Inhaltszusammenfassung zur Seite Nr. 1
Install Drivers Install Programs
SyncMaster 932MP
Inhaltszusammenfassung zur Seite Nr. 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loos
Inhaltszusammenfassung zur Seite Nr. 3
This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which coul
Inhaltszusammenfassung zur Seite Nr. 4
This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or personal injury. Do not place the product on the floor. Someone, specifically children could trip over it. Do not place the product on an unstable or small surface area. Place the product on an even, stable surface, as the product may fall and
Inhaltszusammenfassung zur Seite Nr. 5
Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance. To prevent rainwater from running along the outdoor antenna cable and entering the house
Inhaltszusammenfassung zur Seite Nr. 6
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interio
Inhaltszusammenfassung zur Seite Nr. 7
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or smal
Inhaltszusammenfassung zur Seite Nr. 8
Be careful that adapter should not be in contact with water and therefore not be wet. This may cause malfunction, an electric shock or fire. Do not use adapter by the waterside or outside particularly when it rains or snows. Be careful that adapter should not be wet while cleaning floor with water. Keep all power adapters apart. Failure to do so may cause fire. Keep power adapter away from any other heat source. Failure to do so may cause fire. Remove and discar
Inhaltszusammenfassung zur Seite Nr. 9
to vibrations. Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire. When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and lead to fire or an electric shock.
Inhaltszusammenfassung zur Seite Nr. 10
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor Manual Warranty Card User's Guide, Monitor Driver, Quick Setup Guide (Not available in all locations) Natural Color software Cable
Inhaltszusammenfassung zur Seite Nr. 11
D-Sub Cable Power Cord Radio Antenna Audio Cable DC Adapter Sold separately DVI Cable Others Remote Control Batteries (AAA X 2) Connecter Front 1. MENU 2. AUTO 3. ENTER/FM RADIO 4. SOURCE 5. PIP 6. MagicBright™ 7. CH 8. + VOL - 9. Power button / Power indicator 10. Remote Control Sensor
Inhaltszusammenfassung zur Seite Nr. 12
1. MENU Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 2. AUTO Use this button for auto adjustment. If you change resolution in the control panel, Auto function will be executed. >>Click here to see an animation clip 3. ENTER / FM RADIO ENTER : Activates a highlighted menu item. FM RADIO : In areas where signal is weak, noise may occur while FM radio is broadcast. >>Click here to see an animation clip 4. SOURCE Switches
Inhaltszusammenfassung zur Seite Nr. 13
adjusts the audio volume. >>Click here to see an animation clip 9. Power button / Power indicator Use this button to turn the monitor on and off./ Power Indicator shows PowerSaver mode by green blinking. 10. Remote Control Sensor Aim the remote control towards this spot on the Monitor. See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended
Inhaltszusammenfassung zur Seite Nr. 14
3. COMPONENT IN COMPONENT IN ( R-AUDIO-L / PR / PB / Y ) : DVD/DTV left / right audio connection terminal (R/L) DVD/DTV Component(PR, PB,Y) terminal 4. FM ANT / ANT IN FM ANT / ANT IN : FM RADIO ANT connection terminal TV connection terminal For more information > Connecting TV 5. EXT(RGB) EXT(RGB) : EXT(RGB) connection terminal - Scart is mainly used in Europe. 6. S-VIDEO / VIDEO / L-AUDIO-R / S-VIDEO / VIDEO / L-AUDIO-R / : S-Video co
Inhaltszusammenfassung zur Seite Nr. 15
Remote Control The performance of the remote control may be affected by a TV or other electronic device operated near the monitor, causing malfunction due to interference with frequency. 1. POWER 2. Number button 3. +100, -/-- 4.- + 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. FM RADIO 10. CH/P 11. SOURCE 12. INFO 13. EXIT 14. Up-Down Left-Right Buttons 15. AUTO 16. P.MODE, M/B (MagicBright™) 17. P.SIZE 18. STILL 19. PIP 20. S.MODE 21. DUAL/MTS 22. PRE-CH 2
Inhaltszusammenfassung zur Seite Nr. 16
1. POWER Use this button to turn the monitor on and off. 2. Number button Selects TV channels in the TV mode. You may use this button in PIP mode as well. 3. +100 Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1". -/-- (One/Two-Digit channel selection ) Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number. -/-- is mainly used in Europ
Inhaltszusammenfassung zur Seite Nr. 17
17. P.SIZE - Not available in PC/DVI Mode Press to change the screen size. Zoom1, Zoom2 are not available in 1080i(or over 720p) of DTV. 18. STILL Press the button once to freeze the screen. Press it again to unfreeze. 19. PIP Push the PIP button to turn PIP screen On/Off. 20. S.MODE ( Sound Mode ) When you press this button, current mode is displayed on the lower center of the screen. The Monitor has a built-in high fidelity stereo amplifier. Then push button again to
Inhaltszusammenfassung zur Seite Nr. 18
Connecting the monitor 1. Connecting to a Computer 1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER port on the monitor. (Voltage is automatically adjusted by the power adapter.). 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back
Inhaltszusammenfassung zur Seite Nr. 19
If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source. 2. Connecting to a Macintosh 1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER port on the monitor. (Voltage is automatically adjusted by the power adapter.) 2. Using the D-sub (Analog) connector on the video card. C
Inhaltszusammenfassung zur Seite Nr. 20
1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the monitor using the RCA or S-Video cable. S-Video, RCA cable and EXT(RGB) cable is optional. 2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 3. Select AV or S-Video using the SOURCE button on the monitor's front. 4. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio c
