Inhaltszusammenfassung zur Seite Nr. 1
Installation Above the
Instructions Cooktop Oven
Model JVM1665
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• Note to Consumer – Keep these instructions
for future reference.
•
IMPORTANT – Save these
•Skill level – Installation of this appliance requires basic
instructions for local inspector’s use.
mechanical and electrical skills.
•
IMPORTANT –Observe all
•Proper installation is the responsibil
Inhaltszusammenfassung zur Seite Nr. 2
Installation Instructions Recirculating ................................................ 19–22 C CONTENTS Attach Mounting Plate to Wall ................19 General information Preparation of Top Cabinet ......................19 Important Safety Instructions ...................................... 3 Adapting Blower for Electrical Requirements .................................................. 3 Recirculation ........................................20, 21 Hood Exhaust ..............................
Inhaltszusammenfassung zur Seite Nr. 3
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is on the power outlet box before beginning the properly grounded. installation to insure that the outlet box is properly Where a standard two-prong wall receptacle is grounded. If not properly grounded, or if the outlet enco
Inhaltszusammenfassung zur Seite Nr. 4
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft. (6″ Round) Rectangular-to-Round 5 Ft. x (1) = 5
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions NOTE: If you need to install ducts, note that the total duct Maximum duct length: 1 length of 3 ⁄ 4″ x 10″ rectangular or 6″ diameter round duct For satisfactory air movement, the total duct length 1 should not exceed 120 equivalent feet. of 3 ⁄ 4″ x 10″ rectangular or 6″ diameter round duct Outside ventilation requires a HOOD EXHAUST DUCT. should not exceed 120 equivalent feet. Read the following carefully. Elbows, transitions, wall and roof caps, etc., NOTE: It is
Inhaltszusammenfassung zur Seite Nr. 6
Installation Instructions PARTS INCLUDED DAMAGE – SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return PART QUANTITY the unit to the store in which it was bought for repair or replacement. Top Cabinet 1 Template • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must Rear Wall 1 be made by arrangement between customer
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 and #2 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors 3 7 3 Electric drill with ⁄16″, ⁄16″, ⁄8″, (to cut template, if necessary) 1 5 ⁄2″ and ⁄8″ drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (opti
Inhaltszusammenfassung zur Seite Nr. 8
Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE REMOVING THE OVEN FROM THE FINDING THE WALL STUDS A. B . CARTON/REMOVING THE MOUNTING PLATE Remove the turntable, installation instructions, 1 filters, exhaust Adapter, damper, shelf and the small hardware bag. Do not remove the Styrofoam Wall protecting the front of the oven. Studs Fold back all 4 carton flaps fully against carton 2 sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting Ce
Inhaltszusammenfassung zur Seite Nr. 9
At least 30″, up to 36″ Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath framed recessed Plate position – beneath flat bottom cabinet bottom cabinet Mounting Plate Tabs Mounting Plate Tabs Touching the Cabinet Touching the Back Bottom Frame 30″ to Cooktop Plate position – beneath recessed bottom Your cabinets may have decorative trim that interferes cabinet with front overhang with the oven installation. Remove the decorative trim to i
Inhaltszusammenfassung zur Seite Nr. 10
Installation Instructions ALIGNING THE WALL PLATE D. Hole B Draw a Vertical Line on Wall Hole A from Center of Top Cabinet Hole C Hole D Area E CAUTION: Wear gloves to NOTE: Appearance and avoid cutting fingers on shape of the mounting sharp edges. plate may vary from your model. Draw a vertical line on the wall at the center of the 30″ NOTE: Holes C and D are inside area E. If neither C nor D 1 wide space. is in a stud, find a stud somewhere in area E and draw a fifth circle to line up with th
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following three NOTE: This oven is shipped assembled for Outside Top types of ventilation: Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed A. Outside Top Exhaust (Vertical Duct) to that section. B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST A B (
Inhaltszusammenfassung zur Seite Nr. 12
Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adapter A4. Mount Oven A5. Adjust Exhaust Adapter A6. Connect Ductwork To use toggle bolts: A1. ATTACH THE MOUNTING PLATE Spacing for Toggles TO THE WALL More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End Place the mounting plate against the wall 3 and insert the toggle wings into the holes Attach the plate to the
Inhaltszusammenfassung zur Seite Nr. 13
Installation Instructions A2. USE TOP CABINET TEMPLATE FOR A4. MOUNT THE OVEN PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adapter. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to
Inhaltszusammenfassung zur Seite Nr. 14
Installation Instructions MOUNT THE OVEN (continued) ADJUST THE EXHAUST ADAPTER A4. A5. Open the top cabinet and adjust the exhaust adapter Cabinet Front to connect to the house duct. Cabinet Bottom Shelf Filler Block Damper Equivalent to Depth of Cabinet Back of Recess Oven Self-Aligning Screw Oven Top 3 Attach the oven to the top cabinet by inserting 3 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Be sure to keep power cord tight. Be careful not
Inhaltszusammenfassung zur Seite Nr. 15
Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Exhaust Adapter to Wall Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Oven PREPARING THE REAR WALL ATTACH THE EXHAUST ADAPTER B1. B2. FOR OUTSIDE BACK EXHAUST TO THE OVEN REAR PANEL You need to cut an opening in the rear wall for outside 1 Unscrew and remove the exhaust adapter assembly exhaust. from the top of the oven. Ex
Inhaltszusammenfassung zur Seite Nr. 16
Installation Instructions B4. USE TOP CABINET TEMPLATE FOR B3. ATTACH THE MOUNTING PLATE PREPARATION OF TOP CABINET TO THE WALL You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 Remove the toggle wings from the bolts. • Read the instructions on the TOP CABINET TEMPLATE. 2 Insert the bolts into the mounting plate t
Inhaltszusammenfassung zur Seite Nr. 17
Installation Instructions ADAPTING BLOWER FOR 5 Place the blower unit back into the opening. B5. OUTSIDE BACK EXHAUST AFTER: Fan Remove the two screws that hold the blower plate Blade Openings 1 Facing Back and remove the screw holding the blower motor to the oven. Slide blower plate from under its retaining flange. Retaining Flange Blower Plate CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exha
Inhaltszusammenfassung zur Seite Nr. 18
Installation Instructions Cabinet Front B6. MOUNT THE OVEN Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. Oven Top IMPORTANT: Do not grip or use handle 3 Attach the oven to the top cabinet by inserting during installation. 3 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Be sure NOTE: If your cabinet is metal, use t
Inhaltszusammenfassung zur Seite Nr. 19
Installation Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter Place the mounting plate against the wall 3 C1. ATTACH THE MOUNTING PLATE and insert the toggle wings into the holes in the wall to mount the plate. TO THE WALL NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet whe
Inhaltszusammenfassung zur Seite Nr. 20
Installation Instructions 4 Roll the blower unit 90° so that fan blade openings C3. ADAPTING BLOWER are facing toward the front of the oven. FOR RECIRCULATION BEFORE: Fan Blade NOTE: The exhaust Adapter with damper is not Openings Facing Up needed for recirculating models. You may want to save them for possible future use. 1 Remove and save screws that hold blower plate and blower unit to the oven. Blower Plate Screws Blower Plate Roll Back of Oven Blower Motor Screw Slide the blower plate from
