configuration result status of the PLD from the camera mounted on the AT board TRI
Resumen del contenido incluido en la página 16
IV board Diagnostics Page of the Camera Return: Setting status of the return signal input The results of the diagnosis of each board of the camera connectors to the return channels from 1 to 3 are displayed. Return Signal: Status of the return video input signal Rear CN: Power supply status of the CN board on the rear Exiting the Self-diagnostic Mode PLD Config: Configuration completion status of the PLD mounted on the IV board Display the last “ROM Version” page, and then press the Power:
Resumen del contenido incluido en la página 17
Notes on Use Specifications Use and storage locations General Avoid using or storing the unit in the following places: Power consumption Where it is subject to extremes of temperature 100 - 240 V AC, 50/60 Hz, (operating temperature: +5ºC to +40ºC (41ºF to maximum 1.3 A 104ºF)). Peak inrush current Note that in summer the temperature in a car with the (1) Power ON, current probe method: windows closed can reach 50ºC (122ºF). 50 A (240V) Very damp or dusty places. (2) Hot switching inrus
Resumen del contenido incluido en la página 18
PAL: 700 mVp-p, 75 ohms Encoded output: 1.0 Vp-p, 75 ohms WF MODE 4-pin (1) AUDIO OUTPUT XLR, 3-pin 0 dBu/–20 dBu, balanced, 2 channels SYNC BNC type 2) R/G/B/and Y/R-Y/B-Y are switchable. Camera input/output signals CAMERA Triax (Kings type for the U.S.A. and Canada, Fischer type for Europe) COAX BNC type (1), 75 ohms REMOTE 10-pin, multi connector INTERCOM/TALLY/PGM D-sub, 25-pin (1) 4W/RTS TALLY: 24 V DC, TTL level or contact selectable MIC REMOTE D-sub, 15-pin (1) INCOM (on the front panel
Resumen del contenido incluido en la página 19
Sony Corporation
