Inhaltszusammenfassung zur Seite Nr. 1
LT2323p Wide Flat Panel Monitor
User’s Guide
Inhaltszusammenfassung zur Seite Nr. 2
Product numbers 3024 HC1 First Edition (January 2012) © Copyright Lenovo 2012. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration
Inhaltszusammenfassung zur Seite Nr. 3
Contents Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii General Safety guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Chapter 1. Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Shipping cont
Inhaltszusammenfassung zur Seite Nr. 4
Safety information General Safety guidelines For tips to help you use your computer safely, go to: http://www.lenovo.com/safety Before installing this product, read the Safety Information. íí í iii
Inhaltszusammenfassung zur Seite Nr. 5
Chapter 1. Getting started This User’s Guide contains detailed information on the your Flat Panel Monitor. For a quick overview, please see the Setup Poster that was shipped with your monitor. Shipping contents The product package should include the following items: • Setup Poster • Reference and Driver CD • Flat Panel Monitor •Power Cord •DVI Cable • USB Cable • Analog Interface Cable -attached to monitor Notice for use To set up your monitor, please see the illustrations below. Note: Do not
Inhaltszusammenfassung zur Seite Nr. 6
Product overview This section will provide information on adjusting monitor positions, setting user controls, and using the cable lock slot. Types of adjustments Tilt Please see the illustration below for an example of the tilt range. Swivel With the built-in pedestal, you can tilt and swivel the monitor for the most comfortable viewing angle. Chapter 1. 1-2
Inhaltszusammenfassung zur Seite Nr. 7
Height Adjustment After pressing the top of the monitor, remove the fixed pin and adjust the height of the monitor. Monitor Pivot - Adjust height to the top position before rotation the monitor. - Rotate clockwise until the monitor stops at 90°. Monitor controls Your monitor has controls on the front which are used to adjust the display. For information on how to use these controls, please see "Adjusting your monitor image"on page 2-3. Chapter 1. 1-3
Inhaltszusammenfassung zur Seite Nr. 8
Cable lock slot Your monitor is equipped with a cable lock slot located on the rear of your monitor (in the lower position). Chapter 1. 1-4
Inhaltszusammenfassung zur Seite Nr. 9
Setting up your monitor This section provides information on how to set up your monitor. Connecting and turning on your monitor Note: Be sure to read the Safety information located on page iii before carrying out this procedure. 1. Power off your computer and all attached devices, and unplug the computer power cord. 2. Connect the cables according to below icon indication. 3. Connect one end of the analog signal cable to the monitor VGA connector and the other end to the computer. Chapter
Inhaltszusammenfassung zur Seite Nr. 10
4. Connect the digital cable to the DVI connector of the monitor and the other end on the back of the computer. 5. Connect one end of the DP cable to the DP connector on the back of the computer, and the other end to the DP connector on the monitor. Display Port* * This port does not support being connected to any AV equipment. Lenovo recommends that customers who require to use the Display Port input on their monitor purchase the "Lenovo Display Port to Display Port cable 0A36537".For m
Inhaltszusammenfassung zur Seite Nr. 11
6. Connect the USB cable to the upstream USB port of the back of the monitor and the other end to an appropriate USB port on your computer. Note: The USB port keep available as long as the power supply is right. No matter whether the power button is on or off. 7. Connect the audio cable to audio jack of the monitor and the other end on the external speaker audio in jack. Note: The audio output only for DP mode. Chapter 1. 1-7
Inhaltszusammenfassung zur Seite Nr. 12
8. Insert the power cord into the monitor, then plug the monitor power cord and the computer cord into grounded electrical outlets. Note: A certified power supply cord has to be used with this equipment. The relevant national installation and or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G0.75mm2) shall be used. Alternative a flexibl
Inhaltszusammenfassung zur Seite Nr. 13
11. To install the monitor driver, insert the Reference and Driver CD, click Install driver, and follow the on-screen instructions. 12. To optimize your monitor image, press the Automatic Image Setup key. Automatic image setup requires that the monitor is warmed up for at least 15 minutes. This is not required for normal operation. Note: If automatic image setup does not establish the image that you prefer, perform manual image setup. See "Manual image setup"on page 3-4. Registering
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2. Adjusting and using your monitor This section will give you information on adjusting and using your monitor. Comfort and accessibility Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer. For more detailed i
Inhaltszusammenfassung zur Seite Nr. 15
• Use the monitor brightness, contrast controls, if equipped to optimize the image on your screen to meet your visual preferences. • Keep your monitor screen clean so you can focus on the screen’s contents. Any concentrated and sustained visual activity can be tiring for your eyes. Be sure to periodically look away from your monitor screen and focus on a far object to allow your eye muscles to relax. If you have questions on eye fatigue or visual discomfort, consult a vision care speciali
Inhaltszusammenfassung zur Seite Nr. 16
Adjusting your monitor image This section describes the control features to adjust your monitor image. Using the direct access controls The direct access controls can be used when the On Screen Display (OSD) is not displayed. Table 2-1. Direct access controls Icon Control Description Input Change Switches the video input source Press and hold for 10 seconds to enable or disable DDC-CI the DDC-CI function Exit Exit from menu Image Setup Activates automatic image adjustment Brightness Direct a
Inhaltszusammenfassung zur Seite Nr. 17
Using the On-Screen Display (OSD) controls To adjust the settings, the user controls can be viewed through the OSD. To use the controls: 1. Press to open the main OSD menu. 2. Use or to move among the icons. Select an icon and press to access that function. If there is a sub-menu, you can move between options using or , then press to select that function. Use or to make adjustments. Press to save. 3. Press to move backwards through the sub-menus and exit from the
Inhaltszusammenfassung zur Seite Nr. 18
Table 2-2. OSD functions Controls and Controls and OSD Icon on Main Adjustments Adjustments Menu Submenu Description (Analog) (DVI/DP) Adjusts overall screen Same as Analog brightness Brightness Brightness/ Adjusts difference between Contrast light and dark areas Contrast Moves image left or right. Controls Locked - not required for Horizontal Position DVI/DP input Image Position Moves image up or down. Vertical Position Optimizes image (size, position, phase and clock). Automatic I
Inhaltszusammenfassung zur Seite Nr. 19
Table 2-2. OSD functions Controls and Controls and OSD Icon on Main Adjustments Adjustments Menu Submenu Description (Analog) (DVI/DP) • Selects type of scaled image. Same as Analog • Original AR:Same Aspect Ratio with input Scaling signal. • Full Screen: Expand image to full screen.. Shows resolution, refresh rate, and product details. Same as Analog Note: This screen does not allow any changes to Information Options the settings. Changes languages of menu. Note: The language chosen on
Inhaltszusammenfassung zur Seite Nr. 20
Selecting a supported display mode The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes. The image size, position and shape might change when the display mode changes. This is normal and the image can be readjusted using automatic image setup and the image controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, LCD or Flat Panel technology is inherently fli
