Inhaltszusammenfassung zur Seite Nr. 1
PLASMA DISPLAY MONITOR
INSTRUCTIONS
GD-V501PCE
Inhaltszusammenfassung zur Seite Nr. 2
Dear JVC Customer Welcome to the JVC family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Table of Contents Basic Important Safety Notice .............
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Notice WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) WARNING: 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. 2) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Notice FOR UK ONLY IMPORTANT: THE MOULDED PLUG FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. ASA Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains
Inhaltszusammenfassung zur Seite Nr. 5
Safety Precautions WARNING Setup This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by JVC) ................................................... Speakers TS-C5000SPG • ................................................. Stand Unit TS-C50P1G • ....................................... Video Input Card IF-C5
Inhaltszusammenfassung zur Seite Nr. 6
Safety Precautions If problems occur during use If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out from the Plasma Display, immediately unplug the power cord plug from the wall outlet. If you continue to use the Plasma Display in this condition, fire or electric shock could result. After checking that the • smoke has stopped, contact your local JVC dealer so that the necessary repairs can be made. Repairing the Plasma Display yourself is ex
Inhaltszusammenfassung zur Seite Nr. 7
Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book Remote Control Batteries for the Remote Fixing bands × 2 Transmitter Control Transmitter (2 × R6 Size) EUR646526 INPUT SURROUND VOL NR PICTURE SOUND SET UP GD-V501PCE PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY AC cord AC cord Ferrite core Ferrite core (For UK only) (small size) × 1 (large size) × 2 Optional Accessories Speakers Stand Unit Video Input Card • • • TS-C5000SPG TS
Inhaltszusammenfassung zur Seite Nr. 8
Remote Control Batteries Requires two R6 batteries. 1. Turn the transmitter face down. 2. Install the batteries as shown in 3. Replace the cover and slide in Press and slide off the battery the battery compartment. reverse until the lock snaps. cover. (Polarity + or – must match the markings in the compartment.) Two "R6" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause
Inhaltszusammenfassung zur Seite Nr. 9
Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. 1 Speakers (Optional accessories) 2 1 SPEAKERS SPEAKERS AC cord connection 2 Terminals (R) Terminals (L) (see page 14) – Cable fixing bands Secure any excess cables with bands as required. To secure cables connected to Terminals, wrap the Pass the attached cable fixing cable fixing band around them then pass the pointed ban
Inhaltszusammenfassung zur Seite Nr. 10
Connections PC Input Terminals connection COMPUTER AUDIO PC IN POWER / R - STANDBY INPUT – VOL + G POWER ON Less than Conversion adapter Ferrite core (large size) 15 3" /16 (if necessary) (supplied) (10 cm) D-sub 15p RGB PC cable Less than 15 Ferrite core (small size) 3" /16 (supplied) (10 cm) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Installing the ferrite core (Small size) 1 2 3 Open Press the cable Pull back the tabs through and c
Inhaltszusammenfassung zur Seite Nr. 11
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. COMPUTER 6 7 8 9 14 2 3 5 Ferrite core RS-232C (large size) SERIAL Pin layout for RS-232C straight cable (supplied) Installing the ferrite core (Large size) Open Less than D-sub 9p 15 3" /16 (10 cm) Notes: (1) Use the RS-232C cable to connect the computer to the Plasma Display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown ar
Inhaltszusammenfassung zur Seite Nr. 12
Basic Controls INPUT – VOL + R - STANDBY G POWER ON Volume Adjustment Main Power On/Off Switch INPUT button Press the Volume Up “+” Power Indicator (AV(S Video), Component/RGB and or Down “–” button to The Power Indicator will light. PC Mode Selection) increase or decrease the Power-OFF... Indicator not illuminated Press the “INPUT” button to select AV • sound volume level. (The unit will still consume some power as (S Video), Component/RGB and PC long as the power cord is still insert
