Inhaltszusammenfassung zur Seite Nr. 1
Q20wb
LCD Display
Model No. : VS11674
Inhaltszusammenfassung zur Seite Nr. 2
Contents TCO Information.......................................................................................... i Compliance Information.............................................................................. 1 Important Safety Instructions...................................................................... 2 Declaration of RoHS Compliance............................................................... 3 Copyright Information ............................................................
Inhaltszusammenfassung zur Seite Nr. 3
TCO Information Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics Good visual ergonomics and image quali
Inhaltszusammenfassung zur Seite Nr. 4
Compliance Information For U.S.A. This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
Inhaltszusammenfassung zur Seite Nr. 5
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions. 7. Do not block any ventilati
Inhaltszusammenfassung zur Seite Nr. 6
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% M
Inhaltszusammenfassung zur Seite Nr. 7
Copyright Information ® Copyright © ViewSonic Corporation, 2007. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards As
Inhaltszusammenfassung zur Seite Nr. 8
Getting Started ® Congratulations on your purchase of a ViewSonic LCD display. Important! Save the original box and all packing material for future shipping needs. NOTE: The word “Windows” in this user guide refers to the following Microsoft operating systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me (Millennium), and Windows XP. Package Contents Your LCD display package includes: •LCD display • Power cord • Video cable • ViewSonic Wizard CD-ROM • Quick Start Guide NOTE:
Inhaltszusammenfassung zur Seite Nr. 9
Quick Installation 1. Connect power cord (and AC/DC • Wait for the CD-ROM to auto-start. adapter if required) NOTE: If the CD-ROM does not auto- start: double-click on the CD-ROM icon in 2. Connect video cable the Windows Explorer, then double-click • Make sure both the LCD display and on viewsonic.exe. computer are turned OFF • Follow the on-screen instructions. • Remove rear panel covers if necessary 5. Windows users: Set the timing mode • Connect the video cable from the LCD (resolution
Inhaltszusammenfassung zur Seite Nr. 10
Wall Mounting (Optional) ® To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk- mounted to a wall-mounted display, do the following: 1. Verify that the Power button is turned Off, then Four VESA screw holes disconnect the power cord. 2. Lay the LCD display face down on a towel or blanket. 3. Remove the Plastic Covers from the back of the LCD display. 4. Remove the four
Inhaltszusammenfassung zur Seite Nr. 11
Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1680 x 1050) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1680 x 1050 @ 60Hz. To set the Timing Mode: 1.
Inhaltszusammenfassung zur Seite Nr. 12
Adjusting the Screen Image Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 11. Main Menu with OSD controls Front Control Panel shown below in detail Standby Power On/Off Displays the control screen for Power light the highlighted control. Green = ON Also toggles between two controls on some screens. Orange = Power Saving Also
Inhaltszusammenfassung zur Seite Nr. 13
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2. To select a control to adjust, press or to scroll up or down in the Main Menu. 3. After the desired control is selected, press button [2]. A control screen like the one shown below appears. The command line at the bottom of the control s
Inhaltszusammenfassung zur Seite Nr. 14
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust sizes and centers the screen image automatically. Contrast adjusts the difference between the image background (black level) and the foreground (white level). Brightness adjusts background black level of the screen image. Color Adjust provides several color adjustment modes, including preset color temperatures and a User Color mode which allows independent adjustment o
Inhaltszusammenfassung zur Seite Nr. 15
Control Explanation Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and ® the ViewSonic website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency). NOTE: VESA 1680 x 1050 @ 60Hz (recommended) means that the resolution is 1680 x 1050 and the refresh rate is 60 Hertz. Manual Image Adjust Horizontal Size adjusts the width of th
Inhaltszusammenfassung zur Seite Nr. 16
Control Explanation Setup Menu displays the menu shown below: Language Select allows the user to choose the language used in the menus and control screens. Resolution Notice allows the user to enable or disable this notice. If you enable the Resolution Notice shown above and your computer is set at a resolution other than 1680 x 1050, the following screen appears. OSD Position allows the user to move the OSD menus and control screens. OSD Timeout sets the length of time the OSD screen is displ
Inhaltszusammenfassung zur Seite Nr. 17
Other Information Specifications LCD Type 20” (full 20" viewable diagonal area), TFT (Thin Film Transistor), Active Matrix WSXGA+ LCD, 0.258 mm pixel pitch Color Filter RGB vertical stripe Glass Surface Anti-Glare Input Signal Video RGB analog (0.7/1.0 Vp-p, 75 ohms) Sync Composite Sync, Separate Sync, Sync on Green f :24-82 kHz, f :50-75 Hz h v TMDS Digital f :24-82 kHz, f :50-75 Hz h v Compatibility PC Up to 1680 x 1050 Non-interlaced 1 Power Macintosh up to 1680 x 1050 Macintosh Resolution Re
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting No power • Make sure power button (or switch) is ON. • Make sure A/C power cord is securely connected to the LCD display. • Plug another electrical device (like a radio) into the power outlet to verify that the outlet is supplying proper voltage. Power is ON but no screen image • Make sure the video cable supplied with the LCD display is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the
Inhaltszusammenfassung zur Seite Nr. 19
Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. T = Telephone Country/Region Website Email F = FAX T= 800 688 6688 United States www.viewsonic.com service.us@viewsonic.com F= 909 468 1202 T= 866 463 4775 Canada www.viewsonic.com service.ca@viewsonic.com F= 909 468 5814 T= 866 323 8056 Latin America www.viewsonic.com soporte@viewsonic.com (Mexico/Chile) F= 909 444 5655 www.viewsoniceurope.com/
Inhaltszusammenfassung zur Seite Nr. 20
Cleaning the LCD Display • MAKE SURE THE LCD DISPLAY IS TURNED OFF. • NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE. To clean the screen: 1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles. 2. If the screen still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. To clean the case: 1. Use a soft, dry cloth. 2. If the case still not clean, apply a sm
