Inhaltszusammenfassung zur Seite Nr. 1
v185e/v185es/v185w/v185ws/w185/w185e/W185q
LCD Monitor User’s Guide
Inhaltszusammenfassung zur Seite Nr. 2
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. This document contains proprietary information that is protected by copyright. N
Inhaltszusammenfassung zur Seite Nr. 3
Preface About This Guide This guide is intended for anyone who uses the v185e / v185es / v185w / v185ws / w185 / w185e / W185q LCD Monitor. It describes the monitor’s features, setup, and operation. The sections are as follows: Safety and Maintenance Guidelines Setup Using the Monitor Installing Drivers and Using the Auto-Adjustment Feature Technical Support FAQs Specifications LCD Monitor Quality and Pixel Policy Agency Regulatory Notices Notational Conventions The
Inhaltszusammenfassung zur Seite Nr. 4
Safety and Maintenance Guidelines Important Safety Information The power cord is designed for use with your monitor. To use a different cord, use only a power source and connection compatible with this monitor. For information on the correct power cord set to use with your monitor, see Power Cord Set Requirements. WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord grounding feature. The grounding plug is an important safety feature.
Inhaltszusammenfassung zur Seite Nr. 5
Install your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord. Do not allow anything to rest on the power cord. Do not walk on the cord. Maintenance Guidelines To enhance the performance and extend the life of your monitor: Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating properly or has been
Inhaltszusammenfassung zur Seite Nr. 6
Setup Base and Tilt Attaching the Base 1 Set the panel face down on a flat , protected surface , such as a table top. 2 Using both hands , align the base with the pedestal and push in firmly to lock in place. Make sure that the base is securely locked in place before continuing with the setup procedure. CAUTION: To prevent damage, avoid applying pressure to the panel front. 6
Inhaltszusammenfassung zur Seite Nr. 7
Removing the Base 1 Set the panel face-down on a flat, protected surface. 2 Squeeze the tabs in the bottom of the base to release the lock. 3 Remove the base from the pedestal. CAUTION: To prevent damage, avoid applying pressure to the panel front. Adjusting the Tilt For optimal viewing, adjust the screen tilt to your own preference, as follows: 1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt. 2 Adjust the tilt by
Inhaltszusammenfassung zur Seite Nr. 8
Cables Attaching the Cables 1 Turn off your computer. 2 If you are attaching a VGA cable, connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of the monitor and connect the other end to the computer VGA port. 3 If attaching a DVI cable, connect one end of the cable to the back of the monitor and connect the other end to the computer. 8
Inhaltszusammenfassung zur Seite Nr. 9
4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet. 5 Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Technical Support FAQs and Using the Monitor. 9
Inhaltszusammenfassung zur Seite Nr. 10
Wall Mounting Arm Preparing to Install a Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm that you purchase separately. CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all power, video, and audio cables. 1 Disconnect the cables from the monitor. 2 With the panel face-down on a protected surface, remove the screws and the pedestal/base attachment. 3 Follow the manufacturer’s instructions to assemble the wa
Inhaltszusammenfassung zur Seite Nr. 11
Using the Monitor Operating Instructions Control buttons are located on the front of the panel, as shown below. Use the Menu button (B) to adjust the display settings to your personal preferences: Set up the monitor, attach the cables, and adjust the tilt as described in the Setup section above. Press the Power button (E) to turn the monitor on and off. The power indicator lights up when the monitor is on. The monitor must be turned on for the other control buttons to work. Set th
Inhaltszusammenfassung zur Seite Nr. 12
External Controls A Auto button Automatically fine-tunes the image quality. B Menu button Opens, selects, or exits the OSD menu. C – (minus) button Navigates backward through the OSD menu and decreases adjustment levels. If the OSD menu is inactive, activates the Volume decrease. D + (plus) button Navigates forward through the OSD menu and increases adjustment levels. If the OSD menu is inactive, activates the Volume increase. E Power button Turns the monitor on or off. F Power L
Inhaltszusammenfassung zur Seite Nr. 13
Settings Setting the Optimal Resolution The recommended resolution for this monitor is 1366 x 768.To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: ® 1 Click the Windows Start Button , and then click Control Panel. 2 Under Appearance and Personalization, click Adjust Screen Resolution. 3 Set the resolution slide bar to 1366 x 768. NOTE: If 1366 x 768 is not
Inhaltszusammenfassung zur Seite Nr. 14
Adjusting On-Screen Display Settings Use the OSD menu to adjust the screen image and change settings. To access the OSD menu: 1 If the monitor is not already on, press the Power button to turn the monitor on. 2 Press the Menu button to activate the OSD menu. 3 Press the – (minus) and + (plus) buttons to navigate through the functions. Once the desired function is highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it displays. Press – (minus) o
Inhaltszusammenfassung zur Seite Nr. 15
OSD Menu The table below shows the OSD menus and their functions at each level. OSD Menu Levels Level 1 Level 2 Level 3 Level 4 Factory Preset Switch Video Input (w185 / W185q only) Brightness Adjustment Scale Y Reset Cancel Save and Return Contrast Adjustment Scale Y Reset Cancel Save and Return Image Control Auto Adjustment “Adjusting” Message Y Horizontal Position Adjustment Scale Y Vertical Position Adjustment Scale Y Fill to Screen Cus
Inhaltszusammenfassung zur Seite Nr. 16
OSD Menu Levels (continued) Level 1 Level 2 Level 3 Level 4 Factory Preset Quick View Movie Photo Gaming Text Y Custom Cancel Save and Return Language Deutsch 简体中文 日本語 English English Español Français Italiano Nederlands Cancel Save and Return Volume(w185 only) OSD Horizontal Adjustment Scale Y Control(w185 only) OSD Position Vertical Adjustment Scale Y OSD Position OSD Transparency Adjustment S
Inhaltszusammenfassung zur Seite Nr. 17
OSD Menu Levels (continued) Level 1 Level 2 Level 3 Level 4 Factory Preset Cancel Save and Return OSD Control Horizontal OSD Adjustment Scale Y (v185w only) Position Vertical OSD Adjustment Scale Y Position OSD Transparency Adjustment Scale Y OSD Timeout Adjustment Scale Y Cancel Save and Return Information Factory Reset Yes No Exit 17
Inhaltszusammenfassung zur Seite Nr. 18
Installing Drivers and Using the Auto-Adjustment Feature Downloading Drivers and Software To download the latest version of drivers and software files from the HP Support Web site: 1 Refer to: http://www.hp.com/support 2 Select your country/region. 3 Select Download Drivers and Software. 4 Enter the model number of your monitor. The software download pages for your monitor will be displayed. 5 Download and install the driver and software files using the instructions in the download pa
Inhaltszusammenfassung zur Seite Nr. 19
Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Problem & Question Possible Solutions Power LED is not on. Make sure the Power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play. In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. Check with your computer manufacturer. Check the monitor’s video cable and make sure none of
Inhaltszusammenfassung zur Seite Nr. 20
Technical Support FAQs (Frequently Asked Questions) (continued) Problem & Question Possible Solutions Missing one of the primary colors (red, Inspect the monitor’s video cable and make sure that none of the pins green, or blue). are bent. Make sure the monitor’s video cable is properly connected to the computer. Screen image is not centered or sized Adjust horizontal and vertical screen position. properly. For VGA input, the auto-adjustment function may fix this problem. Picture h