Inhaltszusammenfassung zur Seite Nr. 13
Basic Controls Explanations from here onward describe the functions when the optional Video Input Card is installed. SURROUND button INPUT button (see page 23) (AV(S Video), Component/RGB and PC Mode Selection) Press to select AV(S Video), Component/RGB and PC input signal modes sequentially. (see page 15) Sound mute On/Off (see page 22) INPUT Volume Adjustment Press the Volume Up “+” or Down “–” button to SURROUND increase or decrease the sound volume level. VOL R button (see page 17) NR ACTION
Inhaltszusammenfassung zur Seite Nr. 14
Power On/Off and input signal selection AC cord connection Connecting the AC cord plug to the Plasma Display. Power On/Off Connecting the plug to the Wall Outlet Note: Main plug types vary between countries. The power plug shown at left may, therefore, not be the type fitted to your set. Press the Power switch on the Plasma Display to turn INPUT — VOL + R - ST G POWER ON ANDBY the set on : Power-On. Power Indicator: Green R - STANDBY G POWER ON Example: The screen below is displayed f
Inhaltszusammenfassung zur Seite Nr. 15
Power On/Off and input signal selection Select the input signal INPUT Press the INPUT button to select the input signal to be played back from the equipment which has been connected to the Plasma Display. Select the input signals to be connected by installing the optional Video Input Card. R - STANDBY INPUT — VOL + G POWER ON (see page 30) Input signals will change as follows: INPUT — VOL + For Component Input AV Component PC For RGB Input AV R
Inhaltszusammenfassung zur Seite Nr. 16
On-Screen Menu Display from Remote Control To Picture adjust menu Press to select each item. (see page 24) Picture Normal Normalise Picture Mode Normal Contrast 20 Brightness 0 Colour 0 Tint 0 INPUT Sharpness 0 White balance Normal SURROUND Setup Advanced settings On Component/RGB-in select RGB VOL To Advanced Settings Signal (see page 24, 25) Screensaver NR ( ) OSD Language English UK Advanced Settings Set up TIMER Normal Normalise Black extension 0 W/B High R 0 W/B High B 0 W/B Low
Inhaltszusammenfassung zur Seite Nr. 17
On-Screen Menu Display from Remote Control Press to access each adjust R screen. Press the R buttun to return to “Setup” menu. To Signal screen for AV To Signal screen for To Signal screen for RGB To Signal screen for PC (see page 30, 31) Component (see page 31) (see page 32) (see page 32) [ ] [ ] [ ] Signal AV Signal [ Component ] Signal RGB Signal PC ( ) 3D Y/C Filter NTSC On 3:2 Pulldown Off Sync H & V Sync H & V Colour system Auto H-Freq. kHz 31.5 H-Freq.
Inhaltszusammenfassung zur Seite Nr. 18
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. ASPECT ASPECT button The aspect mode changes each time the ASPECT button is pressed. 4 : 3 Zoom 16 : 9 INPUT Auto Just SURROUND Notes: VOL (1) During RGB and PC input signal modes, the mode switches between “4:3”, “Zoom” and “16:9” only. NR (2) For a 1,125i (1,080i), 750p (720p) signal input during “Component” input signal
Inhaltszusammenfassung zur Seite Nr. 19
ASPECT Controls Mode Picture Explanation 4:3 will display a 4:3 picture at its standard 4:3 size. 4 4 : 3 4 : 3 3 4 16 Zoom mode magnifies the central section of the Zoom picture. Zoom 3 9 16:9 will display the picture at its maximum size but 4 16 16 : 9 with slight elongation. 16 : 9 3 9 Just mode will display a 4:3 picture at its maximum 4 16 Just size but with aspect correction applied to the center of the screen so that elongation is only apparent at Just 3 9 the left and right edges of the
Inhaltszusammenfassung zur Seite Nr. 20
Adjusting Picture Pos./Size Adjusting screen PICTURE 1 POS. /SIZE Press to display the Picture Pos./Size menu. INPUT SURROUND Press to select H-Pos/H-Size/V-Pos/V- 2 VOL Size/Clock Phase. N R During “AV(S Video)” and During “RGB” and “PC” PICTURE SOUND SET UP “Component” input signal modes. input signal modes. Picture Pos./Size Picture Pos./Size PICTURE POS. /SIZE ASPECT Normal Normal Normalise Normalise H-Pos H-Pos H-Size H-Size V-Pos V-Pos V-Size V-Size PC OFF TIMER Clock Phase Press to adj
