Inhaltszusammenfassung zur Seite Nr. 1
LM-3000
USER’S MANUAL
LCD MONITOR
Inhaltszusammenfassung zur Seite Nr. 2
FCC NOTICE This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is
Inhaltszusammenfassung zur Seite Nr. 3
I. LM-3000 is a highly luminant with low shadow effect 12.1” LCD monitor. It is economical of pace and provides broad display area II. • • VGA ADAPTOR CARD – PST032 • • III. The LM-3000 LCD panel is delivered with a separate base. The user has to find a surface which is horizontal and flat enough to place the LCD panel with its supporting base on. Please always manage to keep the installation site away from possibility of falling, shock, vibration, direct sun light, heavy dust, high temper
Inhaltszusammenfassung zur Seite Nr. 4
IV. J2 J1 The attached PST032 is a PCI bus SVGA adaptor card which offers a 50 pin SCSI type connector for LM-3000 ( Do not connect any device other than the LM-3000 LCD monitor to this port even if it was using a SCSI connector! ) and a 3 x 5 D sub connector for external SVGA monitor. The user shall always first turn off the power to the PC and all its connected peripherals and disconnect all cables connected to the PC and then open the case of PC according to relevant instructions. The origin
Inhaltszusammenfassung zur Seite Nr. 5
V. The cable length is 1.5 M, that allows the user to arrange the LM- 3000 at any place within this range from the PC. At one end of the cable attached is a SCSI 50 pin connector, at the other end, the connections are already installed to the rear of the LCD panel. Route the cables via the rear part of the base and clip them to the grooves to ensure that no excess strain passes to the cable connection to the panel. The user shall first press the two springs of the 50 pin SCSI type connector the
Inhaltszusammenfassung zur Seite Nr. 6
VI. A. For Windows 3.1 The drivers for Windows 3.1 are delivered in a separate 3.5” floppy diskette with the LCD monitor. To install the drivers for Windows 3.1 with the LCD monitor, the user should make sure that 1. 2. 3. 4. Type in “A:\SETUP” with the diskette containing drivers Windows 3.1 inserted in FDD A: (if it is in B: drive, type in 5. 6. Press any key when being asked of confirmation to start installation. 7. Press “ENTER” twice and then press the “END” key to input 8. Replace th
Inhaltszusammenfassung zur Seite Nr. 7
start with CHIPS followed by either the number 65550 or 17. B. For Windows 95 The following describes normal display driver installation procedures for Windows 95. Use these procedures when installing the display drivers provided in the directory for Windows 95. The Select the page of "Settings", and click the "Change Display Type" button. Example 1: Insert the drivers disk in the A: floppy drive, and enter Example 2: Type in the name of the directory where you copied the drivers, either on yo
Inhaltszusammenfassung zur Seite Nr. 8
C. For Windows NT 3.5x The drivers for Windows NT of versions 3.5x are stored in a 1. Run Windows NT Setup from Main Group 2. Choose O C O D. For Windows NT 4.0 The drivers for Windows NT of versions 4.0 are stored in a Step 1: Install Windows NT as you normally would for a VGA First click the Start button , go to Settings and click on Control Panel. Choose the Display icon and click on the icon. In the Display Properties window, click on the Settings tab. Then click on Change Display Type. In
Inhaltszusammenfassung zur Seite Nr. 9
Step 3: Upon restart, select the desired display settings from the Display property dialog box. Click on Test to test the newly selected graphics mode. A color test screen should appear, followed by the Testing Mode window. Click on Yes to continue. The Display Settings Change window will appear. Click on Restart Now for the VII. • slide : without • Swivel : ° • Tilt : position, total ° . • Brightness : picture displayed. The left one (as viewed from “ ” brightness of the picture, and
Inhaltszusammenfassung zur Seite Nr. 10
Tilt Contrast Swivel 8 LM-3000 USER’S MANUAL - page control knob Brightness control knob
Inhaltszusammenfassung zur Seite Nr. 11
VIII. SVGA 800 x 600 247.02 (W) x 185 250 ms Backlight: 0.0821 (W) x 0 0.2021 (W) x 0 2 Brightness: 150 cd/m 0 °C ~ 40 °C °C ~ 60 °C for Temp ≤ 40 °C, 10% ~ 85%RH, non- for Temp > 40 °C, Absolute humidity °C Back Light Reliability: PST032 Control Card Bus Type: Display Mode Supported: Cable Length: 1.5m CONTRAST Swivel Range: ° ° ° ° Slide Range: Total Width: 300 mm 188 mm 251 mm 9 LM-3000 USER’S MANUAL - page Total Height: Total Depth: Left 36 mm and right 36 mm ) to backward 85 Stand straight
Inhaltszusammenfassung zur Seite Nr. 12
The manufacturer of the LCD display system makes no representations or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect, special or consequential damages. Information in this document is subject to change without notice and does not represent a commitment on behalf of the manufacturer. 10 LM-3000 USER’S MANUAL - page DISCLAIMER
