Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTIONS AND ADVICE FOR THE
USE, INSTALLATION AND MAINTENANCE
OF BUILT-IN ELECTRIC HOBS
Dear Customer,
Thank you for having purchased one of our products.
We are certain that this new, modern, functional and practical appliance, built with the very
highest quality materials, will meet your requirements in the best possible way. This hob is easy
to use. It is, however, important to thoroughly read the instructions in this handbook in order to
obtain the best results.
The manufacturer shall n
Inhaltszusammenfassung zur Seite Nr. 2
DESCRIPTION OF THE HOT PLATES TYPE: PFZ 02 4 Plate Ø 145 of 1000 ÷ 1500 W 5 Plate Ø 180 of 1500 ÷ 2000 W 11 Control knob for electric plate n° 4 12 Control knob for electric plate n° 5 13 Warning light indicating that one or more plates are operating 2
Inhaltszusammenfassung zur Seite Nr. 3
USE A red warning light will come on to indicate that the 1) SWITCHING ON THE ELECTRIC plate has been ignited. PLATES The hobs may be equipped with two types of 2) HOW TO USE THE ELECTRIC PLATES electric plates: normal and rapid plates indicated by A purely indicative plate regulation chart is given a red mark. The normal plates and the rapid plates below. are controlled by a 7 - position switch (see fig. 1). Switch on the plates by turning the knob to the required position. A diagram is screen-
Inhaltszusammenfassung zur Seite Nr. 4
USE WARNINGS: when the plate is switched on for the first time, or if it has remained unused for a long period, it should be dried for 30 minutes on switch position n° 1. This will eliminate any moisture that may have been absorbed by the insulating material. To correctly use the appliance, remember: - to place a pan on the plate before switching this on. - To always use pans with flat and very thick bottoms (see fig. 2). - To never use pans that are smaller than the plate diameters. - To dry t
Inhaltszusammenfassung zur Seite Nr. 5
CLEANING WARNINGS: IMPORTANT: always disconnect the appliance from the - correctly preserve the plate after use by electricity main before carrying out any cleaning treating it with special products, easily operation. available on the market. This will keep the surface of the plate clean and bright. The 3) HOTPLATE operation will also prevent the formation of If you want to preserve the surface clean and bright, rust. periodically wash the hot plate with lukewarm soapy - Any liquid overflowed th
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION Installation and maintenance must only be that the transparent protection still adheres to the carried out by a qualified installer. seal itself. Incorrect installation could cause damage to - Overturn the hob and correctly position seal “E” persons, animals and property for which the (fig. 5) under the edge of the hob itself, so that manufacturer cannot be held responsible. the outer part of the seal itself perfectly matches the outer perimetral edge of the hob. The ends of the str
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION When the appliance is connected straight to the 6) ELECTRICAL CONNECTIONS electricity main: Electrical connection must be carried out in compliance with the specifications and - install an omnipolar cutout between the provisions in force. appliance itself and the main. This circuit-breaker Before proceeding with the connections, check that: should be sized according to the rating of the - the voltage rating of the appliance and the appliance and the opening between its contacts curr
Inhaltszusammenfassung zur Seite Nr. 8
SERVICING Always disconnect the appliance from the N.B. In case of substitution of the input cable, electricity main before proceeding with any the installer must keep the “earth” conductor servicing operation. longer than “live” ones, and must respect the cautions in paragraph “Electrical connection”. 7) REPLACING THE ELECTRICAL To reassemble the appliance repeat the inverse COMPONENTS process. For access to the various parts, remove the hotplate 8) TECHNICAL CHARACTERISTICS OF from the top of
Inhaltszusammenfassung zur Seite Nr. 9
TECHNICAL DATA MODEL WITH 2 NORMAL PLATES VOLTAGE 230 - 240 V~ FREQUENCY 50/60 Hz TOT. RATING 2500 W MODEL WITH 2 RAPID PLATES VOLTAGE 230 - 240 V~ FREQUENCY 50/60 Hz TOT. RATING 3500 W 9
Inhaltszusammenfassung zur Seite Nr. 10
TECHNICAL ASSISTANCE AND SPARE PARTS This appliance, before leaving the factory, has been carefully tested and regulated by expert and specialized personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention. For this reason, always contact your Dealer or your nearest After Sales Centre whenever repairs or adjustments are required, specifying the type of faul
