Resumen del contenido incluido en la página 1
OWNER’S OPERATING MANUAL
DTV-940/943
DTV Capable CRT Projector
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS TABLE OF CONTENTS............................................................................................................................1 SAFETY INSTRUCTIONS ................................................................................................................................1-1 On safety.............................................................................................................................................................1-1 On installation .
Resumen del contenido incluido en la página 4
TABLE OF CONTENTS RANDOM ACCESS ADJUSTMENT MODE ..................................................................................................6-1 Starting up the Random Access Adjustment mode ............................................................................................6-1 Overview ‘Random Access Adjustment’ mode ...................................................................................................6-1 Selecting Setup Pattern ........................................
Resumen del contenido incluido en la página 5
TABLE OF CONTENTS Hardware Configuration .........................................................................................................................................9-1 How to format the control data...............................................................................................................................9-1 Sending a RECORD (single instruction)................................................................................................................9-2 Exam
Resumen del contenido incluido en la página 6
TABLE OF CONTENTS Error Messages..................................................................................................................................................10-13 No Pattern Error .................................................................................................................................................10-14 Status Reporting Forced Break.......................................................................................................................
Resumen del contenido incluido en la página 7
SAFETY INSTRUCTIONS Notice on Safety FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 This equipment has been tested and found to comply with the lim- No.950, which are the safety standards of information technology its of a class B digital device, pursuant to Part 15 of the FCC equipment including electrical business equipment. Rules. These limits are designed to prov
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
LOCATION AND FUNCTION OF CONTROLS This device complies with part 15 of RS232 IN RS232 OUT IR COMM PORT REMOTE R G(s) B H V VIDEO S - VIDEO the FCC rules. Operation is subject to following two conditions (1), This device may not cause harmful inter- ferance, and (2) this device must accept any interferance received including interferance that may cause undesired operation. 6 2 4 1 3 5 78 VIDEO Input (Composite video, 1x BNC connector): RS 232 Input Port 7 1 Allows a vi
Resumen del contenido incluido en la página 10
LOCATION AND FUNCTION OF CONTROLS IR Transmission Indicator 1 ADJ. : Adjust key, to enter or exit the adjustment mode. 2 stand-by color Address key (recessed key) : to enter the address of the projec- 3 tor (between 0 and 9). Press the address key, followed by press- pause / park brightness ing one digit button between 0 and 9. When addressed to O , the remote will talk to any projector, regardless of its address. STBY : Stand by button: 4 contrast sharpness - To initiate remote power up operat
Resumen del contenido incluido en la página 11
CONNECTIONS AC Power (mains) Cord Connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector on the front of the projector. See installation instructions before connecting to the supply V NOM 120/230 Volt I MAX 5/2.5 AMP FREQ 60/50 Hz OFF ON Power Check The power voltage is determined by the sticker on the front of the projector. Warning! Verify the power voltage corresponds to that of the wall outlet. If the wa
Resumen del contenido incluido en la página 12
Connections This device complies with part 15 of RS232 IN RS232 OUT IR COMM PORT REMOTE R G(s) B H V VIDEO S - VIDEO the FCC rules. Operation is subject to following two conditions (1), This device may not cause harmful inter- ferance, and (2) this device must accept any interferance received including interferance that may cause undesired operation. 1 23 GENERAL Location Projector input ACCESS AVAILABLE FROM LOCAL KEYPAD MENU ITEMS 2 Comp. Video 1 Composit
Resumen del contenido incluido en la página 13
Resumen del contenido incluido en la página 14
Resumen del contenido incluido en la página 15
Connections Connecting a Component source. This device complies with part 15 of RS232 IN RS232 OUT IR COMM PORT REMOTE R G(s) B H V VIDEO S - VIDEO the FCC rules. Operation is subject to following two conditions (1), This device may not cause harmful inter- ferance, and (2) this device must accept any interferance received including interferance that may cause undesired operation. (R-Y)Y(B-Y) analog input terminals with sync input or with sync on the luminance (Y) inp
Resumen del contenido incluido en la página 16
Connections (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) input selection GENERAL ACCESS a. With the RCU: Select “Component” in the Source Selection Menu SHARPNESS TINT 56 COLOR 34 BRIGHTNESS b. With the local keypad : 12 CONTRAST (to gain access to the local keypad, see ‘Local keypad’ in chapter Enter ADJUST ‘Location and function of controls’.) Select with , -Press ADJUST key, the General access menu is displayed on the or then . screen. -Use the control disk to highlight 6. to
Resumen del contenido incluido en la página 17
CONTROLLING The DTV-94943 can be controlled with c. Using your RCU. a. The RCU b. The hardwired RCU (cable not included) Before using your RCU, it is necessary to enter the projector address into c. The local keyboard the RCU (only when that address is between 1 and 9). The projector with the corresponding address will listen to that specific RCU. The procedure and results of controlling the projector with either of these When address 0, ‘zero address’ is programmed into the RCU, every pro- RCU
Resumen del contenido incluido en la página 18
Controlling Input selection. down, push the control disk to the left or to the right to move the cursor to the left and to the right. Press ENTER to confirm your selection. GENERAL ACCESS MENU ITEMS When a valid and available source is selected, there will be information SOURCE Projector input displayed on the screen about that source. This information includes : - Source number - Horizontal frequency 1 Comp. Video - Vertical frequency 2 S - Video 3 RGBS or RGsB 4 RGB3S or RG3sB Source 2 5 (
Resumen del contenido incluido en la página 19
Resumen del contenido incluido en la página 20
START UP OF THE ADJUSTMENT MODE Adjustment mode All picture geometry and convergence adjustments are made while in the ‘Adjustment mode’. Two possible ways to enter the adjustment mode: a) Using the RCU. Press the ADJUST key. The projector displays the path selection menu. b) Using the local keypad. Press the ADJUST key. The projector displays the General access menu. Use the control disc to highlight enter ADJUST and press ENTER. The path EXIT ADJUST selection menu will be displayed. STANDBY EN
