Inhaltszusammenfassung zur Seite Nr. 1
BDL4230E
www.philips.com/welcome
EN User manual
Cleaning and troubleshooting
Inhaltszusammenfassung zur Seite Nr. 2
User Manual BDL4230E SAFETY AND TROUBLESHOOTING INFORMATION Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your monitor: Operation: • Keep the monitor out of direct sunlight and away from stoves or any other heat source. • Remove any object that could fall into ventila
Inhaltszusammenfassung zur Seite Nr. 3
User Manual BDL4230E Service: • The casing cover should be opened only by qualified service personnel. • If there is any need for any document for repair or integration, please contact with your local service center. • Do not leave your monitor in a car/trunk under direct sun light. Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed. Read and follow these instru
Inhaltszusammenfassung zur Seite Nr. 4
User Manual BDL4230E REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declares under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • EN
Inhaltszusammenfassung zur Seite Nr. 5
User Manual BDL4230E POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely sw
Inhaltszusammenfassung zur Seite Nr. 6
User Manual BDL4230E INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains p
Inhaltszusammenfassung zur Seite Nr. 7
User Manual BDL4230E ( RoHS + (Hg) (Cd) (PBB) (PBDE) (Pb) (Cr 6 ) OOO O O O XX O O O O XO O O O O XO O O O O ( ) XO O O O O O SJ/T11363-2006 X SJ/T11363-2006 ( )
Inhaltszusammenfassung zur Seite Nr. 8
User Manual BDL4230E NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ
Inhaltszusammenfassung zur Seite Nr. 9
User Manual BDL4230E TABLE OF CONTENTS 1. UNPACKING AND INSTALLATION 1.1. UNPACKING 1.2. PACKAGE CONTENTS 1.3. INSTALLATION NOTES 1.4. PORTRAIT MOUNTING 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 2.2. REAR VIEW 2.3. INPUT/OUTPUT TERMINALS 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 2.4.3. OPERATING RANGE OF THE REMOTE CONTROL 3. CONNECTIONS TO EXTERNAL EQUIPMENT 3
Inhaltszusammenfassung zur Seite Nr. 10
User Manual BDL4230E 6.2. TYPES OF PIXEL DEFECTS + DOT DEFINITION 6.3. BRIGHT DOT DEFECTS 6.4. DARK DOT DEFECTS 6.5. PROXIMITY OF PIXEL DEFECTS 6.6. PIXEL DEFECT TOLERANCES 7. CLEANING AND TROUBLESHOOTING 7.1. CLEANING 7.2. TROUBLESHOOTING 8. TECHNICAL SPECIFICATIONS
Inhaltszusammenfassung zur Seite Nr. 11
User Manual BDL4230E 1. UNPACKING AND INSTALLATION 1.1. UNPACKING • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • The weight of the product differs - depending on the type. Due to the size and weight it is recommended to move it by 2 people. • The protective glass and the glass substrate are installed on the front of the product. Since both glass can be broken and scraped easily, the product has t
Inhaltszusammenfassung zur Seite Nr. 12
User Manual BDL4230E 1.4. PORTRAIT MOUNTING Wall mounting holes Notes: Note: The remote control sensor should be on the lower side when rotating your monitor. • Metric 6 (10mm) screws are needed for wall mounting (not included). • The mounting interface should comply with the UL1678 standard in North America. The mounting means should strong enough to bear the weight of the monitor (approx. 24.5kg without stand). How to use the logo guider? Allowable tilting angle in Portrait Mode How to
Inhaltszusammenfassung zur Seite Nr. 13
User Manual BDL4230E 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 1 1. Remote control sensor, ambient light sensor and power indicator • Receives command signals from the remote control. • Detects the ambient lighting condition around the monitor. • Indicates the operating status of the monitor: - lights blue when the monitor is turned on - lights amber when the monitor is in standby mode - blinks blue when remote control signal is received - blinks amber when the monitor enters DPMS mode - off
Inhaltszusammenfassung zur Seite Nr. 14
100 mm 100 mm User Manual BDL4230E 2.2. REAR VIEW 100 mm 9 Dent depth: 6mm 35 mm 8 200 mm 7 210.4 mm 1 2 3 4 5 6 1. ENTER/VIDEO SOURCE button • Use this button to select the input source. • When the On Screen Display menu is active, use this as the SET button. 2. MENU button • Use this button to engage the On Screen Display menu. • When the On Screen Display menu is active, use this button to return to the previous menu. 3. / button • When the On Screen Display menu is active, use these as
Inhaltszusammenfassung zur Seite Nr. 15
User Manual BDL4230E 2.3. INPUT/OUTPUT TERMINALS 7 12 1 2 3 4 5 6 8 9 10 11 13 14 15 16 1. AUDIO IN (AUDIO1) 9. RS232C (OUT/IN) RS232C network connection input/output for the use of Connect to the audio output of a computer. loop through function. 2. AUDIO OUT R/L 10. VIDEO IN (COMPONENT) Outputs the audio signal from the AUDIO IN Component video input (YPbPr) for connecting to the (AUDIO1/AUDIO2/AUDIO3)or HDMI jack. component output of an AV device. 3. SPEAKERS R/L 11. VIDEO IN (S-VIDEO) O
Inhaltszusammenfassung zur Seite Nr. 16
User Manual BDL4230E 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS POWER button Press to switch on the monitor from standby mode. Press again to turn it off to standby mode. SMART button To select smart picture mode from: • HIGHBRIGHT: for moving image such as Video • STANDARD: for images (factory setting) • sRGB: for text based images • CINEMA: for movies. • CUSTOM: use your own picture setting. The mode is automatically selected after you change the settings in the PICTURE menu. VIDEO S
Inhaltszusammenfassung zur Seite Nr. 17
User Manual BDL4230E DISPLAY button To turn on/off the setting information displayed on the upper right corner of the screen. MENU button To turn the OSD menu on/off. UP button • To move the highlight bar up to adjust the selected item when OSD menu is on. • To move the sub-picture up in “PIP” mode. DOWN button • To move the highlight bar down to adjust the selected item when OSD menu is on. • To move the sub-picture down in “PIP” mode. PLUS button • To increase the adjustment with OSD menu. •
Inhaltszusammenfassung zur Seite Nr. 18
User Manual BDL4230E 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 1. Remove the cover on the rear of the remote control. 2. Insert two AAA size 1.5V batteries ensuring that the “+” and “-” ends of the batteries are correctly aligned. 3. Replace the cover. Note: Do not mix battery types, e.g. alkaline and manganese. 2.4.3. OPERATING RANGE OF THE REMOTE CONTROL Point the top of the remote control toward the monitor's remote control sensor when pressing a button. Use the remote con
Inhaltszusammenfassung zur Seite Nr. 19
User Manual BDL4230E 3. CONNECTIONS TO EXTERNAL EQUIPMENT 3.1. USING THE CABLE RETAINER 3.2. USING THE SWITCH COVER You can use the switch cover to prevent the monitor from being turned on or off accidentally. 3.3. CONNECTING EXTERNAL EQUIPMENT (DVD/VCR/VCD) 3.3.1. USING COMPONENT VIDEO INPUT 1. Connect the green-colored (labeled as "Y") jack of the device to the green-colored "Y" jack of the monitor. 2. Connect the blue-colored (labeled as "Pb") jack of the device to the blue-col
Inhaltszusammenfassung zur Seite Nr. 20
User Manual BDL4230E 3.3.2. USING S-VIDEO INPUT 1. Connect the S-Video connector of the external device to the S-VIDEO input of the monitor. 2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the monitor. DVD/VCR/VCD 3.3.3. USING VIDEO INPUT 1. Connect the Video connector of the external device to the VIDEO IN input of the monitor. Use the supplied BNC-to- RCA adapter if necessary. 2. Connect the red (R) and white (L) audio jacks of
