Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Operating Instructions Thank you for purchasing this high-resolution multi-scan color monitor. Please read this guide thoroughly before installation. FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING: (FOR FCC CERTIFIED MODELS) This monitor has been tested and found compliant with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper protection against harmful interference to a residential installation. This monitor
Inhaltszusammenfassung zur Seite Nr. 4
Safety Precautions This monitor is manufactured and tested on the principle that the user’s safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. Warnings: l This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor. If you are unsure of the pow
Inhaltszusammenfassung zur Seite Nr. 5
Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. l Put your monitor in a well-ventilated area. Do not place anything heavy on top of your monitor. l Make certain that your monitor is installed in a clean and moisture-free area. l Keep your monitor away from magnets, motors, transformers, speakers, and TV sets. Safety Tips l If smoke, an abnormal noise or an odor comes out of
Inhaltszusammenfassung zur Seite Nr. 6
CHAPTER 1 Introduction BEFORE INSTALLING YOUR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not recommend by the manufacture Do not attempt to service the monitor your self. If a problem occurs, contact the manufacture's authorized service center ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Displ
Inhaltszusammenfassung zur Seite Nr. 7
FACTORY-PRESET MODES Table 1 shows standard video mode setting that has been pre-adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory-Preset Modes PC mode Mode Resolution H-Freq.(KHz) V-Freq(Hz) NEC 640x400 24.83 56.4 VGA 640x350 31.47 70 720x400 31.47 70 640x480 31.47 60 640x480 37.86 72 640x480 37.5 75 SVGA 800x600 35.16 56.3 800x600 37.88 60.3 800x600 48.08 72.2 800x600 46.87 75 XGA 1024x768 48.36 60 1
Inhaltszusammenfassung zur Seite Nr. 8
Specifications l LCD-1700VR 17” LCD 8U Rack Display Monitor Overall Dimension(HxWxD): 394.5 x 436 x 62 mm Effective Display area(H/V): 337.92 x 270.34 mm Display colors: 16M colors Scan Frequencies: Horizontal 31.47K to 80KHz Vertical 60Hz to 75Hz Number of Pixels: 1280x1024 pixels Pixel pitch: 0.264x0.264 mm Picture Tube: 17" TFT LCD panel Power: Input 110-240VAC(auto-sensing) Frequency: 48-62Hz Consumption 45Watts maximum (on) 3 Watt
Inhaltszusammenfassung zur Seite Nr. 9
Operations: User Controls On/Off Power Button, +/- and Up/down keys On Screen Display Auto adjustment, Brightness, contrast color temperature, Hue, Tint, Source select, PIP setup H-position, V-position, OSD position Audio volume, bass, treble, mute Load default Control Type: Digital Compatibility: IBM and compatible, Apple Macintosh, NEC Environmental Limits: Operating Temp 32° to 103°F ( 0° to 40°C ) Storage Temp. -4° to 140°F ( -20° to 60°C
Inhaltszusammenfassung zur Seite Nr. 10
BNC out BNC In Audio R/L AV1 S video YcbCr Component Audio out DGB In DC power Jack Chapter 2 PRODUCT PACKAGE Open the shipping carton and check the contents. If any items are missing or damaged, contact your dealer immediately. The package should include the following items l Analog Color TFT LCD Monitor l Accessory Box: 1. VGA cable x 1 2. AC to DC adapter x 1 3. Power Cord x 1 4. User’ s manual/Warranty Card x 1 5. Audio cable x 1 6. Mini DIN/RCA cable (for Compon
Inhaltszusammenfassung zur Seite Nr. 11
CONTROL FUNCTIONS The Monitor control functions are located on the lower center of the front view side. They are shown in the figure below and described in the following paragraphs. The control key description 1. : Power Switch 2. - : Decrement 3. : Increment or source select + 4. Ñ : Move to the next item / Brightness control 5. D : Move to the previous item / Brightness control 6. MENU : Activate the on screen display function 12
Inhaltszusammenfassung zur Seite Nr. 12
DESCRIPTION 1. : Power switch Use the power switch to turn ON or OFF power. We recommend turning your system power on first, then the LCD monitor. 2. - & + : decrement or increment the value The two keys are decrement or increment the value or enter into the sub-menu. Note: The + key can change the source directly when de-activation OSD screen. 3. Ñ & D : Select key / Brightness Control keys The two keys have two functions, controlled by the MENU key. When activating OS
Inhaltszusammenfassung zur Seite Nr. 13
CHAPTER 3 1024x768 48.5K 60.2 3 Auto Adjustment - Execute + VER XGA-KDC45-5100 ADJUSTING THE MONITOR VGA OSD main screen 14
Inhaltszusammenfassung zur Seite Nr. 14
1. Each time, when pressing the menu key, the screen will show as above. You can see the 3mark that means the selected item. Then you can change the setting through + or -.key. 2. Pressing Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter into the sub-menu. 3. Then move the Sel key to item you want to change , the item will be highlighted as red characters, then press – or + to change the value. 4. If you finish the
Inhaltszusammenfassung zur Seite Nr. 15
Color balance: 1024x768 60KHz 75Hz the monitor do the white balance Color balance Intensity R Intensity G Intensity B Contrast R Contrast G Contrast B - Execute + VER XGA-KD841-5100 automatically. Intensity R: Adjust the R color intensity, the range is from 0 to 63 Intensity G: Adjust the G color intensity, the range is from 0 to 63 Intensity B: Adjust the B color intensity, the range is from 0 to 63 Contrast R
Inhaltszusammenfassung zur Seite Nr. 16
Geometry setup § We provide Pixel Clock, Phase, H Position, V Position, OSD H Position, OSD V Position and Txt/Gft option to change. § Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99 Phase: Adjust phase tracking to reduce the display flicker. The range is from 0 to 31 § H Position: Move the whole screen horizontally. The range is from 0 to 120. § V Position: Move the whole screen vertically. The range is from 0 to 100. § OSD H Position: Move the OSD horizontal
Inhaltszusammenfassung zur Seite Nr. 17
Note: The PIP function is only valid on video on VGA screen. We can’ t support video on video screen Speaker volume control § We provide Volume, Bass, Treble, Mute and PIP audio for audio setup. § Volume: Adjust the speaker volume. The range is from 0 to 32. § Bass: Adjust the speaker Bass value. The range is from 0 to 10. § Treble: Adjust the speaker Treble value. The range is from 0 to 10. § Mute: Enable or disable the Mute function. § PIP audio: Enable or disable the PIP mute fun
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 4 VIDEO ADJUSTMENT Video OSD Screen NTSC 15.7K 60.2 3 Brightness - Adjustment + 49 VER XGA-KDC45-5100 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3mark, that means the selected item Then you can change the setting through + or -.key. 2. Pressing Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter into the sub-m
Inhaltszusammenfassung zur Seite Nr. 19
§ Adjust the screen contrast value. The range is from 0 to 127 Intensity adjustment § Adjust the screen intensity value. The range is from 0 to 255 Tint adjustment § Adjust the screen Tint value. The range is from 0 to 127 Hue adjustment § Adjust the screen Hue value. The range is from 0 to 255 Geometry setup § We provide Sharpness, H Position, V Position, OSD H Position, and OSD V position. § Sharpness: Adjust the screen sharpness level. The range is from 0 to 15 § H position:
Inhaltszusammenfassung zur Seite Nr. 20
Appendix Troubleshooting Procedures This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. This LCD Monitor Supports Multiple VGA Modes. Refer to the timing table for a listing of factory-preset modes supported by this LCD Monitor. PROBLEM: There is no LCD Display If there is no display on the
