Inhaltszusammenfassung zur Seite Nr. 1
PlasmaSync Plasma Monitor
User’s Manual
NEC Technologies
Inhaltszusammenfassung zur Seite Nr. 2
Important Information Precautions Warnings and Safety Precaution Please read this manual carefully before using your NEC The NEC PlasmaSync 42/50PD1 is designed and PlasmaSync 42/50PD1 42/50inch Plasma Monitor and keep manufactured to provide long, trouble-free service. No the manual handy for future reference. maintenance other than cleaning is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel surface. CAUTION The plasma display
Inhaltszusammenfassung zur Seite Nr. 3
To avoid damage and prolong operating life: NOTE: 1. Use only with 120V 50/60Hz AC power supply. Con- When you connect a computer to this monitor, attach tinued operation at line voltages greater than 120 Volts the supplied ferrite cores. If you do not do this, this AC will shorten the life of the unit, and might even monitor will not comform to mandatory FCC standards. cause a fire hazard. Attaching the ferrite cores. 2. Handle the unit carefully when installing it and do not Set the ferrite co
Inhaltszusammenfassung zur Seite Nr. 4
Précautions Mises en garde et précautions de Veuillez lire ce manuel avec attention avant d'utiliser votre sécurité PlasmaSync 42/50PD1 NEC - Moniteur Plasma 42/50 Le moniteur multimédia NEC PlasmaSync 42/50PD1 pouces et conserver ce manuel à portée de la main pour a été conçu et fabriqué pour une utilisation fiable et une consultation ultérieure. durable. Il ne nécessite aucun entretien en dehors du nettoyage. Utiliser un chiffon doux et sec pour nettoyer la surface de l'écran. Ne jamais utilis
Inhaltszusammenfassung zur Seite Nr. 5
Pour éviter le risque de combustion au phosphore, les REMARQUE: mesures suivantes sont recommandées : Lorsque vous branchez un micro-ordinateur sur ce moniteur, fixez les noyaux en ferrites fournis. Si vous Comme tous les appareils d'affichage à base de phosphore ne le faîtes, le moniteur ne sera pas en conformité avec et tous les autres affichages à gaz plasma, les moniteurs les exigences des standards FCC. Plasmasync peuvent être sujets à la combustion au Fixation des noyaux en ferrite. phosph
Inhaltszusammenfassung zur Seite Nr. 6
Limited Warranty Plasma Monitors NEC Technologies, Inc. (hereinafter NECTECH) warrants HOW YOU CAN GET WARRANTY SERVICE this product to be free from defects in material and work- 1. To obtain service on your product, consult the dealer manship under the following terms and, subject to the con- from whom you purchased the product. ditions set forth below, agrees to repair or replace (at 2. Whenever warranty service is required, the original NECTECH's sole option) any part of the enclosed unit da
Inhaltszusammenfassung zur Seite Nr. 7
Contents How to Attacch Options to the Plasma Monitor ............................................................................................. 8 Introduction Introduction to the PlasmaSync 42/50PD1 ...................................................................................... 9 The features you’ll enjoy include ..................................................................................................... 9 Contents of the Package .............................................
Inhaltszusammenfassung zur Seite Nr. 8
How to Attach Options to the Plasma Monitor You can attach your optional mounts or stand to the plasma Drawing A monitor in one of the following two ways: * In the upright position. (See Drawing A) * Lay the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. • This device cannot be installed on its own. Be sure to use a stand or optional mounting unit. (Wall mount
Inhaltszusammenfassung zur Seite Nr. 9
Introduction OSM and IPM are trademarks of NEC Technologies, Inc. (in which case power consumption will be 15 W or less IBM PC/AT, PS/2, VGA, S-VGA, 8514/A and XGA are when not being used). registered trademarks of International Business Machines * The personal computer and the operating system that are Corporation. to be connected must be compatible with VESA DPMS. Apple and Macintosh are registered trademarks of Apple Personal computers that are to be connected to the RGB3 Computer, Inc. input
Inhaltszusammenfassung zur Seite Nr. 10
Setup Procedure 1.Determine the installation location Warning * To ensure safe use, see “Before Use” and “Observe For proper installation and mounting it is strongly recom- the Following,” then install properly. mended to use a trained, authorized NEC dealer. Failure to follow correct mounting procedures could re- 2.Connect the equipment sult in damage to the unit or injury to the installer. Set the termination switch (75Ω/high impedance). Product warranty does not cover damage caused by im- pro
Inhaltszusammenfassung zur Seite Nr. 11
