Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTIONS
Thank you for purchasing this JVC Monitor.
Before using the monitor, read this manual carefully so
Model
that you know how to use the Monitor correctly.
Refer to this manual whenever questions or problems
GD-V4210PZW
about operation arise. Be sure to read and observe the
GD-V4210PZW-G
safety precautions.
GD-V4210PCE
Keep this manual where the user can see it easily.
* Installation and removal require special expertise.
GD-V4210PCE-G
Consult your product dealer for details.
GD-V4211P
Inhaltszusammenfassung zur Seite Nr. 2
Safety Precautions FCC NOTICE n GD-V4210PZW / GD-V4210PZW-G / GD-V4210PCE / GD-V4210PCE-G CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equi
Inhaltszusammenfassung zur Seite Nr. 3
– When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator. – Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, r
Inhaltszusammenfassung zur Seite Nr. 4
Parts Identification Remote Control 17 8 DISPLAY ASPECT POWER 9 2 VIDEO A VIDEO B COMPO. RGB 3 MUTING VOLUME p 4 MULTIPLE MONITOR ADJUSTMENT MODE ID SET ID 5 q MENU/EXIT 6 RM-C575 REMOTE CONTROL UNIT 1 Remote signal transmission window 6 MENU/EXIT button Use this button to display or erase menus. 2 DISPLAY button (page 14) While a sub-menu is displayed, pressing this button will Use this button to display the input terminal, color system move you one screen back to the preceding menu. (for VIDEO
Inhaltszusammenfassung zur Seite Nr. 5
Monitor: Front View 12 MENU INPUT POWER MENU INPUT POWER 345 6 Bottom View 1 Remote sensor/power lamp 5 INPUT button (page 14) Point the front end of the wireless remote control toward Use this button to switch between inputs. here. To select the correct RGB input, you have to set “RGB When the Monitor is turned on, the power lamp glows INPUT” correctly on the menu (see page 23). green. It glows orange in standby mode. • Only for GD-V4210PCE, GD-V4210PCE-G and GD-V4211PCE: Only RGB input can be
Inhaltszusammenfassung zur Seite Nr. 6
Parts Identification (Continued) Monitor: Rear Views 4 3 1 2 RL (RS232C) (120/230V) IN SPEAKER OUT (JVC CODE) OUT 5 RL 6 INTERNAL EXTERNAL 7 1 AUDIO output terminal (pin jack) (page 12) 5 SPEAKER OUT terminals (page 12) Connect these terminals to the audio input terminals of Connect external speakers. external equipment such as an amplifier. 6 INTERNAL/EXTERNAL (built-in speaker/external 2 REMOTE 1 (RS232C) terminal (D-sub, 9-pin) (page 12) speaker) selecting switch (page 12) Co
Inhaltszusammenfassung zur Seite Nr. 7
8 9 p 8 RGB B input/output terminals (page 12) 9 RGB A input terminal (D-sub, 15-pin) (page 12) Connect this terminal to the video output terminal of a • R, G, B, HD/Cs, VD input terminals (BNC) personal computer. Connect these terminals to the following output terminals of a personal computer or other equipment: p AUDIO input terminals (pin jack) – Analog RGB signal output terminals Connect these terminals to the audio output terminals of a – Horizontal sync (HD) signal or composite (Cs
Inhaltszusammenfassung zur Seite Nr. 8
Parts Identification (Continued) qw e q VIDEO A terminals (page 13)* Note: • When both the video and S-video terminals are • Video input terminal (BNC) connected, the S-video terminal will have priority. Connect this terminal to the video output terminal of a VCR, etc. e COMPONENT input terminals (page 13)* • Video output terminal (BNC) • Y, PB/B-Y, PR/R-Y input terminals (BNC) Connect this terminal to the video input terminal of Connect these terminals to the component signal ou
Inhaltszusammenfassung zur Seite Nr. 9
Preparations Checking the Accessories The following accessories are included with the Monitor. Check for them. If any item is missing, please contact the dealer where you purchased the Monitor. • Remote control (RM-C575) x 1 • Remote control cable x 1 • Power cord x 3 (Use the one matching the wall outlet.) • Batteries (AA/R6P) x 2 Installing the Batteries Put the batteries in the remote control as follows. If the remote control has become erratic in operation, change the batteries. 1 Remove the
Inhaltszusammenfassung zur Seite Nr. 10
Installation Precautions • When mounting the Monitor vertically, it is necessary to adjust the cooling fan speed to provide better heat dissipation. Do not forget to perform this adjustment. (See page 27.) • When installing the Monitor, be sure to use a dedicated Stand Unit, Wall Mounting Unit, or Monitor Hanger Unit, depending on a particular case. Ask your dealer for installation. • When installing the Monitor, refer also to the user manual for each option to use. Do not tilt the Monitor right
Inhaltszusammenfassung zur Seite Nr. 11
Connections Precautions • Before making connections, turn off all the equipment. • Plugs should be firmly inserted; poor connection could cause noise. • To unplug a cord, be sure to grasp its plug and pull it out. • Connect the power cord after having finished all other connections. • Refer also to the user manual of each piece of equipment. Available Signals Video signals The following signals can be input to this Monitor: • VIDEO A and VIDEO B terminals accept — PAL, NTSC, NTSC4.43, and SECAM
