Inhaltszusammenfassung zur Seite Nr. 1
XT5988
15 INCH
COLOR MONITOR
USER'S
MANUAL
Features
• 0.28 mm Dot Pitch
• 1280 x 1024, Non-Interlaced
• 90 Hz Refresh Rate (VGA/SVGA)
• Power Saving Operation (VESA DPMS)
• Non-Glare Screen
• Full Screen Display
• Digital Controls
• RGB Color Match Controls
• Low Radiation
Part #MAN060 Rev. 1.0
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Section 1 General Information ......................................................... 2 Section 2 Installation........................................................................ 3 Section 3 Monitor Controls and LEDs ............................................. 4 Section 4 Troubleshooting ............................................................... 6 Appendix A Specifications ................................................................... 6 Appendix B Video Cable
Inhaltszusammenfassung zur Seite Nr. 3
Section 1 - General Information Congratulations on purchasing a MaxTech 15-inch Color Monitor. The monitor has one of the finest CRTs available in the industry, providing a full range of video display resolutions and complies with the MPR-I standard to reduce electromagnetic emissions. The monitor has a 0.28 mm dot pitch display with a 75 MHz video bandwidth. It supports video resolutions ranging from 640 x 350 to 1280 x 1024 (non-interlaced). The monitor can be used with video cards supporting
Inhaltszusammenfassung zur Seite Nr. 4
Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 5W. While in this mode the first and second LEDs in the Power Indicator (LEDs A and B in Figure 3-1) are off. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top. • Insert the hooks on the swivel base into the slots in the bottom of
Inhaltszusammenfassung zur Seite Nr. 5
• Attach the power cord to the monitor and plug it into an AC outlet. • The monitor is now ready for use. Section 3 - Monitor Controls and LEDs Figure 3-1 Controls and LEDs A B 1 C 13 (on back) 2 12 11 10 9 8 7 6 5 4 3 1. Power Indicator: LEDs A, B, and C (See Figure 3-1) indicate the operational state of the monitor. 1.1 LEDs A, B and C are lit: The monitor is in normal operating mode. 1.2 Only LEDs B and C are lit: The monitor is in the power saving “SUSPEND” mode. In this mode the monitor use
Inhaltszusammenfassung zur Seite Nr. 6
6. Memory Recall Push to reset the display to the default parameters. 7. Dual-Function Toggle Pressing this switch cycles between the two sets of functions controlled by the four pairs of buttons (9-12). When the Function Indicator (8) is off these buttons control Function Group A: Vertical Position, Vertical Size, Horizontal Position and Horizon- tal Size. When the Function Indicator (8) is on, these buttons control Function Group B: Pincushion and RGB Color Adjust- ments. 8. Function Indicator
Inhaltszusammenfassung zur Seite Nr. 7
the blue intensity, The (-) button decreases the blue intensity. 13. Rotation Control (rear of unit) Adjusts display tilt. *Dual function controls. Use the Dual-Function Toggle (7) to switch between Function Group A and Function Group B. Section 4 - Troubleshooting No picture, power indicators A, B, C off • Check AC cord is plugged into outlet and monitor. • Turn on the power switch. No picture, power indicators A, B, C on. • Adjust brightness and contrast controls. No picture, power indicator A
Inhaltszusammenfassung zur Seite Nr. 8
SVGA 800 x 600 72 Hz 48.09 KHz Ultra VGA 1024 x 768 60 Hz 48.37 KHz Ultra VGA 1024 x 768 70 Hz 56.47 KHz Ultra VGA 1280 x 1024 60 Hz 64.31 KHz Synchronization Horizontal: 30-66 KHz Vertical: 50-90 Hz Deflection Geometric distortion H<=2.5mm, V<=2.5mm Linearity distortion H<=10%, V<=8% Pincushion distortion <=2mm High voltage regulation H<=4mm, V<=4mm(0-25FL) Low radiation MPR-I specification Front controls Power, Brightness, Contrast, Horizontal-Size, Horizontal- Position, Vertical-Size, Vertica
Inhaltszusammenfassung zur Seite Nr. 9
Appendix C - Service Port The RJ-45 jack on the rear of the monitor is only used for factory servicing. Do not plug any device into this port. Appendix D - Two Year Warranty MaxTech warrants to the original buyer of this product against defects in material and workmanship for two years from the date of purchase. Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distrib
Inhaltszusammenfassung zur Seite Nr. 10
HOW STATE LAW RELATES TO THE WARRANTY This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Appendix E - Notices FCC Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radi
