Inhaltszusammenfassung zur Seite Nr. 1
TP-6000 SERIES
USER’S MANUAL
TOUCH PANEL POS SYSTEM
Rev. : Original
Inhaltszusammenfassung zur Seite Nr. 2
SOME IMPORTANT NOTES FCC NOTES This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS BRIEF INTRODUCTION..................................1-1 THE USER’S MANUAL ................................1-1 THE PRODUCT.......................................1-1 Overview .......................................1-1 Configuration ....................................1-1 Available Models..............................1-1 Standard Features..............................1-2 Optional Items................................1-3 SYSTEM BOX CONTENTS...............................2-1 MAIN UN
Inhaltszusammenfassung zur Seite Nr. 4
PREPARING THE MAIN UNIT ..........................4-4 JOINING MAIN UNIT AND PADDLE .....................4-4 OPENING CABLE COVER .............................4-5 CONNECTING CABLES ...............................4-6 INSTALLING CASH DRAWERS ........................4-6 WALL MOUNTING ....................................4-7 LOCATION FOR INSTALLATION .......................4-7 USING THE TOUCH POS ................................5-1 APPLICATION ENVIRONMENT .........................5-1 Ventilation ......
Inhaltszusammenfassung zur Seite Nr. 5
BRIEF INTRODUCTION THE USER’S MANUAL The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex fully integrated compact touch terminal system with touch panel input. TP6000 series is a product group of fully integrated PC based touch terminal systems. However, this manual does not intend to explain any application program that may be supplied with the TP6000 systems. The user should consult the software supplier or the VAR that he purchased from
Inhaltszusammenfassung zur Seite Nr. 6
STANDARD FEATURES a) CPU: Celeron 366MHz up to 500 MHz HDD: 6.4 GB or above b) Support MS DOS, WIN98, WIN NT, WIN 2000 environment (WIN 2000 support starting June 2000) c) Power saving support: doze or suspension mode d) High quality 12.1” / 15.1” TFT active matrix LCD panel e) Vertical type LCD panel with easy tilt angle adjustment from 18° to 87° f) Height adjustment: the high / low adjustment gives 20 mm difference in height g) Resistor type touch panel h) Extra long life touch panel that end
Inhaltszusammenfassung zur Seite Nr. 7
o) Built-in UPS function to support the system from intermittent power failure (battery itself is an option) p) Accidental power off protection – The power switch is safely located at one side, and this power switch can be defined as a “ON” switch only through software command q) Forced power off against system malfunction under the power switch on/off mode r) Touch control functions: left/right button, double click, drag & draw s) Touch sound can be enabled/disabled or pitch adjusted by softwar
Inhaltszusammenfassung zur Seite Nr. 8
TP6000 USER’S MANUAL 1 - 4
Inhaltszusammenfassung zur Seite Nr. 9
SYSTEM BOX CONTENTS MAIN UNIT & PADDLE ASSEMBLY Open the carton User’s Carton Manual Packaging Packaging materials materials Power Documents for Supply Preloaded OS Unit Power Cord Bottom of TP6000 System and take all the contents out together with the packaging materials. Take out the accessories/options from the partitions in the packaging materials and unfold the packaging materials carefully to unload the upsidedown loaded TP6000 series touch terminal. Put this main unit & paddle assembly as
Inhaltszusammenfassung zur Seite Nr. 10
The COM1 terminator will be already mounted on the system unit when being shipped. The latch key for cable cover lock will be in a bag. OPTIONAL DEVICES There are several options that will be mounted on/in the main system unit either by the manufacturer if ordered. These optional devices include: • DRAM expansion – This option includes any possibility from basic 32 MB to maximum 1 GB. • Built in card reader – This option will be on the right edge when installed. Selectable from two tracks (track
Inhaltszusammenfassung zur Seite Nr. 11
PARTS IDENTIFICATION FRONT VIEW MSR Unit Display Screen + Touch Panel Main Unit Adjustable Paddle Assembly The MSR unit is option to both 12” and 15” models. The LED in the logo area serves for multiple purposes through giving different indication of steady/flashing green/orange light. Please refer to the paragraph discussing the LED indication in the chapter of “USING THE TOUCH POS” of this manual. TP6000 USER’S MANUAL 3 - 1
Inhaltszusammenfassung zur Seite Nr. 12
SIDE VIEWS Right Side View Latch Hole For Cable Cover Push In This Direction To Adjust The Tilt Angle Of The Display Panel Lock/Release Lever Left Side View Push Down To Switch The Power ON/OFF Latch Hole For Cable Cover Slide Switch For Power On/Off Control TP6000 USER’S MANUAL 3 - 2
Inhaltszusammenfassung zur Seite Nr. 13
REAR VIEW Lock/Release Button To Detach The Main Unit Optional MSR Unit Lock/Release Lever Cable Exit REAR VIEW OF MAIN UNIT Service Window Matching Pegs Cable Exit Cable Cover Removal Hollow Of Cable Cover TP6000 USER’S MANUAL 3 - 3
Inhaltszusammenfassung zur Seite Nr. 14
ADJUSTABLE PADDLE ASSEMBLY Matching Holes Paddle Base Lock/Release Lever BOTTOM OF PADDLE ASSEMBLY Base UPS Battery Cable Passage Cover Cover Lock/Release Cable Exit Button For Main Unit Paddle CONNECTORS Turn Counterclockwise Then Take Out The Latch Key Pull The Cable Cover Out In This Direction TP6000 USER’S MANUAL 3 - 4
Inhaltszusammenfassung zur Seite Nr. 15
USB5 Port PS/2 KB USB4 Port COM1 Port PS/2 Mouse USB3 Port COM2 Port Cash Drawer Controller USB2 Port External VGA Port Power Input Jack USB1 Port LPT1 Printer Port LAN Port UPS Battery Connector External FDD Port MSR Port LED Connector TP6000 USER’S MANUAL 3 - 5
Inhaltszusammenfassung zur Seite Nr. 16
TP6000 USER’S MANUAL 3 - 6
Inhaltszusammenfassung zur Seite Nr. 17
INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded. SEPARATING MAIN UNIT Press the Lock/Release button and lift the main unit to detach it from the paddle assembly. In order
Inhaltszusammenfassung zur Seite Nr. 18
PREPARING PADDLE ASSEMBLY Take the adjustable paddle assembly and turn it up side down to show the bottom of the base. 2 Sets of 4 Matching Holes Screws Cable Passage Adjustable Cover Paddle Now, unscrew the 2 screws on the cable passage cover and take the cable Lock/Release passage cover away to show the cable Lever passage. If there is no need to install the optional UPS battery here (either not to be installed or already installed), please skip the next paragraph and directly start routing ca
Inhaltszusammenfassung zur Seite Nr. 19
INSTALLING UPS BATTERY UPS Battery Removed Battery Cover Place the optional UPS battery in the battery compartment in the way as indicated in the picture. Screw on the battery cover and join the battery cable into the cable routing operation. Please enable UPS function in software setting before use. ROUTING THE CABLES Place all the cables required for connections to the TP6000 series except those for special application purposes into the cable passage. Inset one end of the cable passage cover u
Inhaltszusammenfassung zur Seite Nr. 20
PREPARING THE MAIN UNIT On the back of the main unit, there are 4 matching pegs and a service window. Push open the service window in the direction as indicated in the picture, one can find a button cell battery socket, a 1 x 3 header (JP10) with 1 jumper and a 2 x 3 header (JP8) with 2 jumpers. Service 4 Matching Window Pegs Push Open To The Right This battery socket accepts a 3 V button cell Lithium battery (CR2032) required to support the system real time clock. The jumpers in this window are