Inhaltszusammenfassung zur Seite Nr. 1
HG281
HSG1040
Inhaltszusammenfassung zur Seite Nr. 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Inhaltszusammenfassung zur Seite Nr. 3
User’s Manual Congratulations! The product you have just purchased carries the TCO’06 Media Displays label. This means that your display is designed and manufactured according to some of the strictest performance and environmental criteria in the world. The manufacturer of this display has selected it to be certified to TCO’06 Media Displays as a sign of usability, high performance and reduced impact on the natural environment. Products certified to TCO´06 Media Displays are spec
Inhaltszusammenfassung zur Seite Nr. 4
User’s Manual Recycling Information We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to
Inhaltszusammenfassung zur Seite Nr. 5
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ......................................................................................................6 PRECAUTIONS.....................................................................................................6 SPECIAL NOTES ON LCD MONITORS ..........................................................7 BEFORE OPERATING THE MONITOR ...............................................................8 FEATURES...................................
Inhaltszusammenfassung zur Seite Nr. 6
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference
Inhaltszusammenfassung zur Seite Nr. 7
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
Inhaltszusammenfassung zur Seite Nr. 8
User’s Manual BEFORE OPERATING THE MONITOR FEATURES • 28” Wide screen TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1920 X 1200@60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Power Cord VGA Cable Audio Cable HDMI to DVI-D Cable D-sub to YPbPr Cable 3.5mm Mini
Inhaltszusammenfassung zur Seite Nr. 9
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Turn the monitor over and set it upside down. 2. Align the monitor to the slots on the stand. 3. Please note that the longer edge of the stand should be facing forward. 4. Securely mount the monitor onto the stand using the supplied screws and Allen key. 5. Check the underside of the stand to ensure that the monitor has been firmly installed to the stand a
Inhaltszusammenfassung zur Seite Nr. 10
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the HDMI to DVI-D cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI-D port. 3. Connect the audio cable between the monitor's audio input and the PC's audio output (green
Inhaltszusammenfassung zur Seite Nr. 11
User’s Manual CONNECTING TO A A/V DEVICE: Connect A/V devices via the D-sub and Audio Line in connectors at the back of the monitor. 1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the D-sub to YPbPr adapter cable. 2. Connect the Y (green) connector on the D-sub to YPbPr adapter cable to the Y output connector on the A/V device. 3. Connect the Pb (blue) connector on the D-sub to YPbPr adapter cable to the Pb/Cb output connector on the A/V
Inhaltszusammenfassung zur Seite Nr. 12
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You may adjust the monitor for a viewing angle of 0 to 20 vertically and 0 to 30 horizontally. Monitor Angle Figure.4. NOTES: • Do not touch the LCD screen when you change the angle. It may cause d
Inhaltszusammenfassung zur Seite Nr. 13
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 5). By changing these settings, the picture can be adjusted to your personal preference. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor. The power indicator will light up. Figur
Inhaltszusammenfassung zur Seite Nr. 14
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF monitor’s power. • Power Indicator: Blue — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. • Adjust ▲▼: 1. Adjust Brightness and volume when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • i Button:
Inhaltszusammenfassung zur Seite Nr. 15
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST Adjust the brightness value of the display according to your BRIGHTNESS preference. Select BRIGHTNESS option to adjust the brightness value. Adjust the contrast value of the display according to your CONTRAST preference. Select CONTRAST option to adjust the contrast value. Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the X-CONTRAST contrast is e
Inhaltszusammenfassung zur Seite Nr. 16
User’s Manual Select the H-POSITION option to shift the screen image to the H-POSITION left or right. Enter the option and adjust the level. [For VGA only] Select the V-POSITION option to shift the screen image up or V-POSITION down. Enter the option and adjust the level. [For VGA only] Select the CLOCK option to reduce the vertical flicker of CLOCK characters on the screen. Enter the option and adjust the level. [For VGA only] Select the PHASE option to reduce the horizon
Inhaltszusammenfassung zur Seite Nr. 17
User’s Manual SYSTEM While transferring via the HDMI port, it is recommended to set AUDIO INPUT to HDMI; if no sound is outputted, it is AUDIO INPUT recommended to select AUDIO INPUT as PC, and make sure the PC audio output cable is connected to monitor’s LINE IN (or AUDIO IN) port. [For HDMI Input only] Select the VOLUME option to change the volume level. Enter VOLUME the option and adjust the level. Select the MUTE option to switch the function On or Off. MUTE Select the DDC
Inhaltszusammenfassung zur Seite Nr. 18
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-F
Inhaltszusammenfassung zur Seite Nr. 19
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position Power LED is not on *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible No Plug & Play *Check if any plug pins on the VGA or HDMI connector are bent The display is too dark or too *Adjust the Contrast and Brightness Controls. bright. Picture bounces or
Inhaltszusammenfassung zur Seite Nr. 20
User’s Manual No sound is outputted from *Make sure PC audio output cable is connected to screen s monitor’s built-in speaker LINE IN port (or AUDIO IN port). *Make sure the sound volume adjustment can be clearly identified. *Make sure the System > Silence option in the monitor menu is on. *While transferring via HDMI port but no sound is outputted, it is recommended to select AUDIO INPUT as a PC option, and make sure PC audio output cable is connected to monitor s LINE IN port(o
