Inhaltszusammenfassung zur Seite Nr. 1
User’s Manual
MultiSync X461S
MultiSync X551S
Inhaltszusammenfassung zur Seite Nr. 2
Index Declaration of conformity .............................................................................................................................. English-1 Important Information ................................................................................................................................... English-2 WARNING ....................................................................................................................................... English-2 CAUTION .....
Inhaltszusammenfassung zur Seite Nr. 3
Declaration of conformity For USA FCC Information 1. Use the attached specifi ed cables with the MultiSync X461S (L460TZ)/MultiSync X551S (L550TH) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use a good quality shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found t
Inhaltszusammenfassung zur Seite Nr. 4
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAG
Inhaltszusammenfassung zur Seite Nr. 5
Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE Immediately unplug your monitor from the wall outlet and refer FOLLOWING WHEN SETTING UP AND USING servicing to qualifi ed service personnel under the following THE MULTI-FUNCTION MONITOR: conditions: � DO NOT OPEN THE MONITOR. There are no user � When the power supply cord or plug is damaged. serviceable parts inside and opening or removing covers may � If liquid has been spilled, or objects have fallen
Inhaltszusammenfassung zur Seite Nr. 6
Contents Your new MultiSync monitor box* should contain the following: � LCD monitor � Screw for Option board slot (M4 x 6) x 2 1 � Power cord* � CD-ROM � Video Signal Cable � Option board slot cover � Wireless Remote Control and AA Batteries � Wall Mount adapter x 4 � Setup Manual � Wall Mount adapter screw x 4 � Clamp x 3 � Thumbscrew for optional stand x 2 � Screw with washer (M4 x 10) x 5 Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Screw with washer Wall mount adapter Thum
Inhaltszusammenfassung zur Seite Nr. 7
Installation This device cannot be used or installed without the Tabletop Using an optional wall mount (WM-46S-L/WM-46S-P) Stand or other mounting accessory for support. For proper � When using an optional wall mount (WM-46S-L/WM- installation it is strongly recommended to use a trained, 46S-P) or there is not enough room in back side, the NEC authorized service person. Failure to follow NEC handles may need to be changed from normal to thin standard mounting procedures could result in dama
Inhaltszusammenfassung zur Seite Nr. 8
Mounting location Attaching Mounting Accessories � The ceiling and wall must be strong enough to support the The monitor is designed for use with the VESA mounting monitor and mounting accessories. system. � DO NOT install in locations where a door or gate can hit the unit. 1. Attach Mounting Accessories � DO NOT install in areas where the unit will be subjected Be careful to avoid tipping monitor when attaching to strong vibrations and dust. accessories. � DO NOT install near where the ma
Inhaltszusammenfassung zur Seite Nr. 9
NOTE: Install the stand so the long end of the feet face 3. Using Wall Mount Adapter forward. Use the ST-4020 for the X461S and the If the mounting accessory interferes with the option board, ST5220 for the X551S. ventilation hold or speaker attachment hole, use the included wall mount adaptors and screws. If the adaptor screws are 5. Ventilation Requirements too long, include a washer to reduce the depth. Washer not included. When mounting in an enclosed space or recessed area, leave ad
Inhaltszusammenfassung zur Seite Nr. 10
Parts Name and Functions Control Panel POWER button EXIT button Switches the power on/off. See also page 16. Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous MUTE button menu. Switches the audio mute ON/OFF. Remote control sensor and Power Indicator INPUT button Receives the signal from the remote control (when using the wireless remote control). See also page 11. Acts as SET button within OSD menu. (Toggle switches Glows
Inhaltszusammenfassung zur Seite Nr. 11
Terminal Panel AC IN connector RS-232C (D-Sub 9 pin) Connects with the supplied power cord. IN connector: Connect RS-232C input from external equipment such as a PC in order to control RS-232C Main Power Switch functions. OUT connector: Connect RS-232C output. To connect On/Off switch to turn main power ON/OFF. multiple MultiSync monitors via RS-232C daisy Chain. DISPLAYPORT connector AUDIO OUT To input DisplayPort signals. To output the audio signal from the AUDIO IN 1, DPORT and
Inhaltszusammenfassung zur Seite Nr. 12
Wireless Remote Control ASPECT button Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1], [ZOOM] and [NORMAL]. See page 17. SOUND button Artifi cial surround sound for internal/external speakers. Audio out is disabled when surround is set to ON. KEYPAD Press buttons to set and change passwords, change channel and set REMOTE ID. 2 ENT button* DISPLAY button Turns on/off the information OSD. See page 18. MENU button Turns on/off the menu mode. AUTO SETUP button Enters auto set
Inhaltszusammenfassung zur Seite Nr. 13
PIP (Picture In Picture) button Operating Range for the Remote ON/OFF button: Toggle switches between PIP, POP, Control PICTURE BY PICTURE-ASPECT and PICTURE BY Point the top of the remote control toward the LCD monitor’s PICTURE-FULL. See page 22. remote sensor during button operation. INPUT button: Selects the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub Use the remote control within a distance of about 7 m (23 ft.) picture. from remote control
Inhaltszusammenfassung zur Seite Nr. 14
Setup NEC recommends the following battery use: 1. Determine the installation location � Place “AA” size batteries matching the (+) and (-) signs CAUTION: Installing your LCD monitor must be done by a on each battery to the (+) and (-) signs of the battery qualifi ed technician. Contact your dealer for more compartment. information. � Do not mix battery brands. CAUTION: MOVING OR INSTALLING THE LCD MONITOR � Do not combine new and old batteries. This can shorten MUST BE DONE BY TWO OR MORE
Inhaltszusammenfassung zur Seite Nr. 15
5. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer fi rst. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required. 8. Adjust the screen (See pages 20 and 21) Make adjustments of the screen display position when necessary. 9. Adjust the image (See page 20) Make adjustments such as backlight or contrast when required. 10.
Inhaltszusammenfassung zur Seite Nr. 16
Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Wiring Diagram Solid lines = video sig
Inhaltszusammenfassung zur Seite Nr. 17
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. Scanning frequency Remarks Resolution Horizontal Vertical 640 x 480 31.5 kHz 60 Hz 800 x 600 37.9 kHz 60 Hz 1024 x 768 48.4 kHz 60 Hz 1280 x 768
Inhaltszusammenfassung zur Seite Nr. 18
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD. OFF Main Power Switch ON Power Button Using the remote control English-16
Inhaltszusammenfassung zur Seite Nr. 19
Power Indicator Picture Aspect DVI, VGA, DPORT Mode Status Indicator Light FULL 1:1 ZOOM NORMAL 1 Power ON Green* Power OFF Red HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO Power consumption under 0.5 W Power Save Amber FULL WIDE DYNAMIC 1:1 ZOOM NORMAL 2 Power consumption under 1 W* Power Standby when “SCHEDULE Green and Amber blink alternately SETTINGS” enabled Aspect ratio Recommended selection 3 Unchanged view* 3 of image for picture aspect* Diagnosis (Detecting failure) Red
Inhaltszusammenfassung zur Seite Nr. 20
Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. 1 ID number assigned to current monitor* 2 ID number assigned monitor to be controlled via RS-232C* Input Name Audio input mode Picture aspect Input Signal Information Sub picture information *1: “IR CONTROL” should be set “Primary” or “Secondary”. *2: “IR CONTROL” should be set “Primary”. Pict
