Inhaltszusammenfassung zur Seite Nr. 1
AUTO-SCANNING WITH DIGITAL CONTROL
COLOUR DISPLAY MONITOR
MODEL : M557
M700
USER’S MANUAL
BEDIENERHANDBUCH
MANUAL DEL USUARIO
MANUEL UTILISATEUR
MANUALE UTENTE
For future reference, record the serial
number of your display monitor in the
space below:
SERIAL No.
The serial number is located on the
rear cover of the monitor.
00PrintVersion_cover 1 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 2
00PrintVersion_cover 2 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 3
English Deutsch Español Français Italiano 01b_XChapterOpener 1 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 4
01b_XChapterOpener 2 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 5
Declaration of the Manufacturer We hereby certify that the colour monitors Diamond Scan 52(M557) Diamond Scan 72(M700) are in compliance with Council Directive 73/23/EEC: - EN 60950 Council Directive 89/336/EEC: - EN 55022 - EN 61000-3-2 - EN 61000-3-3 - EN 55024 and marked with NEC-Mitsubishi Electric Visual Systems Corporation 686-1, NISHIOI OI-MACHI ASHIGARAKAMI-GUN KANAGAWA 258-8533, JAPAN English-1 01_english 1 24/5/01, 3:23 pm English
Inhaltszusammenfassung zur Seite Nr. 6
FCC Information 1. Use the attached specified cables with the Diamond Scan 52/72 colour monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cable or equivalent to ensure FCC compliance. (2) Shielded captive type signal cable. Use of other cables may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
Inhaltszusammenfassung zur Seite Nr. 7
Safety Instruction Caution: When operating the Diamond Scan 52/72 with a 220-240V AC power source in Europe except UK, use the power cord provided with the monitor. In UK, a BS approved power cord with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cord is not supplied with this equipment please contact your supplier. When operating the Diamond Scan 52/72 with a 220-240V AC power source in Australia, use the power cord provided with the monitor. For a
Inhaltszusammenfassung zur Seite Nr. 8
Contents The monitor box* should contains the following: • The monitor with tilt / swivel base Diamond Scan 52 or Diamond Scan 72 • Power cord • Captive Signal Cable • User’s manual * Remember to save your original box and packing material to transport or ship the monitor. English-4 01_english 4 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 9
Tilt / swivel base fixing, removing Fixing This product consists of the monitor and the tilt / swivel base. When fixing the tilt / swivel base to the monitor, please follow the steps below. • Push the hooks of the tilt / swivel base into the holes at the bottom of the monitor. • Then slide the tilt / swivel base forward. • Then the latch above the tilt / swivel base engages it is secure. Removing Please removing the tilt / swivel base when transporting for repair. • Push down the latch of the mo
Inhaltszusammenfassung zur Seite Nr. 10
Quick Start To attach the monitor to your system, follow these instruction: 1. Turn off the power to your computer and the monitor. 2. If necessary, install the display card. For more information, refer to the display card manual. 3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the connector of the display card in your system (Figure A.1) Tighten all screws. For the Mac: Connect the Macintosh Cable Adapter (not included) to the monitor connector on the Macintosh (Figu
Inhaltszusammenfassung zur Seite Nr. 11
Captive Signal Cable Mac Adapter Computer 15-pin mini D-SUB (not included) Figure B.1 Power Outlet Power cord Figure C.1 Figure D.1 English-7 01_english 7 24/5/01, 3:23 pm English
Inhaltszusammenfassung zur Seite Nr. 12
Controls Control Function Power Switch Turn the monitor on and off. Green light - indicates power on. Power LED Indicator Orange light - indicates Off mode. Dark - Switch off. OSD On/ Off Selects OSD functions. Turn on the OSD menu or close the OSD menu. Adjust brightness level or OSD Brightness / OSD Function function select. Select Control Contrast / Adjust Contrast level or OSD OSD Function function adjust. Adjust Control English-8 01_english 8 24/5/01, 3:23 pm
Inhaltszusammenfassung zur Seite Nr. 13
Brightness and Contrast control To adjust the brightness or contrast, press the two keys for brightness or two keys for contrast, to call up the above on-screen display. OSD Function Description 1. Press the key to display the OSD menu. 2. To select a function, press the keys until the desired function is highlighted. 3. Use the keys to increase or decrease the parameter level of the setting. 4. Press the key to close the OSD menu. Colour Temperature The OSD allow you to select a colour te
Inhaltszusammenfassung zur Seite Nr. 14
OSD Icon Summary Icon Function Function Description Brightness Adjusts display brightness Contrast Adjusts display contrast H. Size Increases and decreases screen width H. Position Shifts display image right or left V. Size Increase and decrease screen height V. Position Shifts display image up or down Pin. Balance Adjusts each side of Pincushion Pincushion Adjusts concave and convex portion of pincushion effect Parallelogram Adjusts the tilt of the display sides to the left or right Trapezoid A
Inhaltszusammenfassung zur Seite Nr. 15
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Use the monitor in a clean, dry area. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects o
Inhaltszusammenfassung zur Seite Nr. 16
• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor. If a power cord is not supplied with this monitor, please contact you supplier. Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: • When the power supply cord or plug is damaged. • If liquid has been spilled, or objects have fallen into the monitor. • If the monitor has been exposed to rain or wa
Inhaltszusammenfassung zur Seite Nr. 17
• Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 30 cm and no further away than 70 cm from your eyes. The optimal distance is 45 cm. • Rest your eyes periodically by focusing on an object at least 6 m away. Blink often. • Position the monitor at a 90° Xangle to windows and other light sources to minimize glare and reflections. Adjust th
Inhaltszusammenfassung zur Seite Nr. 18
Specifications Monitor Specifications Diamond Scan 52 Notes Picture Tube Diagonal: 38 cm (15 inch) 90° deflection, 0.28 mm trio dot pitch, Viewable Image Size: 36 cm (14 inch) medium short persistence Radius: 1080 mm phosphor, multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Posi
Inhaltszusammenfassung zur Seite Nr. 19
Monitor Specifications Diamond Scan 72 Notes Picture Tube Diagonal: 43 cm (17 inch) 90° deflection, 0.27 mm trio dot pitch, Viewable Image Size: 41 cm (16 inch) medium short persistence 1210 mm Radius: phosphor, multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Negative)
Inhaltszusammenfassung zur Seite Nr. 20
Features OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along with the flat square technology CRT, a high contrast screen delivers crisp, clean text and graphics. Invar shadow Mask: Holes in the thin metal sheet behind the glass of the CRT surface correspond to each phosphor dot on the inner surface of the CRT’s faceplate, allowing the correct electron beam (red, green, blue) to hit the correct colour phosphor
