Inhaltszusammenfassung zur Seite Nr. 1
HA192
HSG1098
Inhaltszusammenfassung zur Seite Nr. 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Inhaltszusammenfassung zur Seite Nr. 3
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified t
Inhaltszusammenfassung zur Seite Nr. 4
User’s Manual TABLE OF CONTENTS SAFETY NOTICE .................................................................................................. 5 PRECAUTIONS................................................................................................. 5 SPECIAL NOTES ON LCD MONITORS ...................................................... 6 BEFORE YOU OPERATE THE MONITOR ...................................................... 7 FEATURES.................................................
Inhaltszusammenfassung zur Seite Nr. 5
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment.
Inhaltszusammenfassung zur Seite Nr. 6
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0
Inhaltszusammenfassung zur Seite Nr. 7
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 48,3cm / 19” Wide Screen TFT Color LCD Monitor • Crisp, Clear Display for Windows ® • EPA ENERGY STAR • GP Green Product • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Power Cord Warranty Card Quick Start Gui
Inhaltszusammenfassung zur Seite Nr. 8
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged i
Inhaltszusammenfassung zur Seite Nr. 9
User’s Manual SETTING THE MONITOR ON THE WALL DISSEMBLING THE STAND BASE: 1. Disconnect all the cables and cords from the Monitor to prevent breakage. 2. Carefully place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to prevent any damage to the Monitor. 3. Gently remove the stand base. (For reference only) WALL MOUNTING THE MONITOR: 1. Purchase a VESA compatible wall bracke
Inhaltszusammenfassung zur Seite Nr. 10
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer’s VGA port. 2. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other end to Wall outlet. 3. Turn on your monitor and computer. Figure.2. Connecting to a PC 1 VGA Input 2 Power AC Input 10
Inhaltszusammenfassung zur Seite Nr. 11
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5° to 15°. Monitor Angle Figure.3. NOTES: • Do not touch the LCD screen when you change the
Inhaltszusammenfassung zur Seite Nr. 12
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor. The power indicator will light up. Menu / Re
Inhaltszusammenfassung zur Seite Nr. 13
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. • Adjust ▲▼: 1. Adjust Brightness when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or a
Inhaltszusammenfassung zur Seite Nr. 14
User’s Manual Resolution 640x400@70Hz ↔ 720x400@70Hz 640x400@85Hz ↔ 720x400@85Hz 640x480@60Hz ↔ 720x480@60Hz 1024x768@70Hz ↔ 1280x768@70Hz 1280x768@60Hz ↔1360x768@60Hz 1400x1050@60Hz ↔ 1680x1050@60Hz 1400x1050@RB 60Hz ↔ 1680x1050@RB 60Hz 1400x1050@75Hz ↔ 1680x1050@75Hz 1400x900@60Hz ↔ 1600x900@60Hz 1360x768@60Hz ↔ 1366x768@60Hz ** The screen resolutions available will depend on the purchased model. NOTES: • Do not install the monitor in a location near heat sources such
Inhaltszusammenfassung zur Seite Nr. 15
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/ CONTRAST Adjust the brightness value of the display according to your preference. Select「BRIGHTNESS」option to adjust the BRIGHTNESS brightness value. Adjust the contrast value of the display according to your CONTRAST preference. Select「CONTRAST」option to adjust the contrast value. Optimal setting for high contrast images or videos. The dark and light areas of the
Inhaltszusammenfassung zur Seite Nr. 16
User’s Manual initial scale. 「FIT」 indicates scaling by the proportion of original images, which may cause the screen showing black bands. [The availability of this function depends upon the selected model] Select the 「H-POSITION」 option to shift the screen image to the H-POSITION left or right. Enter the option and adjust the level. [For VGA only] Select the 「V-POSITION」 option to shift the screen image up or V-POSITION down. Enter the option and adjust the level. [For VGA only] Se
Inhaltszusammenfassung zur Seite Nr. 17
User’s Manual Select 「OSD TIME-OUT」option to set the OSD time out from OSD TIME-OUT 10 to 100 seconds. Enter the option and adjust the level. To choose the color combination of the OSD window, select OSD COLOR 「OSD COLOR」 option under 「OSD SETTING」 menu, choose modes 1/2/3. SYSTEM While transferring via the HDMI port, it is recommended to set AUDIO INPUT to HDMI; if no sound is outputted, it is AUDIO INPUT recommended
Inhaltszusammenfassung zur Seite Nr. 18
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-F
Inhaltszusammenfassung zur Seite Nr. 19
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position. Power LED is not on *Power Cord should be connected. *Check if the PC system is Plug & Play compatible. *Check if the Video Card is Plug & Play compatible. No Plug & Play *Check if any plug pins on the VGA connector are bent. The display is too dark or too bright. *Ad
Inhaltszusammenfassung zur Seite Nr. 20
User’s Manual output cable is connected to monitor’s LINE IN port(or AUDIO IN port). [For HDMI Input only] Addendum related to Windows 7 When you encounter display problem under Windows 7, you need to do the following: 1. Make sure your PC computer (Hardware requirement) can support Windows 7. 2. Make sure your video card can run Windows 7. 3. If your video card can support Windows 7, need to install the latest Win 7 driver of your video card. Suggest to do the following: 1. I
