Inhaltszusammenfassung zur Seite Nr. 1
Liquid Crystal Video Monitor
BT-LS1400P
POWER MENU/
INPUT SCAN BLUE EXIT ENTER
MENU VOLUME
Before attempting to connect, operate or adjust this product, please read these instructions completely.
Printed in Japan
VQT0F29
Inhaltszusammenfassung zur Seite Nr. 2
For your safety FCC Note: CAUTION This device complies with Part 15 of the FCC Rules. RISK OF ELECTRIC SHOCK To assure continued compliance follow the attached DO NOT OPEN installation instructions and do not make any unautho- rized modifications. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). This equipment has been tested and found to comply NO USER SERVICEABLE PARTS INSIDE. with the limits for a class A digital device, pursuant to REFER TO SERVICING TO QUALIFI
Inhaltszusammenfassung zur Seite Nr. 3
For your safety ∫ THIS APPARATUS MUST BE GROUNDED CAUTION: To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power outlet THIS APPARATUS CAN BE OPERATED AT A which is effectively grounded through normal house- VOLTAGE OF 120 V OR ON THE RANGE OF hold wiring. 220 – 240 V AC. OPERATION AT A VOLTAGE Extension cords used with the equipment must be IN THE RANGE OF 220 – 240 V AC IS NOT three-core and be correctly wired to provide connec- INTENDED FOR U.S.A.
Inhaltszusammenfassung zur Seite Nr. 4
Precautions for use This product has been specially designed for commercial use. As such, it should be used and operated only by persons with related expertise. ¥ ¥ The liquid crystal parts are fabricated using high-precision technology. The screen has effective pixels that cover more than 99.99% of its area, but pixels may be missing or remain permanently lighted (red, blue and/or green) in less than 0.01% of the area. This is not indicative of malfunctioning. ¥ ¥ The LCD panel has been spec
Inhaltszusammenfassung zur Seite Nr. 5
Introduction The BT-LS1400 commercial-use LCD video monitor features a 14 v-type LCD screen, a slim and lightweight design, and a wide angle of view. Its connectors support not only standard NTSC signal input but S-Video, 480i , P component signal input and SD SDI (optional) input as well. ∫ Wide angle of view ∫ Functions By using an LCD screen with a wide angle of view, This monitor is equipped with a blue-only function for exceptional image visibility is assured across wide angle adjusting th
Inhaltszusammenfassung zur Seite Nr. 6
Parts and their functions (rear panel) = > ? @ LINE A VIDEO IN AUDIO OUT S-VIDEO 9 IN OUT IN OUTRLR L IN AUDIO OUT LINE B VIDEO S-VIDEO : IN OUT IN OUTRLR L CMPNT REMOTE COMPONENT AUDIO IN IN Y P P B R RL ;< 9 ? LINE-A Security lock These connectors are for composite signal and S-video This can be used to connect a commercially-available signal and audio signal input. Priority is given to the S- theft-prevention cable (manufactured by Kensington). video signal for input. This security lock is c
Inhaltszusammenfassung zur Seite Nr. 7
How to use the on-screen menus Press the MENU/EXIT button to display the main menu on the screen. MENU/EXIT button ª Menus The following items appear on the main menu. 1 PICTURE [MAIN MENU] 1 PICTURE 4 This menu is used to perform the settings relating to the VIDEO CONFIG 4 SYSTEM CONFIG 4 picture. 2 MAINTENANCE 4 [INPUT] 3 2 VIDEO CONFIG LINE A This menu is used to perform aspect and component 4 input level settings. 5 3 SYSTEM CONFIG This menu is used to set the backlight brightne
Inhaltszusammenfassung zur Seite Nr. 8
How to use the on-screen menus ¥ PICTURE menu The menu items shown below appear when the PICTURE menu is selected on the main menu. PHASE [PICTURE MENU] MODE BROADCAST The phase can be adjusted here. CONTRAST 60 Use the blue-only function to adjust the level while viewing BRIGHT 30 CHROMA 30 the SMPTE color bars. PHASE 30 SHARPNESS 30 AI OFF SHARPNESS NR OFF COLOR TEMP D
Inhaltszusammenfassung zur Seite Nr. 9
How to use the on-screen menus ¥ VIDEO CONFIG menu The menu items shown below appear when the VIDEO CONFIG menu is selected on the main menu. ASPECT [VIDEO CONFIG] ASPECT 16:9 An aspect ratio of 4:3 or 16:9 can be set. COMPONENT LEVEL SMPTE The underscanning function cannot be used when 16:9 has been selected. COMPONENT LEVEL The component input level is selected here. This menu item appears only when the component signal has been selected as the input signal. ≥ SMPTE Select this w
Inhaltszusammenfassung zur Seite Nr. 10
How to use the on-screen menus ¥ MAINTENANCE menu The menu item shown below appears when the MAINTENANCE menu is selected on the main menu. RUNNING TIME [MAINTENANCE] The total running time of the monitor is displayed here (in RUNNING TIME 300H hours). REMOTE specifications In order to perform REMOTE operations, select ON as the setting for the REMOTE menu item on the SYSTEM CONFIG menu. The functions for REMOTE operations can be switched by 5 4 3 2 1 Connector (9P) opening or shorting the
Inhaltszusammenfassung zur Seite Nr. 11
About the stand The stand attached to the unit can be tilted forward 10° and back 20°. When tilting the monitor, firmly press down on the stand and grasp the top part of the monitor. Further, it is recommended to secure the stand using the screw holes when it is to be permanently located. Take care not to catch your fingers or hands when tilting the stand. Rack mounting The unit can be mounted into a 19-inch standard rack (height: 7U size) if the optional rack-mounting adaptors (BT-MA1400
Inhaltszusammenfassung zur Seite Nr. 12
Maintenance ≥ ≥ Wipe off any dust or dirt on the monitor and LCD panel with a soft cloth. For stubborn dirt or stains, wipe the monitor and LCD panel with a cloth that has been lightly dampened with well-diluted kitchen detergent and wrung out thoroughly, then finish it off with a dry cloth. The monitor may malfunction if even one drop of water gets into the internals. ≥ ≥ Do not spray detergent or other cleaners directly on the monitor or LCD panel. The monitor may malfunction if even one drop
Inhaltszusammenfassung zur Seite Nr. 13
Specifications [GENERAL] [Video signal output] LINE A: Loop-through output, 75 h automatic termination Power supply: AC 100 V to 240 V, 50-60 Hz (BNC, S connector) Power consumption: 0.98 A to 0.54 A LINE B: indicates safety information. Loop-through output, 75 h automatic termination (BNC, S connector) Dimensions (Wa aHa aD): SDI (optional): 14 a 12-1/8 a 2-13/16 inch (main unit only) Buffer output (BNC, 480/59.94i) (356 a 308.5 a 71.5 mm) 14 a 13-3/8 a 7-3/8 inch (with monitor stand) (356 a 34
Inhaltszusammenfassung zur Seite Nr. 14
Memo 14
Inhaltszusammenfassung zur Seite Nr. 15
Memo 15
Inhaltszusammenfassung zur Seite Nr. 16
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3