Inhaltszusammenfassung zur Seite Nr. 12
DISPLAY ASPECT POWER VIDEO A VIDEO B COMPO. RGB MUTING VOLUME MULTIPLE MONITOR ADJUSTMENT MODE ID SET ID MENU/EXIT RM-C575 REMOTE CONTROL UNIT Connections (Continued) Connection Examples RGB connections When connecting another Monitor, you can use these RGB B OUT terminals Personal computer 1 To R input To R output (used as the playback source) To audio output To G input To G output To B input To B output When connecting the RGB To HD/Cs input To HD/Cs output terminals, set the RGB INPUT setting
Inhaltszusammenfassung zur Seite Nr. 13
To audio output To video output To audio output To S-video output To video output To audio output To video output AV connections These terminals are not available for GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE. To use them, you need to install video interface kit (IF-C421P1W), which is separately purchased. VCR 1 VCR 2 DVD player, etc (used as the playback source) (used as the playback source) (used as the playback source) Notes: • You can connect another VCR or Monitor to the VIDEO A OUT termi
Inhaltszusammenfassung zur Seite Nr. 14
Basic Operations Daily Operations Rear View 1 Turn on the main power. Set MAIN POWER on the back of the Monitor to ON. The POWER lamp on the upper left of the front panel glows orange. 2 Turn on the power. Press POWER on the remote control to turn the power on. The POWER lamp changes to glow green. • You can also use the POWER on the front panel (lower right) to turn on the Monitor. 3 Select an input. Select the desired input by pressing VIDEO A, VIDEO B, COMPO. or RGB. • You can also se
Inhaltszusammenfassung zur Seite Nr. 15
Changing the Aspect Ratio With this Monitor, you can select among three types of wide screens (FULL, ZOOM, and PANORAMIC) in addition to the REGULAR screen of conventional 4:3 aspect ratio. Press ASPECT to select the screen size Each time you press the button, the screen size changes as ASPECT follows: DISPLAY ASPECT POWER REGULAR FULL VIDEO A VIDEO B COMPO. RGB PANORAMIC ZOOM MUTING VOLUME REGULAR: Displays at conventional 4:3 aspect ratio. MULTIPLE MONITOR ADJUSTMENT ID MODE ID SET MENU/EXIT F
Inhaltszusammenfassung zur Seite Nr. 16
Video Adjustments For video adjustments, use menus. You can use the buttons either on the remote control or on Monitor for menu operations. • Refer also to “Menu Classifications” on pages 33 and 35. Adjusting the Picture Quality Picture quality can be set for each input mode. 1 Press MENU/EXIT (or MENU on the MENU INPUT POWER Monitor) to display the Main Menu. MAIN MENU PICTURE ADJ. Cursor (3) MENU INPUT POWER SIZE/POSITION ADJ. FUNCTION SELECT STATUS DISPLAY ENTER: SELECT: EXIT: MENU 2 Pres
Inhaltszusammenfassung zur Seite Nr. 17
To make an adjustment while viewing the adjustment Adjusting the Screen Size and Position bar After step 3 on page 16, proceed as follows: The screen size and position can be adjusted. Adjusted settings can be stored for each signal type; therefore, 1 Press 5/° to move the cursor (3) to “sub menu.” when the same signal comes in, the stored settings are 2 Press 3 to display the Sub Menu. recalled. The Sub Menu for CONTRAST appears on the screen. • When adjusting the size, the size cannot be adjus
Inhaltszusammenfassung zur Seite Nr. 18
Video Adjustments (Continued) 5 Press 2/3 to adjust the selected item. 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. To make an adjustment while viewing the adjustment bar MENU INPUT POWER After step 3 on page 17, proceed as follows: 1 Press 5/° to move the cursor (3) to “sub menu.” 2 Press 3 to display the Sub Menu. The Sub Menu for H SIZE appears on the screen. MENU INPUT POWER H SIZE :+01 ++ 3 Press 5/° to select the Sub Menu you want to adjust. Each time
Inhaltszusammenfassung zur Seite Nr. 19
Adjusting the Color Temperature Adjusting the White Balance The adjusted setting applies to all inputs. G GAIN, B GAIN and R GAIN can be finely adjusted separately for “HIGH” and “LOW” settings of the color temperature. 1 Press MENU/EXIT (or MENU on the When using plural numbers of the Monitors, this can be Monitor) to display the Main Menu. useful to have the same color on each screen. MAIN MENU PICTURE ADJ. 1 On the remote control: Cursor (3) SIZE/POSITION ADJ. FUNCTION SELECT STATUS DISPL
Inhaltszusammenfassung zur Seite Nr. 20
Video Adjustments (Continued) To make an adjustment while viewing the adjustment bars After step 3 on page 19, proceed as follows: 1 Press 5/° to move the cursor (3) to “sub menu.” 2 Press 3 to display the Sub Menu. The Sub Menu for R GAIN appears on the screen. R GAIN : 000 + – 3 Press 5/° to select the Sub Menu you want to adjust. Each time you press the button, the Sub Menu changes as MENU INPUT POWER follows: R GAIN G GAIN B GAIN MENU INPUT POWER 4 Press 2/3 to adjust the selected item. 5 Re
