Inhaltszusammenfassung zur Seite Nr. 1
SyncMaster 955MB
Inhaltszusammenfassung zur Seite Nr. 2
Main > Index Main Page On-Screen Display General Highlight Zone Safety Instructions Troubleshooting Notational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Timing Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms Automatic Regulatory Manual Natural Color Base Installation Authority
Inhaltszusammenfassung zur Seite Nr. 3
Main > Safety Instructions > Notational Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Inhaltszusammenfassung zur Seite Nr. 4
Main > Safety Instructions > Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. ? If the size of your monitor is small, or if the same image is present for Notational long periods of time, you may see afterimages due to damage to the Power fluorescent substance on the inside of the CDT. Installation Clean Other Do not use a damaged or loose plug. ? This may cause an electric shock or fire. Do not pull t
Inhaltszusammenfassung zur Seite Nr. 5
Main > Safety Instructions > Installation Do not cover the vents on the monitor cabinet. ? Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Other Put your monitor in a location with low humidity and a minimum of dust. ? An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. ? This may cause damage to the product or human body. Place the monitor on a flat and stable surface. ? The monitor can cause injury
Inhaltszusammenfassung zur Seite Nr. 6
Main > Safety Instructions > Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. Notational (Some detergents contain significant amounts of alcohol-based solvents, Power which can damage (color change) or crack the monitor case. The Installation antiglare/anti-static surface coating on the CDT may also be affected.) Clean Other Dilute the detergent (1:10
Inhaltszusammenfassung zur Seite Nr. 7
Main > Safety Instructions > Other Do not remove cover(or back). No user serviceable parts inside. ? This may cause an electric shock or a fire. ? Refer servicing to qualified service personnel. Notational Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. ? This may cause an electric shock or a fire. Do not place any he
Inhaltszusammenfassung zur Seite Nr. 8
Never insert anything metallic into the monitor openings. ? This may cause an electric shock, fire or injury. Keep the monitor away from any magnetic substances. ? This may cause discoloring or distortion of the image.
Inhaltszusammenfassung zur Seite Nr. 9
Main > Introduction > Unpacking Monitor and Stand Power Cord Unpacking Front Stand Rear Bottom Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD
Inhaltszusammenfassung zur Seite Nr. 10
Main > Introduction > Front Unpacking Front Rear Bottom 1. Highlight button The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit/MagicBright Use this button to exit or conrtol the MagicBright. button 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. Use this button to open the OSD and activate a highlighted menu item. 4. Menu button 5. Power indicator This light
Inhaltszusammenfassung zur Seite Nr. 11
Main > Introduction > Rear Unpacking Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Note: See Connecting Your Monitor for further information regarding cable connections.
Inhaltszusammenfassung zur Seite Nr. 12
Main > Introduction > Bottom Unpacking Front Rear Bottom 1. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
Inhaltszusammenfassung zur Seite Nr. 13
Main > Setup > Connecting Your Monitor Connecting Your Monitor Installing the Monitor Driver Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapt
Inhaltszusammenfassung zur Seite Nr. 14
Main > Setup > Installing the Monitor Driver Connecting Your When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor included with this monitor. Driver installation is slightly different from one operating Installing the system to another. Follow the directions as appropriate for the operating system you Monitor Driver have. Base Installation Prepare a blank disk and download the driver program file at the Internet web site shown here. Inte
Inhaltszusammenfassung zur Seite Nr. 15
4. Click the " " button in the " " window. Install Warning 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Inhaltszusammenfassung zur Seite Nr. 16
Main > Setup > Installing the Monitor Driver Windows XP | Windows 2000 | Windows Me | Windows NT | Linux Connecting Your Monitor Installing the When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor Driver included with this monitor. Driver installation is slightly different from one operating Base Installation system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and downlo
Inhaltszusammenfassung zur Seite Nr. 17
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
Inhaltszusammenfassung zur Seite Nr. 18
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window
Inhaltszusammenfassung zur Seite Nr. 19
4. Select the " " tab. Monitor 5. Click the " " button in the " " area. Change Monitor Type 6. Choose " ". Specify the location of the driver 7. Choose "Display a list of all the driver in a specific location.." then click "Next" button. 8. Click the "Have Disk" button 9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button
Inhaltszusammenfassung zur Seite Nr. 20
Main > Setup > Base Installation Tilt/Swivel Base | Attaching and Removing the Base Connecting Your Monitor Installing the With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable Monitor Driver viewing angle. Base Installation The base is detachable. Note: Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base ont
