Resumen del contenido incluido en la página 1
EN User manual
Gas hob
ZGG649
IL
Resumen del contenido incluido en la página 2
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Helpful hints and tips _ _ _ _ _ _ _
Resumen del contenido incluido en la página 3
• This appliance is not connected to a combustion prod- Installation ucts evacuation device. It must be installed and con- • You must read these instructions. The manufacturer is nected in accordance with current installation regula- not responsible for any injury to persons and pets or tions. Particular attention must be given to the relevant damage to property caused by failure to obey these re- requirements regarding ventilation. quirements. • The use of a gas cooking appliance cause heat and
Resumen del contenido incluido en la página 4
– Speak to your local authorised facilities for disposal of your appliance. Installation Liquid gas: use the rubber pipe holder. Always engage the Warning! The following instructions about gasket. Then continue with the gas connection. The flexi- installation, connection and maintenance must be ble pipe is prepared for apply when: carried out by qualified personnel in compliance with standards and local regulations in force. – it can not get hot more than room temperature, higher than 30°C; Gas
Resumen del contenido incluido en la página 5
• Any electrical component must be installed or replaced Adjustment of minimum level by the Service Force Centre technician or qualified To adjust the minimum level of the burners: service personnel. 1. Light the burner. • Always use a correctly installed shockproof socket. 2. Turn the knob on the minimum position. • Make sure that there is an access to the mains plug af- 3. Remove the control knob. ter installation. 4. With a thin screwdriver, adjust the by-pass screw po- • Do not pull the main
Resumen del contenido incluido en la página 6
a) Removable panel b) Space for connections A Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a con- tinuous supply of air. The electrical connection of the hob B and the oven must be installed separately for safety rea- sons and to let easy remove oven from the unit. A - supplied seal B - supplied brackets 2 2 Possibilities for insertion 50 cm 120 cm Kitchen unit with door The panel installed below the hob must be
Resumen del contenido incluido en la página 7
Product description Cooking surface layout 2 1 1 Semi-rapid burner 2 Semi-rapid burner 3 3 Control knobs 4 Auxiliary burner 5 5 Rapid burner 4 Control knobs Symbol Description ignition position / maximum gas Symbol Description supply no gas supply / off position minimum gas supply Operation Ignition of the burner Warning! Be very careful when you use open fire in 1 kitchen environment. Manufacturer decline any responsibility in case misuse of the flame 2 Always light the burner before you put co
Resumen del contenido incluido en la página 8
Important! In the absence of electricity you can ignite the Turning the burner off burner without electrical device; in this case approach the To put the flame out, turn the knob to the symbol . burner with a flame, push the relevant knob down and turn Warning! Always turn the flame down or switch it off it counter-clockwise to maximum gas release position. before you remove the pans of the burner. If the burner accidentally goes out, turn the control knob to the off position and try to light t
Resumen del contenido incluido en la página 9
• Make sure you position the pan supports correctly after 3. At the end rub the appliance dry with a clean cloth. cleaning. In order to properly place the pan supports, make sure that the arms of the pan support are positioned in corre- • To make burners work correctly, make sure that the spondence with the hole placed at the base of the burner. arms of the pan supports are in the centre of the burn- This way, the pan support will be stable and fixed. er. • Be very careful when you replace the p
Resumen del contenido incluido en la página 10
If there is a fault, first try to find a solution to the problem neer, the visit from the customer service technician or yourself. If you cannot find a solution to the problem dealer may not take place free of charge, even during the yourself, speak your dealer or the local Service Force warranty period. Centre. Labels supplied with the accessories bag If you operated the appliance incorrectly, or the in- Stick the adhesive labels as indicated below: stallation was not carried out by a registere
Resumen del contenido incluido en la página 11
Appliance class: 3 Burner Ø By-pass in 1/100 mm Semi-rapid 35 By-pass diameters Rapid 45 Burner Ø By-pass in 1/100 mm Auxiliary 28 Gas burners BURNER NORMAL POWER NORMAL POWER LPG (Butane/Propane) G30/31 (3B/P) 30/30 mbar kW kcal/h inj. 1/100 mm g/h Auxiliary burner 0.95 814 50 75 Semi-rapid burner 1.6 1368 66 126 Rapid burner 2.45 2095 77 193 Environment concerns information about recycling of this product, please contact The symbol on the product or on its packaging your local council, your h
Resumen del contenido incluido en la página 12
www.zanussi.com/shop 397195501-B-2010
