Inhaltszusammenfassung zur Seite Nr. 1
PZ 640T GH NG and PZ 750R GH NG
Operating, Care and
Installation Instructions
Contents
Safety Warnings 2
Using Your Cooker 3
Installation 4-5
Service Details 6
Troubleshooting 7
Care And Maintenance 8
Installer - Ensure these instructions remain with the consumer.
This cooktop has been certifi ed for use by SAI-Global
Inhaltszusammenfassung zur Seite Nr. 2
Safety Warnings This appliance has been designed and manufactured The appliance must not be installed outdoors, even in in compliance with Australian and international safety covered areas. It is extremely dangerous to leave the ap- standards. The following warnings are provided for safety pliance exposed to weather. reasons and must be read carefully. Always make sure the knobs are in the OFF position when DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS the appliance is not in use. APPLIANC
Inhaltszusammenfassung zur Seite Nr. 3
Using Your Cooker Controlling the burners Lighting the burners for the fi rst time Each control knob is marked to indicate which burner it If the appliance is being used for the fi rst time, or if it has not controls. Each control knob also has markings to indicate the been used for a long period of time, it may be necessary to three main settings: purge the gas lines of excess air before you can successfully light the burners. OFF To do this, turn each burner to high for 10-15 seconds and
Inhaltszusammenfassung zur Seite Nr. 4
Installation WARNING: Before installation, check that the gas type (natu- Fitting the cooktop into cabinetry ral gas or LPG/Propane) of the cooker is suitable for the gas The following minimum clearances to combustible materials type available to the installation. It is extremely dangerous to must be observed: use the wrong gas type with any appliance, as fi re or serious Minimum clearance from edge of burner to side wall must injury can result. be 200 mm. These instructions have been prepa
Inhaltszusammenfassung zur Seite Nr. 5
Installation Fitting the cooktop above an oven Electrical connection When installing the cooktop above an oven, both the electric- The electrical supply for the cooktop must be a 240 Volt 50 ity supply cable and the gas pipe or fl exible hose must not Hz. touch hot parts of the oven housing. The fuse and electrical wiring of the home/premises must When installing above a built-under oven without forced cool- support the load of the appliance. ing ventilation, suitable air vents should be prov
Inhaltszusammenfassung zur Seite Nr. 6
Service Details Post installation checks Electrical equipment and components Leak Check To check or replace the ignition module Ensure all gas control knobs are in the Off position. Electrical components are located below the hob surface. To access the components: Ensure the gas supply is switched on. IMPORTANT: First ensure that gas and electrical power Spray a solution of soapy water onto all gas joints as well are disconnected before performing any service to this as the full length o
Inhaltszusammenfassung zur Seite Nr. 7
Troubleshooting It may happen that the appliance does not function properly or at all. Before calling the service centre for assistance, check if anything can be done. First, check to see that there are any interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open. Problem Likely cause The burner does not light or the fl ame is not even around the The gas holes on the burner are clogged. burner. The removable parts that make up the burner a
Inhaltszusammenfassung zur Seite Nr. 8
Care And Maintenance General cleaning notes Ignitors DO NOT TOUCH HOT SURFACES, ALLOW COOKTOP TO The terminal part of the electronic instant lighting devices COOL COMPLETELY BEFORE CLEANING. should be cleaned frequently, Always wipe spills up when they occur. Do not leave spills Enamelled parts (trivets) to dry onto the surface of the hob. Never use abrasives, scouring pads or sharp objects. This It is usually enough to wash the hob with a d