Opening the Terminal Board Attaching the Remote Control Cover Holder Slide the knob and at the same time lift the cover. Insert the top hook of the remote control holder into the installation hole of the main unit and then insert the bot- tom hook into its respective hole. To remove the remote control holder, first release the bot- tom hook, then release the top hook. 1 Knob 2 Removing the Terminal Board Housing the Remote Control in Cover the Remote Control Holder This unit’s terminal board cov
Inhaltszusammenfassung zur Seite Nr. 12
Part Names and Functions Front View 3 1249 56 7 8 1 POWER/STANDBY 5 UP button The lamp color indicates the mode of power on/standby Functions as the (s ) button in the on-screen display or power management. (OSM) mode. 2 Remote control sensor 6 DOWN button Receives the signal from the remote control (when using Functions as the (t ) button in the on-screen display the wireless remote control). (OSM) mode. 3 VIDEO button 7 PROCEED button Switches to the signal connected with the VIDEO input Sets
Inhaltszusammenfassung zur Seite Nr. 13
Side View.... Terminal Board L/R 15
10 16 11 12 17 13 18 14 Insert the prongs completely. * for PLUGGABLE EQUIPMENT, tee socket-outlet shall be installed near the equipment and shall be easily accessible. 15 VIDEO 10 DIP SW IN [BNC] connector (BNC): Inputs the video Sets the various modes of this unit. (composite video signal). IN [S] connector (DIN 4 pin): Inputs the S video (Y/ 11 RGB3 (DVI 29pin) C separate signal). IN connector: Inputs a digital RGB signal. (TMDS) * When connections a
Inhaltszusammenfassung zur Seite Nr. 14
Remote Controller 16 17 1 POWER ON/OFF button: Switches the power on/off. (This does not operate when POWER/STANDBY lamp of the main unit is off.) POWER OFF POWER ON 2 Input selection buttons: 1 Select the input signal that will be displayed on the RGB 2 screen. RGB 1 RGB 3 VIDEO: Switches to the signal that is connected to the 2 VIDEO VIDEO IN connector. RGB1: Switches to the signal that is connected to the POSITION / CONTR OL RGB1 IN (mini D-sub 15-pin) connector. RGB2: Switches to the signal
Inhaltszusammenfassung zur Seite Nr. 15
11 SHARPNESS: Battery Installation and Replacement Adjusts the fine screen quality of the video screen. The remote control is powered by two 1.5V AAA batteries. 12 VISUAL NORMAL button: 1. Press and open the cover. Returns the screen adjustments to the default factory visual settings. 13 RASTER NORMAL button: Returns the screen adjustments to the default factory raster settings. 14 ID SELECT: Selects the ID number used when operating one unit at a time with the remote control when settings of th
Inhaltszusammenfassung zur Seite Nr. 16
Using the wired remote control mode Operating Range * Use the remote controller within a distance of about 7 m Connect the included remote control cable to the remote / 23ft. from the front of the monitor's remote control sen- control's remote jack and "REMOTE IN" jack on the sor and at a horizontal angle of within 30°. monitor. * The remote control operation may not function if the When the cable is connected, the mode automatically monitor's remote control sensor is exposed to direct sun- swit
Inhaltszusammenfassung zur Seite Nr. 17
Making the DIP Switch Settings Before connections are made, the DIP switch should be set to suit the application and the system structure. * DIP switches are moved up or down with something fine and pointed such as a miniature screwdriver or the tip of a ballpoint pen. Note: Be sure to switch off the main power before making settings. DIP Switch Functions and Settings 1 2 3 4 ON Factory Default Settings PIn No. Setting details Setting when shipped Switch position 1 On-off switching of on-screen
Inhaltszusammenfassung zur Seite Nr. 18
Power Management Function The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse have not been used for a fixed period. The power management function of the display becomes operational when the monitor is used with a personal computer based on the VESA DPMS and DVI DMPM system. When preparing to display a personal computer screen, check that the personal computer is properly connected to this unit
Inhaltszusammenfassung zur Seite Nr. 19
HIROYUK AIZASUSUSUSUSSWA HIROYUK AIZ Installation Wiring Diagram PlasmaSync 42/50PD1 Document camera VCR, Video copy
stand or Multimedia application Personal computer
with a digital
RGB (TMDS) output To VIDEO IN inputs
To R,G,B,H/CS, V inputs
(BNC) To RGB3 DVI 29pin
Scan Converter (not supplied) RGBcable (Supplied)
To mini D-SUB 15 Pin input RGBcable (Supplied)
To mini D-SUB 15 Pin input To EXTERNAL CONTROL
(mini D-SUB 15 Pin input) Pin adapter for Macintosh
(not supplied)
Inhaltszusammenfassung zur Seite Nr. 20
Connecting Your PC or Macintosh Connecting Your VCR DVD or Computer Laser Disc Player Connecting your PC or Macintosh computer to your Use a composite video cable with BNC connector and RCA video cables (not provided) to connect your VCR, PlasmaSync 42/50PD1 will enable you to display your DVD or laser disc player to your PlasmaSync 42/50PD1. computer's screen image. All of these following display To make these connections, simply: standards are supported: 1. Turn off the power to your monitor a
