Inhaltszusammenfassung zur Seite Nr. 1
English
Monitor
Operating Manual
SCENICVIEW B17-3/B19-3/P19-3
Inhaltszusammenfassung zur Seite Nr. 2
Are there… ... any technical problems or other questions which you would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.com
Inhaltszusammenfassung zur Seite Nr. 3
Inhaltszusammenfassung zur Seite Nr. 4
This manual was produced by Xerox Global Services Published by Fujitsu Siemens Computers GmbH Order No.: A26361-K1143-Z120-1-7619 Edition 3 AG 08/07
Inhaltszusammenfassung zur Seite Nr. 5
SCENICVIEW B17-3/B19-3/P19-3 LCD monitor Operating Manual august 2007 edition
Inhaltszusammenfassung zur Seite Nr. 6
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association. Copyright © Fujitsu Siemens Computers GmbH 2007 All rights, including rights of translation, reproduction by printing, copying or similar methods, in part or in whole, are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification re
Inhaltszusammenfassung zur Seite Nr. 7
Contents Introduction........................................................................................................................................... 1 Notational conventions ................................................................................................................. 2 Important notes..................................................................................................................................... 2 Safety notes............................
Inhaltszusammenfassung zur Seite Nr. 8
Contents A26361-K1143-Z120-1-7619, edition 3
Inhaltszusammenfassung zur Seite Nr. 9
Introduction Your new LCD (Liquid Crystal Display) monitor SCENICVIEW B17-3/B19-3/P19-3 offers numerous features and functions, for example: ● TFT display (Thin Film Transistor; active matrix) ● minimal space requirements thanks to slim casing ● optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners) ● high degree of brightness and good contrast ● high resolution (1280 x 1024) ● presentation of up to 16.7 mil
Inhaltszusammenfassung zur Seite Nr. 10
SCENICVIEW B17-3/B19-3/P19-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. ! Supplementary information, remarks, and tips follow this symbol. i ► Text which follows this symbol describes activities that must be performed in the order shown. "Quotation marks" indicate n
Inhaltszusammenfassung zur Seite Nr. 11
SCENICVIEW B17-3/B19-3/P19-3 ● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never be blocked. ● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure that the local mains voltage lies within these limits. ● Ensure that the power socket on the device or the grounded mains outlet is freely accessible. ● The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the
Inhaltszusammenfassung zur Seite Nr. 12
SCENICVIEW B17-3/B19-3/P19-3 Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath. ● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used. For devices which sit on the
Inhaltszusammenfassung zur Seite Nr. 13
SCENICVIEW B17-3/B19-3/P19-3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference- Causing Equipment Standard ICES-003 for digi
Inhaltszusammenfassung zur Seite Nr. 14
SCENICVIEW B17-3/B19-3/P19-3 Energy Star Guidelines The Fujitsu Siemens LCD monitor SCENICVIEW B17-3/B19-3/P19-3 is designed to conserve electricity by dropping to less than 1 W when it goes into standby, suspend and OFF mode. With this new power management the LCD monitor SCENICVIEW B17-3/B19-3/P19-3 qualifies for the U.S. Environmental Protection Agency's (EPA) Energy Star Computers award. The EPA estimates that computer equipment uses 5 % percent of all business electricity and t
Inhaltszusammenfassung zur Seite Nr. 15
SCENICVIEW B17-3/B19-3/P19-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether the delivery agrees with the details in the delivery note. The complete LCD monitor package includes: – one monitor – one data cable (D-SUB) – one data cable (DVI-D) – one audio
Inhaltszusammenfassung zur Seite Nr. 16
SCENICVIEW B17-3/B19-3/P19-3 Installing an ergonomic video workstation 2 1 1 Avoid glare from electric 1 = Windows 1 = Edge of desk lighting. 2 = Permissible reaching Avoid direct and reflected glare. sector Position the keyboard where it is easiest to reach. 1 0° 65° 30° 60° 30° 65° 2 2 1 = Bearing surface for palms Example layout of monitor, 1 = Preferred viewing distance keyboard and copy-holder of hands 2 = Permissible viewing 2 = Reaching area for distanc
Inhaltszusammenfassung zur Seite Nr. 17
SCENICVIEW B17-3/B19-3/P19-3 Mounting and removing the monitor base The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. ! Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar. The monitor base springs up about 5 cm when the collar is released. ! ► Lay the monitor on its face on a soft surface (A). ► First release one
Inhaltszusammenfassung zur Seite Nr. 18
SCENICVIEW B17-3/B19-3/P19-3 ► Proceed according to the four steps in the illustrations to fold out the monitor base. 10 A26361-K1143-Z120-1-7619, edition 3
Inhaltszusammenfassung zur Seite Nr. 19
SCENICVIEW B17-3/B19-3/P19-3 Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: The display surface is susceptible to scratching! ! ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft surface. ► Remove the cover and disconnect all cables. ► Remove the four screws on the rear of the monitor. You can now mount a swivel arm or a wall bracket as per VESA FPMPMI
Inhaltszusammenfassung zur Seite Nr. 20
SCENICVIEW B17-3/B19-3/P19-3 Connecting the monitor Please take note of the safety information in the "Important notes" chapter. ! CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. Do not cover the ventilation openings of the monitor. The computer power plug must be pulled out! ► Be sure that the monitor and the computer are switched off. 12 A26361-K1143-Z120-1-7619, edition 3
