Inhaltszusammenfassung zur Seite Nr. 1
17 inch TFT LCD Monitor
USER’S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Inhaltszusammenfassung zur Seite Nr. 3
User’s Manual TCO’99 (FOR OPTIONAL MODEL) Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established m
Inhaltszusammenfassung zur Seite Nr. 4
User’s Manual reduction of electrical and magnetical fields as well as work load and visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Development’s website http://www.tcodevelopment.com or may be ordered from: TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 E-mail: development@tco.se Information regarding TCO’99 approved and labelled products m
Inhaltszusammenfassung zur Seite Nr. 5
User’s Manual and that is needs to be taken care of at end of life according to following information /procedure: http://www.hellmann-pm.de 5
Inhaltszusammenfassung zur Seite Nr. 6
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 7 PRECAUTIONS......................................................................................... 7 SPECIAL NOTES ON LCD MONITORS ................................................... 8 BEFORE YOU OPERATE THE MONITOR.................................................... 9 FEATURES .....................................................................
Inhaltszusammenfassung zur Seite Nr. 7
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interferenc
Inhaltszusammenfassung zur Seite Nr. 8
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of
Inhaltszusammenfassung zur Seite Nr. 9
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 43.2cm(17”) TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Screen Base Cables and User manual Power Cord VGA Cable Audio Cable DVI Cable (dual input mode User’s manual Warra
Inhaltszusammenfassung zur Seite Nr. 10
User’s Manual INSTALLATION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged
Inhaltszusammenfassung zur Seite Nr. 11
User’s Manual CONTROLS AND CONNECTORS CABLE CONNECTIONS: Turn off your computer before performing the procedure below. 1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the 24-pin DVI cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI port. 3. Connect the audio cable between the monitor's audio input and the PC's audio outp
Inhaltszusammenfassung zur Seite Nr. 12
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from 0 ° to 20 °. monitor’s angle Figure.3. NOTES: • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Be car
Inhaltszusammenfassung zur Seite Nr. 13
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor position. The power indicator will light up.
Inhaltszusammenfassung zur Seite Nr. 14
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange — Off mode. • MENU / ENTER: 1. Active OSD menu or function adjust confirm or 2. Exit OSD menu when in volume OSD status. • Volume < >: 1. Activates the volume control when the OSD is OFF. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • Auto Adjust button: When
Inhaltszusammenfassung zur Seite Nr. 15
User’s Manual HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness adjustment: Select the 「Brightness 」option on the 「Main Menu 」. Enter the option and adjust the level. Contrast adjustment: Select the 「Contrast 」option on the 「Main Menu 」. Enter the option and adjust the level. How to adjust screen position and quality: Select 「Image Setting 」on the 「Main Menu 」, and then enter the option. Horizontal position adjustment: Select the 「H-position 」option to shift
Inhaltszusammenfassung zur Seite Nr. 16
User’s Manual OSD Diagram OSD Description Clock adjustment: Select the 「Clock Adjustment 」option to reduce the vertical flicker of characters on the screen. Enter the option and adjust the level. Phase adjustment: Select the 「Phase Adjustment 」option to reduce the horizontal flicker of characters on the screen. Enter the option and adjust the level. How to adjust color: Select the 「Color Setting 」option on the 「Main Menu 」, and then enter the option. Move the cursor t
Inhaltszusammenfassung zur Seite Nr. 17
User’s Manual OSD Diagram OSD Description How to set the OSD: Select 「OSD Setting 」on the 「Main Menu 」, and then enter the option. OSD horizontal adjustment: Select the 「OSD H-Position 」option to adjust the horizontal position of the OSD. Enter the option and adjust the level. OSD vertical position adjustment: Select the 「OSD V-Position 」option to adjust the vertical position of the OSD. Enter the option and adjust the level. OSD timer setting: Select the 「OSD Time-
Inhaltszusammenfassung zur Seite Nr. 18
User’s Manual OSD Diagram OSD Description OSD color setting: Select the 「OSD Color 」setting option to adjust the color of the OSD. Enter the option and adjust the level. Language: Select the 「Language 」 option to change the language of the OSD. Enter the option and select a language. (Reference only, the OSD Language is depended on selected model) Volume adjustment: Select the 「Volume 」option to change the volume level. Enter the option and adjust the level. D
Inhaltszusammenfassung zur Seite Nr. 19
User’s Manual OSD Diagram OSD Description Recall the factory settings: Select the 「Factory Preset 」option to change between the monitor’s default settings and the current settings. Enter the option and select On or Off. Input Setting: Select the 「Input Setting 」 option to change between the analog (D-Sub) or Digital (DVI) source. Enter the option and select Analog or Digital. PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities
Inhaltszusammenfassung zur Seite Nr. 20
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL DEFECTIVE PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position Power LED is not on *Power Cord should be connected *Check if the PC system is Plug & Play compatible No Plug & Play *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices
