Inhaltszusammenfassung zur Seite Nr. 1
Touchcomputer User Guide
17A2 17" LCD Multifunction Touchcomputer
Inhaltszusammenfassung zur Seite Nr. 2
Elo TouchSystems Touchcomputer User Guide 17" LCD Multifunction Touchcomputer ESY17A2 Revision D P/N E926979 Elo TouchSystems 1-800-557-1458 www.elotouch.com
Inhaltszusammenfassung zur Seite Nr. 3
Copyright c 2008 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no re
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents Chapter 1 Using the I/O panel ..................................... 29 Setup 6 USB and Powered USB ........................ 29 Unpacking Your Touchcomputer ......................... 6 Cash Drawer ......................................... 29 Product Overview ................................................ 7 Ethernet ................................................ 29 Front View ..................................................... 7 Serial ..................................
Inhaltszusammenfassung zur Seite Nr. 5
Fingerprint Reader................................... 51 Barcode Scanner ...................................... 52 Speaker Bar .............................................. 53 DVD Drive ................................................ 54 Wireless Card ........................................... 55 TV Tuner .................................................. 55 Environmental Specifications.......................... 56 Temperature Ranges ................................ 56 Humidity ...............
Inhaltszusammenfassung zur Seite Nr. 6
C H A P T E R 1 Setup This chapter discusses how to set up and test your touchcomputer and any included peripheral options. Unpacking Your Touchcomputer Check that the following items are present and in good condition: OR Touchcomputer Power cable US/Canadian European power cable PS/2 Y-cable DB9 adapter cable CD and Quick Install Guide Power Adapter Elo TouchSystems 17A2 User Guide 6
Inhaltszusammenfassung zur Seite Nr. 7
Product Overview Front View Rear View Note: Shown with optional peripherals Elo TouchSystems 17A2 User Guide 7
Inhaltszusammenfassung zur Seite Nr. 8
Side View Note: Shown with optional peripherals Base Bottom View Elo TouchSystems 17A2 User Guide 8
Inhaltszusammenfassung zur Seite Nr. 9
Display Orientation Elo TouchSystems 17A2 User Guide 9
Inhaltszusammenfassung zur Seite Nr. 10
Display Orientation with Peripherals Elo TouchSystems 17A2 User Guide 10
Inhaltszusammenfassung zur Seite Nr. 11
Initial Turn-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touchcomputer hardware configuration and connected devices. To setup the Windows OS for the touchcomputer, turn on the touchcomputer and follow the instructions on the screen. Language Selection When the following window appears, you have the option of changing the language used in menus and dialogs. Click Customize. The Regional and Language window shown below w
Inhaltszusammenfassung zur Seite Nr. 12
Select the Language tab. The window shown below will appear. Select the desired language in the drop-down list labeled Language used in menus and dialogs. Elo TouchSystems 17A2 User Guide 12
Inhaltszusammenfassung zur Seite Nr. 13
Time-zone selection When the following window appears, you may change the time-zone, date, and/or time of the touchcomputer. After making any changes, click Next to finish. Windows Setup will complete the initialization of the touchcomputer. Elo TouchSystems 17A2 User Guide 13
Inhaltszusammenfassung zur Seite Nr. 14
Test Devices The touchcomputer can be pre-installed with several different hardware options. To test an optional device that is installed on the touchcomputer, follow the instructions below. NOTE: Testing icons are located on the desktop. Testing of a particular device can only be done after the device is properly installed. Testing the Touchscreen The touchscreen is pre-calibrated for accurate touch response. Calibration* If for any reason the touchscreen needs to be re-calibrated, double-click
Inhaltszusammenfassung zur Seite Nr. 15
Testing the Magnetic Stripe Reader (MSR) (optional) Testing in USB MSR Keyboard (KB) Emulation Mode 1. Double-click the KB MSR Test icon to open the Notepad application 2. Slide the card through the MSR and verify that the data is displayed in the application window. Testing in USB MSR Human Interface Device (HID) Mode 1. Double-click the HID MSR Test icon to start the test application. 2. Click the Read Cards button. 3. Slide the card through the MSR and verify that the data is displayed in the
Inhaltszusammenfassung zur Seite Nr. 16
Converting MSR from Keyboard Emulation to HID and vice versa 1. Double-click the MSR Change Mode icon to start the switch application. 2. Click on HID Mode to switch to HID mode OR click on Keyboard Mode to switch to Keyboard mode. The dimmed box will indicate the current setting. 3. Click Quit to close the window. Elo TouchSystems 17A2 User Guide 16
Inhaltszusammenfassung zur Seite Nr. 17
Testing the Customer Display (optional) 1. Double-click the CustDisplay Test icon. 2. Verify that the device shows "EloTouch Systems Customer Display" on the display. Elo TouchSystems 17A2 User Guide 17
Inhaltszusammenfassung zur Seite Nr. 18
Testing the Finger Print Reader (optional) 1. Double-click the Fingerprint Reader Test icon to start the test application. 2. Place your finger on the fingerprint reader sensor and verify that the image of your fingerprint is displayed on the application window. Elo TouchSystems 17A2 User Guide 18
Inhaltszusammenfassung zur Seite Nr. 19
Testing the Barcode Scanner (optional) 1. Determine which port the barcode scanner is using: a. In Windows Control Panel, start the Computer Management application b. In Computer Management, select Device Manager. In the Right pane, look under the Ports section, and note the COM value of the USB -Serial Port object. 2. Double-click on the Barcode Scanner Test icon to start the following application: Elo TouchSystems 17A2 User Guide 19
Inhaltszusammenfassung zur Seite Nr. 20
1. Change the port value to match the value you retrieved from the Device Manager. 2. Click Connect. You should see the text Connected in the Messages field. 3. In the box labeled Param Number, enter the value 238. 4. In the box labeled “New Value” enter the value 1. 5. Check the box labeled Permanent Param Change. 6. Scan a barcode. The result should look similar to the following image: Elo TouchSystems 17A2 User Guide 20
